Epson Mt532 Manual

							6-8   Assembly and Disassembly Rev. A
Confidential
Pre-assembly D
Reassembly
stepPart name Assembly procedure
4
Cutter, motor assembly
C.B.(M2.3 ´ 
´ ´  ´ 
3)´ 1
Screw, switcho
 Install the 
cutter, motor assembly to the 
cutter cover sub-assembly, and 
secure it with the 
C.B.(M2.3 ´ 
´ ´  ´ 
3).
o
 Install the 
microswitch to the 
cutter cover sub-assembly, and secure it with 
the 
screw, switch.
H

o
 Tightening torque: 245 to 294 mN·m {2.5 to 3.0 kg·cm} (
C.B.(M2.3 ´ 
´ ´  ´ 
3))
o
 Tightening torque: 108 to 147 mN·cm {1.1 to 1.5 kg·cm} (
screw, switch)
o
 Make sure to install the 
cutter, motor with the labeled side down.
o
 Make sure that the 
cutter, motor is installed securely.
o
 Make sure that the dowel on the 
microswitch fits securely in the mounting 
hole on the 
cutter cover sub-assembly.
5
Cutter drive gear 
sub-assembly
Plain washer (3 ´ 
´ ´  ´ 
0.5 ´ 
´ ´  ´ 
7) ´ 1
R.E. (2.5) 
     ´ 1o
 After lubricating the shaft on the 
cutter cover sub-assembly with G-36, 
install the 
cutter drive gear sub-assembly and the 
plain washer 
on the shaft; then secure them with an
 R.E.
 
screw, switch
C.B.(M2.3 ´ 3)
microswitch
cutter motor
assembly
cutter cover 
sub-assembly
mounting hole
R.E.(2.5)plain washer
cutter drive gear 
sub-assembly
cutter motor
microswitch actuator
G-36 
						

							Rev. A Assembly and Disassembly   6-9 EU-T532/T542 Technical Manual
Confidential
Pre-assembly D
Reassembly
stepPart name Assembly procedure
H

o
 Make sure not to apply excessive pressure to the 
microswitch actuator 
when installing the
 cutter drive gear sub-assembly.
o
 Make sure not to damage the 
cutter drive gear sub-assembly when 
securing it with the 
R.E. 
Åo
 Lubricate the specified areas with G-36.
G-36
G-36G-36 
						

							6-10   Assembly and Disassembly Rev. A
Confidential
Pre-assembly E Cutter unit
Reassembly
stepPart name Assembly procedure
1
Cutter cover sub-unit
2
Cutter frame assembly
C.B.S-tite (M3 ´ 
´ ´  ´ 
5)´ 1o
 Pass the 
lead wire, paper cutter through the hole on the 
cutter frame 
assembly and secure the
 cutter cover sub-unit and the 
cutter frame 
assembly with a screw.
o
When putting the 
cutter cover sub-unit and the 
cutter frame assembly 
together, insert the 
shaft, movable cutter blade drive into the oval hole 
on the 
movable cutter blade.
H

o
 Tightening torque: 686 to 882 mN·m {7 to 9 kg·cm}
o
 Make sure that the 
shaft, movable cutter blade drive fits securely into the 
oval hole on the 
movable cutter blade.
o
 Make sure that the edges of the
 cutter cover sub-unit fit into the hooks on 
the 
cutter frame assembly.
C.B.S-tite (M3 ´ 5)
oval hole
lead wire, paper 
cutter
cutter cover, sub-unit
cutter frame assembly
shaft, movable cutter blade drive
hook
hook
cutter frame assembly
shaft, movable cutter 
blade drive
oval hole
cutter cover, sub-unit
cutter cover, sub-unit 
						

							Rev. A Assembly and Disassembly   6-11 EU-T532/T542 Technical Manual
Confidential
Pre-assembly E
Reassembly
stepPart name Assembly procedure
3
Emergency cutter, full, B
C.B.(M2 ´ 
´ ´  ´ 
2.5)´ 2o
 Install the 
emergency cutter, full to the 
cutter cover sub-unit with screws.
H

o
 Tightening torque: 147 to 196 mN·m {1.5 to 2 kg·cm}
4
Plate, A/Co
 Loosen the
 C.B.S-tite (M3 ´
´´ ´
 5) to attach the 
plate A/C to the 
cutter cover 
sub-unit; tighten it again.
C.B.(M2 ´ 2.5)
plate, A/C
C.B.S-tite (M3 ´ 5)
cutter cover sub unit 
						

							6-12   Assembly and Disassembly Rev. A
Confidential
Pre-assembly F Installation of Black mark detector sub-assembly (optional)
Reassembly
stepPart name Assembly procedure
1
Black mark (B.M.) sub-
assembly
2
Paper guide
C.P-tite F screw (M2 ´ 
´ ´  ´ 
3) 
´ 1o
 Install the 
B.M. detector sub-assembly in one of the two detector 
mounting holes on the 
paper guide, and secure it with a screw. Both the 
straight path and the curved path types can be installed this way.
H

o
 Tightening torque: 118 to 216 mN·m {1.2 to 2.2 kg·cm}
o
 Make sure that the detector
 fits securely into the detector mounting hole 
on the 
paper guide.
C.P-tite. F screw (M2 ´ 3)
B.M. detector sub-assembly
paper guide
mounting hole 
						

							Rev. A Assembly and Disassembly   6-13 EU-T532/T542 Technical Manual
Confidential
Main Assembly A Installation of the Motor, paper feed, receipt, B and 
the Platen detector
Reassembly
stepPart name Assembly procedure
1
Frame assembly
2
Motor, paper feed, receipt, 
B
C.B.S-tite (3 ´ 
 ´  ´   ´ 
5)´ 2o
 Align the 
motor, paper feed, receipt, B with the mounting position on the 
frame assembly and secure it with scerws.
H

o
 Tightening torque: 686 to 882 mN·m {7 to 9 kg·cm}
o
 Make sure that the 
motor, paper feed, receipt, B is oriented properly
.
3
Platen detector assembly
C.P. (1.6 ´ 
 ´  ´   ´ 
5)´ 1o
 Align the 
platen detector assembly to the mounting position on the 
frame 
assembly, and secure it with a screw. 
motor, paper feed, receipt, B
C.B.S-tite (3 ´ 5)
frame assembly
frame assembly
platen detector assembly
C.P. (1.6 ´ 5) 
						

							6-14   Assembly and Disassembly Rev. A
Confidential
Main Assembly A
Reassembly
stepPart name Assembly procedure
H

o
 Tightening torque: 98 to 147 mN·m
o
 After installing the 
platen detector assembly, arrange the lead wires.
lead wires 
						

							Rev. A Assembly and Disassembly   6-15 EU-T532/T542 Technical Manual
Confidential
Main Assembly B Installation of the Paper guide, straight, front and  the
Paper guide, straight, back unit
Reassembly
stepPart name Assembly procedure
1
Paper guide, straight, front 
(for the EU-T532)
*For the EU-T542, use the
 
Paper guide, straight, front,
 B.
2
Pin, guide, straight 
    ´ 2o
 Insert the 
pin, guide, straight into the holes on the 
paper guide, straight, 
front*.
3
Paper guide, straight, back 
unit (for the EU-T532)
C.B. (2.5 ´ 4
 ´ 4 ´ 4  ´ 4
)´ 2
*For theEU-T542, use the
Paper guide, straight, 
back, B unit.o
 After putting the
 paper guide, straight, front and the 
paper guide, straight, 
back unit* together, install them to the mounting holes on the 
frame 
assembly and secure them with screws.
paper guide, straight, front
pin, guide, straight
C.B. (M2.5 ´ 4)
frame, assembly
paper guide, straight,back unit
mounting holes
paper guide, straight, front 
						

							6-16   Assembly and Disassembly Rev. A
Confidential
Main Assembly B
Reassembly
stepPart name Assembly procedure
H

o
 Tightening torque: 588 to 637 mN·m {6 to 6.5 kg·cm}
o
 The dowels on the 
paper guide, straight, back unit fit securely into the 
holes on the 
frame assembly.
o
 Make sure that the lead wires of the 
paper detector assembly are not 
caught between the 
frame assembly and the 
paper guide, straight, 
back unit. 
o
 Make sure that the wires of the 
paper detector 
assembly are passed 
under the hook on the 
paper guide, straight, back unit.
hook
paper guide, straight, 
back unit 
						

							Rev. A Assembly and Disassembly   6-17 EU-T532/T542 Technical Manual
Confidential
Main Assembly C Installation of the Frame, platen, straight unit
Reassembly
stepPart name Assembly procedure
Ào
 Lubricate the dowel on the
 frame assembly with G-36.
Áo
 Lubricate the point where the 
frame assembly contacts with the 
lock 
lever assembly with G-15.
3
Frame, platen, straight unito
 Install the 
frame, platen, straight unit to the 
frame assembly.
4
Shaft, frame, platen
R.E. (1.5)´ 1o
 Align the holes on the 
frame assembly and the 
frame, platen, straight unit, 
and insert the 
shaft, frame, platen into these holes; then, secure it with an 
R.E..
5
6Lever, platen
Spring, lever, plateno
 Install the 
spring, lever, platen on the 
lever, platen, as shown below.
frame, platen, 
straight unit
dowel
frame assembly
G-36point where the frame assembly contacts with 
the lock lever assembly
G-15
G-15
R.E (1.5)
shaft, frame, platen
longer edge
shorter edge
spring, lever, platenlever, platen