Epson Mt532 Manual

2-20   Operation Principles Rev. A
Confidential
bps: bits per second
DIP Switch 2
(*1): Fixed to OFF
(*2): Effective only when the serial interface is selected.
Table 2-2 Interface Selection
Interface
Switch No. 2 Switch No.3
Parallel interface (IEEE1284) OFF OFF
Serial interface (RS232) OFF ON
Optional interface ON ON or OFF
Table 2-3 Baud Rate Selection
Transmission speed (bps) Switch No.7 Switch No.8
4800 ON ON
9600 OFF ON
19200 ON OFF
38400 OFF OFF
Table 2-4 DSW 2
SW No. FunctionON OFF
Default...

Rev. A Operation Principles   2-21 EU-T532/T542 Technical Manual
Confidential
Notes: 
~Changes in DIP switch settings (excluding switches 2-7 and 2-8 interface reset signals) are recognized only 
   when the printer power is turned on or when the printer is reset by using the interface.
~If you turn on DIP SWs 2-7 and 2-8 while the printer power is turned on, the printer may be reset, depending on 
   the signal state. DIP switches should not be changed while the printer power is on.
Memory Switches...

2-22   Operation Principles Rev. A
Confidential
(*1): 
·Effective only for the model type with the paper roll supply module
   
·This setting lets the printer tell the paper nearend by sending the secondary paper nearend status when the
     specified length of paper is fed after the primary paper nearend sensor in the paper roll supply module
     detects the paper nearend.
(*2): Effective only when using with the cut sheet presenter module.
Definition of the primary paper nearend and the secondary...

Rev. A Operation Principles   2-23 EU-T532/T542 Technical Manual
Confidential
(*1): Do not set SW 3 to ON in the following condition:
· The partial cutter is used when the cut sheet presenter module is not used.
When backward paper feeding is enabled, the following process is executed.
· After cutting the paper with a 
GS V command, backward paper feeding is executed. (When the Black 
           mark sensor is disabled.)
· The print starting position adjustment with a 
GS (F command can be set to the...

2-24   Operation Principles Rev. A
Confidential 

Rev. AHandling   3-1 EU-T532/T542 Technical Manual
Confidential
Chapter 3
Handling 
Precautions
Transport Precautions
oWhen shipping the printer, use anti-static packing materials.
oRemove a paper roll when transporting the EU-T532/T542.
oMake sure to close the paper roll hold unit
 of the paper roll supply module, the platen unit
 
of the printer module, and the main unit and the upper frame, cut sheet presenter unit
 of 
the cut sheet presenter module when transporting.
Carrying Precautions
oHold the...

3-2   HandlingRev. A
Confidential
Installation Precautions
oWhen installing the unit, secure firmly four mounting parts at the bottom of the paper roll 
supply module to the system side with screws.
oMake sure to ground the unit by using the hole for a ground wire. (See Figure 3-1 for the 
position.)
Note:
If the system side where the unit is installed is not flat, that could cause deformation of parts and 
malfunction. (It is recommended the difference in level is 0.3 mm {0.012} or less.)
Handling...

Rev. AHandling   3-3 EU-T532/T542 Technical Manual
Confidential
oBefore handling the thermal head
, use proper body grounding procedures to avoid 
damage from static electricity.
oMake sure no dust collects on the thermal paper.
oSince the printer uses a line thermal print head, condensation must be avoided. If 
condensation occurs, do not turn on the printer until it has disappeared.
oDo not apply excessive pressure to the thermal head
 connectors. 
oAn FFC can be replaced only ten times; then you must...

3-4   HandlingRev. A
Confidential
Storage Precautions
oDo not store the printer in environments with excessive dust, high temperature, high 
humidity, or in direct sunlight.
oBefore storing the EU-T532/T542 for an extended time, remove the paper and wipe off dirt 
and dust; then clean parts such as the platen
 and the thermal head
 of the printer module, 
rollers of the cut sheet presenter module with alcohol. After the alcohol evaporates, close 
each module and store the unit. 
Note:
If you leave the...

Rev. AHandling   3-5 EU-T532/T542 Technical Manual
Confidential
Cut Sheet Presenter Module
Opening/closing the cut sheet presenter module (See Figure 3-2.)
1. Remove the white screw on the opposite side of the mounting dowels.
2. Put your fingers on/around the seal, paper exit guides 
(green stickers) on the upper 
frame, cut sheet presenter unit
 and on the paper exit
; then pull the cut sheet presenter 
module in the direction of arrow E to slide it in direction E.
Note:
Be careful with your hand, as...