Epson Projector BrightLink 585Wi User Manual

1. Hold down the laptops
Fnkey and press the key labelled with a monitor icon or CRT/LCD. (See
your laptop manual for details.) Wait a few seconds for an image to appear.
2. To display on both the laptops monitor and the projector, try pressing the same keys again.
3. If the same image is not displayed by the laptop and projector, check the Windows Displayutility to
make sure the external monitor port is enabled and extended desktop mode is disabled. (See your
computer or Windows manual for...

• Press the
Aspectbutton on the remote control to select a different image aspect ratio.
• If you zoomed into or out of the image using the E-Zoombuttons, press the Escbutton until the
projector returns to a full display.
• Check the cables connecting the computer or video source to the projector. Try connecting different cables.
• Check your computer display settings to disable dual display and set the resolution within the projectors limits. (See your computer manual for details.)
• Check the...

Solutions When the Image Contains Noise or Static
If the projected image seems to contain electronic interference (noise) or static, try the following
solutions:
• Check the cables connecting your computer or video source to the projector. They should be:• Separated from the power cord to prevent interference
• Securely connected at both ends
• Not connected to an extension cable
• No longer than 10 feet (3 m) for VGA/computer cables or 24 feet (7.3 m) for HDMI cables
• Check the settings on the...

Note:
To avoid condensation on the lens after bringing the projector in from a cold environment, let the
projector warm up to room temperature before using it.
• Position the projector close enough to the screen, and directly in front of it.
• Position the projector so the keystone adjustment angle is not so wide that it distorts the image.
• Adjust the Sharpnesssetting to improve image quality.
• If you are projecting from a computer, press the Autobutton on the remote control to automatically
adjust...

Image Quality Settings - Image Menu
Solutions to Sound Problems If there is no sound when you expect it or the volume is too low or high, try the following solutions:
• Adjust the projectors volume settings.
• Press theA/V Mutebutton on the remote control to resume video and audio if they were temporarily
stopped.
• Press the Source Search button to switch to the correct input source, if necessary.
• Check your computer or video source to make sure the volume is turned up and the audio output is set for...

Parent topic:
Solving Image or Sound Problems
Related references
Projector Setup Settings - Extended Menu
Projector Feature Settings - Settings Menu
Related tasks
Connecting a Microphone
Solving Projector or Remote Control Operation Problems Check the solutions in these sections if you have problems operating the projector or remote control.
Solutions to Projector Power or Shut-Off Problems
Solutions to Problems with the Remote Control
Solutions to Password Problems
Parent topic:Solving Problems...

Related tasks
Unlocking the Projectors Buttons
Solutions to Problems with the Remote Control If the projector does not respond to remote control commands, try the following solutions:
• Check that the remote control batteries are installed correctly and have power. If necessary, replacethe batteries.
• Make sure you are operating the remote control within the reception angle and range of the projector.
• Make sure the projector is not warming up or shutting down.
• Check to see if a button on the remote...

Solving Interactive Problems
Check the solutions in these sections if you have problems using the interactive system.
Solutions When Hardware Device Not Found Message Appears
Solutions When Error Occurred in the Easy Interactive Function Message Appears
Solutions When the Interactive Pens Do Not Work
Solutions When Finger Touch Interactivity Does Not Work
Solutions When Manual Calibration Does Not Work
Solutions When the Built-In Toolbar (PC Free Annotation) Does Not Work
Solutions When the Interactive...

Related references
Where to Get Help
Solutions When the Interactive Pens Do Not Work If the interactive pens do not work, try the following solutions:
• The pens turn off automatically if you forget to turn them off. Tap the pen tip or press thepower/function button to turn the pen back on.
• Make sure you are not covering the black section near the tip of the pen.
• Make sure nothing is blocking the signal between the pen and the interactive pen receiver on the projector.
• Try holding the pen at a...

Solutions When Finger Touch Interactivity Does Not Work
If finger touch interactivity does not work (BrightLink 595Wi), try the following solutions:
• Make sure the Touch Unit is installed correctly and the power cable is properly connected. See yourprojectors Installation Guide for details.
• If the light on the Touch Unit is not on, check the Touch Unit Setupsettings in theEasy Interactive
Function option on the Extended menu and make sure the Powersetting is set to On.
• Adjust the angle on the Touch...