Epson Mt532 Manual
Here you can view all the pages of manual Epson Mt532 Manual. The Epson manuals for Printer are available online for free. You can easily download all the documents as PDF.
Page 71
6-8 Assembly and Disassembly Rev. A
Confidential
Pre-assembly D
Reassembly
stepPart name Assembly procedure
4
Cutter, motor assembly
C.B.(M2.3 ´
´ ´ ´
3)´ 1
Screw, switcho
Install the
cutter, motor assembly to the
cutter cover sub-assembly, and
secure it with the
C.B.(M2.3 ´
´ ´ ´
3).
o
Install the
microswitch to the
cutter cover sub-assembly, and secure it with
the
screw, switch.
H
o
Tightening torque: 245 to 294 mN·m {2.5 to 3.0 kg·cm} (
C.B.(M2.3 ´
´ ´ ´
3))
o
Tightening...
Page 72
Rev. A Assembly and Disassembly 6-9 EU-T532/T542 Technical Manual Confidential Pre-assembly D Reassembly stepPart name Assembly procedure H o Make sure not to apply excessive pressure to the microswitch actuator when installing the cutter drive gear sub-assembly. o Make sure not to damage the cutter drive gear sub-assembly when securing it with the R.E. Åo Lubricate the specified areas with G-36. G-36 G-36G-36
Page 73
6-10 Assembly and Disassembly Rev. A Confidential Pre-assembly E Cutter unit Reassembly stepPart name Assembly procedure 1 Cutter cover sub-unit 2 Cutter frame assembly C.B.S-tite (M3 ´ ´ ´ ´ 5)´ 1o Pass the lead wire, paper cutter through the hole on the cutter frame assembly and secure the cutter cover sub-unit and the cutter frame assembly with a screw. o When putting the cutter cover sub-unit and the cutter frame assembly together, insert the shaft, movable cutter blade drive into the...
Page 74
Rev. A Assembly and Disassembly 6-11 EU-T532/T542 Technical Manual
Confidential
Pre-assembly E
Reassembly
stepPart name Assembly procedure
3
Emergency cutter, full, B
C.B.(M2 ´
´ ´ ´
2.5)´ 2o
Install the
emergency cutter, full to the
cutter cover sub-unit with screws.
H
o
Tightening torque: 147 to 196 mN·m {1.5 to 2 kg·cm}
4
Plate, A/Co
Loosen the
C.B.S-tite (M3 ´
´´ ´
5) to attach the
plate A/C to the
cutter cover
sub-unit; tighten it again.
C.B.(M2 ´ 2.5)
plate, A/C
C.B.S-tite (M3 ´ 5)...
Page 75
6-12 Assembly and Disassembly Rev. A Confidential Pre-assembly F Installation of Black mark detector sub-assembly (optional) Reassembly stepPart name Assembly procedure 1 Black mark (B.M.) sub- assembly 2 Paper guide C.P-tite F screw (M2 ´ ´ ´ ´ 3) ´ 1o Install the B.M. detector sub-assembly in one of the two detector mounting holes on the paper guide, and secure it with a screw. Both the straight path and the curved path types can be installed this way. H o Tightening torque: 118 to 216...
Page 76
Rev. A Assembly and Disassembly 6-13 EU-T532/T542 Technical Manual
Confidential
Main Assembly A Installation of the Motor, paper feed, receipt, B and
the Platen detector
Reassembly
stepPart name Assembly procedure
1
Frame assembly
2
Motor, paper feed, receipt,
B
C.B.S-tite (3 ´
´ ´ ´
5)´ 2o
Align the
motor, paper feed, receipt, B with the mounting position on the
frame assembly and secure it with scerws.
H
o
Tightening torque: 686 to 882 mN·m {7 to 9 kg·cm}
o
Make sure that the
motor,...
Page 77
6-14 Assembly and Disassembly Rev. A Confidential Main Assembly A Reassembly stepPart name Assembly procedure H o Tightening torque: 98 to 147 mN·m o After installing the platen detector assembly, arrange the lead wires. lead wires
Page 78
Rev. A Assembly and Disassembly 6-15 EU-T532/T542 Technical Manual
Confidential
Main Assembly B Installation of the Paper guide, straight, front and the
Paper guide, straight, back unit
Reassembly
stepPart name Assembly procedure
1
Paper guide, straight, front
(for the EU-T532)
*For the EU-T542, use the
Paper guide, straight, front,
B.
2
Pin, guide, straight
´ 2o
Insert the
pin, guide, straight into the holes on the
paper guide, straight,
front*.
3
Paper guide, straight, back
unit (for...
Page 79
6-16 Assembly and Disassembly Rev. A
Confidential
Main Assembly B
Reassembly
stepPart name Assembly procedure
H
o
Tightening torque: 588 to 637 mN·m {6 to 6.5 kg·cm}
o
The dowels on the
paper guide, straight, back unit fit securely into the
holes on the
frame assembly.
o
Make sure that the lead wires of the
paper detector assembly are not
caught between the
frame assembly and the
paper guide, straight,
back unit.
o
Make sure that the wires of the
paper detector
assembly are passed...
Page 80
Rev. A Assembly and Disassembly 6-17 EU-T532/T542 Technical Manual Confidential Main Assembly C Installation of the Frame, platen, straight unit Reassembly stepPart name Assembly procedure Ào Lubricate the dowel on the frame assembly with G-36. Áo Lubricate the point where the frame assembly contacts with the lock lever assembly with G-15. 3 Frame, platen, straight unito Install the frame, platen, straight unit to the frame assembly. 4 Shaft, frame, platen R.E. (1.5)´ 1o Align the holes on...