Epson Mt532 Manual

6-28   Assembly and Disassembly Rev. A
Confidential
Module Disassembly (p. 6-38 to 46)
When performing the module disassembly, the modules are disassembled into the following 
parts. When you want to disassemble a corresponding item only, see the page and the step 
numbers in brackets after part names.
Paper roll supply module
oCover, circuit board B (p. 6-30: step 5 to 6)
oPlapoint (p. 6-30: step 5)
oCrescent ring (p. 6-38: step 2 to p. 6-41: step 9)
oPaper roll hold unit (p. 6-38: step 1)
oSpacer,...

Rev. A Assembly and Disassembly   6-29 EU-T532/T542 Technical Manual
Confidential
Note:
oFor the parts marked with (*1) to (*6), new wire bands are required when assembly, since the 
following wire bands used for those parts will be cut during disassembly. See the disassembly steps for 
the position of the wire bands.
(*1): Wire band (SKB-85) 
´ 1
(*2): Wire band (SKB-85) 
´ 1
(*3): Wire band (SKB-85) 
´ 1
(*4): Wire band (SK-1.5M) 
´ 1
(*5): Wire band (SKB-85) 
´ 2
(*6): Wire band (SKB-85) 
´ 2 and wire...

6-30   Assembly and Disassembly Rev. A
Confidential
Unit Disassembly
Cover, circuit board A/B and Control circuit board module
Disassembly 
step Disassembly part name Disassembly procedure
1
Cover, UIB´1
C.B (M3 ´ 
´ ´  ´ 
4)´2o
 Remove the 
C.B (M3 ´
´´ ´
 4) to remove the 
cover, UIB from the 
cover, circuit 
board A.
2
Dust cap´1o
 Remove the 
dust cap from the parallel connector on the circuit board 
module.
3
COM, cover´1o
 Remove the 
COM cover from the serial connector on the circuit board...

Rev. A Assembly and Disassembly   6-31 EU-T532/T542 Technical Manual
Confidential
8
Control circuit board 
module  ´ 1
C.B.(3 ´ 
 ´  ´   ´ 
4)  ´ 4o
 Remove four 
C.B.(3 ´ 
 ´  ´   ´ 
4)s; then remove the control circuit board module.
H

o
 Use a proper body grounding procedure before handling the control 
circuit board module.
o
 Do not deform the parallel connector on the control circuit board 
module by getting caught it on the cover.
9
Cover, circuit board A  ´ 1
C.B.(3 ´ 
 ´  ´   ´ 
4)  ´ 6o
 Remove...

6-32   Assembly and Disassembly Rev. A
Confidential
I

1. Hold two cables for the printer module and a cable for the cut sheet 
presenter module with the 
plate, cable hold; then secure it with two 
C.B. 
(3 ´
´´ ´
 3)s.
    Tightening torque: 539 to 637 mN·m {5.5 to 6.5 kg·cm}
 
   
   ·Hold the cable for the cut sheet presenter module 7.5 cm from the 
connector while aligning it with the frame inside edge of the paper roll 
supply module.
   ·When you pull the cut sheet presenter module fully to the...

Rev. A Assembly and Disassembly   6-33 EU-T532/T542 Technical Manual
Confidential
Paper exit
Disassembly 
step Disassembly part name Disassembly procedure
1
Paper exit´1
C.B.(3 ´ 
´ ´  ´ 
6)´4o
 Remove four 
C.B.(3 ´ 
´ ´  ´ 
6)s; then remove the 
paper exit.
I

o
 Tightening torque for reassembly: 539 to 637 mN·m {5.5 to 6.5 kg·cm}
o
 Do not forget to paste the 
seal, paper exit guide on the 
paper exit.
paper exit
seal, paper exit guide
upper frame, cut sheet presenter unit 

6-34   Assembly and Disassembly Rev. A
Confidential
Cut sheet presenter module, Holding plate, printer, Plate, lower paper guide, 
Plate, paper guide holder, and Holder, paper roll 
Disassembly 
step Disassembly part name Disassembly procedure
1
C.B.(M3 ´ 
´ ´  ´ 
4)´2o
 Remove two 
C.B.(M3 ´ 
´ ´  ´ 
4)s at the bottom of the cut sheet presenter module.
2
Plapoint´1o
 Remove the 
plapoint on the cable side of the cut sheet presenter module.
3o
 Put your fingers on/around the
 seal, paper exit guide and...

Rev. A Assembly and Disassembly   6-35 EU-T532/T542 Technical Manual
Confidential
5
Plate, lower paper 
guide´1
C.B.(M3 ´ 
´ ´  ´ 
4)´2o
 Remove two
 C.B.(M3 ´ 
´ ´  ´ 
4)s; then remove the 
plate, lower paper guide from 
the 
plate, paper guide holder.
I

With the 
plate, lower paper guide tab section inserted in the paper guide of 
the printer module, secure the 
plate, lower paper guide pushed against the 
holding plate, printer with screws.
Tightening torque: 539 to 637 mN·m {5.5 to 6.5 kg·cm}
6...

6-36   Assembly and Disassembly Rev. A
Confidential
7
Plate, paper guide 
holder´1
C.B.(M3 ´ 
´ ´  ´ 
4)´4o Remove two 
C.B.(M3 ´ 
´ ´  ´ 
4)s securing the 
plate, paper guide holder and the 
paper roll supply module, and remove two 
C.B.(M3 ´ 
´ ´  ´ 
4)s securing the 
plate, 
paper guide holder and the 
holding plate, printer; then remove the 
plate, 
paper guide holder.
I

1 Secure the 
plate, paper guide holder to the 
holding plate, printer while 
    pushing it to the 
frame, main of the paper roll...

Rev. A Assembly and Disassembly   6-37 EU-T532/T542 Technical Manual
Confidential
9
C-ring 46´1o
 Remove the 
C-ring 46 from the 
shaft, paper roll.
10
Holder, paper roll ´1o
 Remove the 
holder, paper roll from the 
shaft, paper roll. Disassembly 
step Disassembly part name Disassembly procedure
89
 shaft, paper roll