Epson Projector Eb 825 User Manual

Info  Menu  (Display  Only)
Lets  you  check  the  status  of  the  image  signals  being  projected  and  the  status  of  the  projector.  Items  that  can  be  displayed  vary  depending  on  the  image
signal  and  Source  currently  being  projected  as  shown  in  the  following  screen  shots.  Depending  on  the  model  used,  some  input  sources  are  not
supported.  
s
 p.16
Computer Signal/
Component
 Video
g/US B /US B
Display
Composite
 video
g/S-Video
g
LAN
Sub  MenuFunction
Lamp  HoursYou...

Reset  Menu
Sub MenuFunction
Reset AllYou can reset all items in the Configuration Menu to their default settings.
The following items are not reset to their defaults: Input Signal, User's Logo, all items for Network menus, Lamp Hours, and Language.
Reset Lamp Hours
You can clear the cumulative Lamp Hours use time, and return it to "0H". Reset when you replace the Lamp.
List of Functions
52 

Troubleshooting
This  chapter  explains  how  to  identify  problems  and  what  to  do  if  a  problem  is  found. 

If  a  problem  occurs  with  the  projector,  the  Help  screen  is  displayed  to
assist  you  by  pressing  the  [Help]  button.  You  can  solve  problems  by
answering  the  questions.ProcedureA
Press  the  [Help]  button.
The  Help  screen  is  displayed.
Using the Remote Control Using the Control panel
B
Select  a  menu  item.
Using the Remote Control Using the Control panel
C
Confirm  the  selection.
Using the Remote Control Using the Control panel
Questions  and  solutions  are  displayed  as...

If  you  are  having  a  problem  with  the  projector,  first  check  the  projector's  indicators  and  refer  to  "Reading  the  Indicators"  below.
If the indicators do not show clearly what the problem might be, refer to "When the Indicators Provide No Help". 
s
 p.58
Reading  the  Indicators
The  projector  is  provided  with  the  following  three  indicators  that  indicate  the  operating  status  of  the  projector.
A
Indicates  the  operating  status.
Standby  condition...

If  all  indicators  are  off,  check  that  the  power  cable  is  connected  correctly  and  that  the  power  is  being  supplied  normally.
Sometimes,  when  the  power  cable  is  unplugged,  the  
t indicator  remains  lit  for  a  short  period,  but  this  is  not  a  fault.
t Indicator  is  lit  or  flashing  red
: Lit 
: Flashing: 
: Off
Status Cause Remedy or Status
Internal Error Stop using the projector, disconnect the power cable from the electrical outlet, and contact your local dealer or...

Status Cause Remedy or Status
If it is cracked: Replace it with a new lamp, or contact your local dealer for further advice. If replacing the lamp yourself, be
careful to avoid pieces of broken glass (you cannot continue projecting until the Lamp is replaced). s Epson Projector Contact
List
Check that the lamp cover and lamp are securely installed. s p.69
If the lamp cover or the lamp are not installed correctly, the lamp does not turn on.
When using at an altitude of 1500 m or more, set High Altitude...

When  the  Indicators  Provide  No  Help
If  any  of  the  following  problems  occur  and  the  indicators  do  not  offer
a  solution,  refer  to  the  pages  given  for  each  problem.Problems relating to images
•"No images appear" s  p.59
Projection  does  not  start,  the  projection area  is  completely  black,  the  pro‐
jection  area  is  completely  blue,  and  so  on.
•"Moving images are not displayed" s p.59
Moving  images  being  projected  from  a  computer  appear  black...

Problems  relating  to  imagesNo  images  appear
CheckRemedy
Did you press the [t] button? Press the [t] button to turn the power on.
Are the indicators switched off? The power cable is not connected correctly or power is not being supplied normally.
Connect the projector's power cable correctly. s Quick Start Guide
Check that your electrical outlet or power source is functioning correctly.
Is A/V Mute active?
Press the [A/V Mute] button on the Remote Control to cancel A/V Mute. s p.19
Is the A/V...

The  message  "Not  supported"  is  displayed.
CheckRemedy
Is the image signal format setting correct?
Only when projecting images from a video source
Change the setting according to the signal for the connected equipment. s Signal Menu - Video Signal p.36
Do the image signal Resolution and the Refresh Rate correspond
to the mode?
Only when projecting computer images
Refer to the computer's documentation for how to change the image signal Resolution and the Refresh Rate output
from the...