Epson Projector BrightLink Pro 1430Wi User Manual

Parent topic:
Projector Part Locations
Projector Parts - Touch Unit The Touch Unit comes with the BrightLink Pro 1430Wi projector only.
Front (Cover On)
Front (Cover Off)
1 Dial cover
2 TCH port
3 Security slot
4 Adjustment dials
5 Power light 31   

Rear
1 Laser diffusion ports
2 Installation magnets
3 Guide markers (used for performing angle adjustment)
Parent topic: Projector Part Locations
32  

Projector Parts - Control Pad
1 Power button
2Whiteboard button (switches to whiteboard mode)
3 Source Search button (searches for connected sources)
4 Capture button (captures projected image in annotation mode)
5 Print button (prints the projected image)
6 Save button (saves the projected image)
7 USB-B port for connecting a computer (on bottom of control pad)
8 USB-A port for connecting a USB thumbdrive or other storage device (under bottom cover)
9 Printer USB-A port for connecting a printer (under...

13 Light emitting areas (output remote control signals)
14 Bottom cover (open to connect a USB thumbdrive or other storage device)
15 Top cover (open to connect cables or replace batteries)
16 Cable cover (open when cables are wired along a wall)
Parent topic: Projector Part Locations
34 

Setting Up the Projector
Follow the instructions in these sections to set up your projector for use.
Projector Placement
Removing and Attaching the Cable Cover
Adjusting the Angle of the Touch Unit
Installing the Projector Feet
Projector Connections
Installing Batteries in the Remote Control
Installing Batteries in the Pens
Installing Batteries in the Control Pad
Projector Placement Your ultra-short throw projector is designed to be installed on a wall (with a wall mount) or vertically on a
table (with a...

Mounted on the wall or ceiling
Mounted vertically on a table to create an interactive workspace
Wherever you set up the projector, make sure to position it squarely in front of the screen, not at an
angle.
Parent topic:
Projector Placement
Related references
Projector Setup Settings - Extended Menu
Projection Distance The distance at which you place the projector from the screen determines the approximate size of the
image. The image size increases the farther the projector is from the screen, but can...

mount. You can also use the projector Throw Distance Calculator at
epson.com/support(U.S.) or
epson.ca/support (Canada).
Note: All minimum ceiling heights are based on an image 30 inches (76 cm) from the floor.
16:10 Aspect Ratio Diagonal Min. ceiling Image Image height Min. projection Distance from top
image height widthdistance of image to wall
size plate holes
60 inches 78.7 inches 50.9 31.8 inches 2.5 inches 6.9 inches (17.4 cm) (199.8 cm) inches (80.8 cm) (6.2 cm) (129.2 cm)
70 inches 85.0 inches...

Diagonal Min. ceiling Image width Image height Min. projection Distance from top
image height
distance of image to wall
size plate holes
60 inches 78.1 inches 52.3 inches 29.4 inches 2.9 inches 8.7 inches (22.0 cm) (198.3 cm) (132.8 cm) (74.7 cm) (7.3 cm)
70 inches 84.3 inches 61.0 inches 34.3 inches 5.4 inches 10.0 inches (214.2 cm) (155.0 cm) (87.2 cm) (13.7 cm) (25.4 cm)
77 inches 88.7 inches 67.1 inches 37.8 inches 7.1 inches 11.0 inches (225.3 cm) (170.5 cm) (95.9 cm) (18.1 cm) (27.8 cm)
80 inches...

Parent topic:
Projector Placement
Removing and Attaching the Cable Cover Before you can connect equipment to your projector, you need to remove the cable cover.
1. Remove both of the cable cover screws (screwdriver not included).
2. Slide off the cable cover.
To attach the cable cover, slide it into position and tighten the screws.
Parent topic:Setting Up the Projector
Adjusting the Angle of the Touch Unit You can adjust the angle of the Touch Unit to detect the position of your fingers.
39  

Note:
These instructions require that the Touch Unit is mounted and connected according to the
Installation Guide provided with your projector or projector mount.
1. Turn the projector on.
2. Loosen the screw at the bottom of the Touch Unit.
3. Remove the dial cover from the Touch Unit.
40