Epson Powerlite 6110i Multimedia Projector Users Guide

Configuring the Projector61
■User’s Logo
Turn this setting On to display the image or logo you have 
captured whenever the projector is turned on. See page 
page 66 for more information.
■Projection
Front:
 Projector is in front of the screen.
Front/Ceiling: Projector is in front of the screen, mounted 
upside-down from the ceiling.
Rear: Projector is behind the screen.
Rear/Ceiling: Projector is behind the screen, mounted 
upside-down from the ceiling.
■Operation
Direct Power On:
 When this feature is...

62Configuring the Projector
■Air Filter Setting
Alarm Timer:
 Lets you turn the air filter replacement 
notification on or off. If you are using the smoke air filter, 
make sure this setting is turned 
On.
Timer: Lets you change the amount of time the projector 
waits before displaying the air filter replacement notification.
Clean Notice: When this setting is enabled, the projector 
displays a message when the air filter is clogged with dirt or 
dust. 
Clean Notice Timing: Lets you select from five...

Configuring the Projector63
■Language
Lets you select the language to be used for the projector 
menus.
3. When you’re finished, press 
Esc or Menu.
Selecting Network Settings
For information connecting the projector to a network and 
monitoring the projector over a network, see “Monitoring the 
Projector Over a Network” on page 73. 

64Configuring the Projector
Viewing Lamp Usage and Other 
Information
Use the Info menu to view information about the display settings of 
your computer and video devices and the number of hours the lamp 
and filter have been used.
1. Press the 
Menu button on the remote control and highlight Info.
You see one of the following menus:
■Lamp Hours
Displays the number of hours the lamp has been used. The 
life span of the lamp is about 4000 hours in High or Low 
brightness mode. If the number shown is close...

Configuring the Projector65
■Air Filter
Displays type of air filter and the number of hours it has 
been used.
■Source
Displays the input source currently being used.
■Input Signal (computer, RGB video, and component video)
Displays the input signal currently being used.
■Resolution (computer, RGB video, and component video)
Displays the input resolution currently being used.
■Refresh Rate (computer, RGB video, and component video)
Displays the refresh rate.
■Sync Info (computer, RGB video, and component...

66Configuring the ProjectorIf you assign the projector a password, a screen appears requesting the 
password whenever the projector is turned on. If you enter the 
password incorrectly three times in succession, the projector’s 
operation is locked and you’ll need to disconnect the power cord, then 
reconnect it to redisplay the password screen. If an incorrect password 
is entered 30 times in a row, the projector is locked and you’ll need to 
contact Epson to unlock it. See “Where To Get Help” on page...

Configuring the Projector67
3. Use the  pointer button to highlight User’s Logo, then press 
the 
Enter button.
4. When you see the message 
Choose this image as the User’s 
Logo?
, select Yes and press Enter. A selection box displays over 
the image.
5. Use the  pointer button on the remote control to select the 
area of the image you want to use. Once you have selected the 
area, press 
Enter. 
6. When you see the message 
Select this image?, choose Yes and 
press 
Enter. 
If you want to change the...

68Configuring the Projector7. When you see this screen, select a zoom rate (display size), and 
press 
Enter.
8. When you see the message 
Save this image as the User’s 
Logo?
, select Yes and press Enter. Saving the logo takes a few 
moments. Do not use the projector or other sources (computer, 
video, etc.) while the logo is being saved.
9. When you see the message 
Completed, press Esc.
Displaying Your Screen Logo
Follow the steps below to display your logo when there is no signal, 
when the projector...

Configuring the Projector69
8. To display your screen logo when the A/V Mute button is 
pressed, select 
A/V Mute and press Enter.
9. Select 
Logo and press Enter.
10. When you’re finished, press the 
Menu button on the remote 
control to exit the menu system.
Setting a Password
Follow the steps below to set a password for the projector.
1. Press and hold down the 
Freeze button on the remote control 
until you see the Password Protect menu:
2. Select 
Password and press Enter. 
3. When you see the...

70Configuring the Projector
Protecting Projector Settings
You can password protect the User’s Logo and Network settings to 
prevent them from being changed. Make sure you’ve set a password 
for the projector as described on page 69, then follow the steps below:
1. Press and hold down the 
Freeze button until you see the 
Password Protect menu.
2. To protect your logo from being changed or disabled, select 
User’s Logo Protect and press Enter.
3. Select 
On and press Enter.
4. To protect your network...