Epson Projector BrightLink 585Wi User Manual

4. Close the battery cover and press it down until it clicks into place.
Warning: Dispose of used batteries according to local regulations. Do not expose batteries to heat
or flame. Keep batteries out of the reach of children; they are choking hazards and are very
dangerous if swallowed.
Parent topic: Projector Maintenance
Replacing the Interactive Pen Batteries Each pen uses one AA alkaline or Sanyo Eneloop rechargeable battery. Replace the battery as soon as
it runs out.
When the battery is low, the...

2. Remove the old battery.
Warning: If the battery fluid has leaked, wipe it away with a soft cloth and avoid getting the fluid on
your hands. If it gets on your hands, wash them immediately to avoid injury.
3. Insert the battery with the +and –ends facing as shown.
4. Replace the battery cover and press it down until it clicks into place. Warning: Dispose of used batteries according to local regulations. Do not expose batteries to heat
or flame. Keep batteries out of the reach of children; they are...

1. Twist off the tip of the pen to remove it.
2. Twist on the new tip.
Parent topic:
Projector Maintenance
Transporting the Projector The projector contains precision parts, some of which are glass. Follow these guidelines to transport or
ship the projector safely:
• Remove any equipment connected to the projector.
• When transporting the projector a long distance or as checked luggage, pack it in a firm box withcushioning around it and mark the box Fragile.
• When shipping the projector for repairs,...

Solving Problems
Check the solutions in these sections if you have any problems using the projector.
Projection Problem Tips
Projector Light Status
Using the Projector Help Displays
Solving Image or Sound Problems
Solving Projector or Remote Control Operation Problems
Solving Interactive Problems
Solutions When Network Alert E-Mails are Not Received
Where to Get Help
Projection Problem Tips If the projector is not working properly, try turning it off and unplugging it. Then plug it back in and turn it...

Projector Light Status
The lights on the projector indicate the projector status and let you know when a problem occurs. Check
the status and color of the lights and look for a solution in the table here.
1 Power light
2 Status light
3 Lamp light
4 Temp (temperature) light
Power light Status light Lamp light Temp light Status and solution
Blue BlueOff Off Normal operation.
Blue Flashing blue Off Off Warming up. Wait for an image to
appear.
Blue OffOff Off Standby or sleep mode.
205  

Power light Status light Lamp light Temp light Status and solution
Blue
Flashing blue Off Off Shutting down. (When the Status light
stops flashing, you can unplug the
projector.)
Blue Varies Off Flashing Projector is too hot.
orange• Make sure that the vents and air
filter are not clogged with dust or
obstructed by nearby objects.
• Clean or replace the air filter.
• Make sure the environmental temperature is not too hot.
Off Flashing blue Off Orange Projector has overheated and turned
off. Leave it...

Power light Status light Lamp light Temp light Status and solution
Off
Flashing blue Orange Off Lamp has a problem.
• Check to see if the lamp is burned
out, broken, or installed incorrectly.
Reseat or replace the lamp as
necessary.
• Clean or replace the air filter.
• If operating the projector at high altitude, turn on High Altitude
Mode.
• If the problem persists, unplug the projector and contact Epson for
help.
Flashing blue Varies Flashing Varies Replace the lamp soon to avoid orangedamage. Do not...

Projector Setup Settings - Extended Menu
Where to Get Help
Related tasks
Cleaning the Air Filter and Vents
Replacing the Air Filter
Replacing the Lamp
Using the Projector Help Displays You can display information to help you solve common problems using the projectors Help system.
1. Turn on the projector.
2. Press theHelpbutton on the projector or the remote control.
You see the Help menu.
3. Use the up and down arrow buttons to highlight the problem you want to solve.
4. Press Enterto view the...

Solutions to Microphone Problems
Parent topic:
Solving Problems
Solutions When No Image Appears If no image appears, try the following solutions:
• Press theA/V Mutebutton on the remote control to see if the image was temporarily turned off.
• Make sure all necessary cables are securely connected and the power is on for the projector and connected video sources.
• If you connected your video source to the Monitor Out/Computer2port, make sure you set the
Monitor Out Port setting toComputer2.
• Press the...

Solutions When Image is Incorrect Using the USB Display Function
If no image appears or if the image appears incorrectly using the USB Display function, try the following
solutions:
• Press theUSBbutton on the remote control.
• Make sure the USB Display software has installed correctly. Install it manually if necessary.
• Make sure the USB Type Bsetting in the Extended menu is set to one of the USB Displayoptions.
• With OS X, select the USB Displayicon in the Dock or from the Applicationsfolder.
• For...