Epson M2000 Service Manual

EPSON AcuLaser M2000D/M2000DN/M2010D/M2010DN
Revision B
ADJUSTMENT     
Adjustment
142
5.2  Adjustment5.2.1  Writing USB IDPURPOSEThis printer includes USB interface as standard. A unique USB ID has been assigned to each printer to be identified by a host PC connected via the USB interface. The USB ID information is stored on the nonvolatile memory on the Main Board. Therefore, whenever the Main Board is replaced, the ID must be written to the new board. As for this product, the model ID information is...

EPSON AcuLaser M2000D/M2000DN/M2010D/M2010DN
Revision B
ADJUSTMENT     
Adjustment
143
WRITING METHOD†
USB ID
The method of writing USB ID differs according to the condition of the main board. Referring to the following table, figure out what to do depending on the condition. For the operational procedure, follow the instructions shown by the program.
„
Store optional ID
„
Store auto-generated NEW ID
„
OLD ID Retrieval/Restore
Table 5-1.  Writing Method
Condition of Main Board
Check of the previous ID...

EPSON AcuLaser M2000D/M2000DN/M2010D/M2010DN
Revision B
ADJUSTMENT     
Adjustment
144
†
Model IDSelect [Initial Setting], and select the model name, then click the [Write] button.
CONFIRMING THE WRITTEN IDWhen writing USB ID is finished, print a status sheet to confirm that the serial number printed on the sheet is identical to that on the label attached to the printer. (Refer to “7.3.1 Status Sheet” on page 166
) 

EPSON AcuLaser M2000D/M2000DN/M2010D/M2010DN
Revision B
ADJUSTMENT     
Adjustment
145
5.2.2  Updating firmwareThis section explains how to update the firmwares.
„
Controller firmware
„
Engine controller firmware
OUTLINETOOLFirmware update is executed by transmitting data for updating the program from the computer via USB using the exclusive software tool. Make sure to use the software tool described below.†
Tool Name: Firmware Update Tool
Unit
Data format
Operation
Panel operation
Tool
Controller
RCC...

EPSON AcuLaser M2000D/M2000DN/M2010D/M2010DN
Revision B
ADJUSTMENT     
Adjustment
146
5.2.2.1  Controller Firmware Update
Procedure
RCC data format
CRB data format
1
Check the current version.
Print a status sheet, and check the current firmware version.
Print a status sheet, and check the current firmware version.
2
Connect the printer with 
the computer.
Connect the printer to the computer with a USB cable. Confirm that the Ready light turns on.
After turning the power off for both the printer and...

EPSON AcuLaser M2000D/M2000DN/M2010D/M2010DN
Revision B
ADJUSTMENT     
Adjustment
147
7
Execute the update.
When the transfer is complete, “completed” window pops up. Click [OK].
“Completion” pop-up window will be displayed when the data transfer is finished. Click on the [OK]. 
 
While receiving data, the Ready light blinks and the Paper, Toner, Memory lights turn on.
8
Reboot the Printer.
After confirming that the Ready light turns on, turn the printer power off and turn back on again.
After...

EPSON AcuLaser M2000D/M2000DN/M2010D/M2010DN
Revision B
ADJUSTMENT     
Adjustment
148
5.2.2.2  Engine Controller Firmware Update
Procedure
Method
1
Check the current version.
Print a status sheet or engine status sheet, and check the current firmware version.
2
Connect the printer with the computer.
After turning the power off for both the printer and computer, connect them with a parallel or USB cable.
Make sure to disconnect other unnecessary interface cables from the printer in advance.
3
Prepare the...

EPSON AcuLaser M2000D/M2000DN/M2010D/M2010DN
Revision B
ADJUSTMENT     
Adjustment
149
8
Confirm the checksum.
When updating the program data is finished, the checksum will be indicated on the LCD panel.Confirm the checksum.
9
Reboot the Printer.
Turn the printer off and back on.
10
Print the status sheet.
Prints the status sheet.
11
Check the version on the status sheet.
Check the firmware version printed on the status sheet or engine status sheet and confirm that the firmware is updated.
Procedure
Method 

CHAPTER
6
MAINTENANCE 

EPSON AcuLaser M2000D/M2000DN/M2010D/M2010DN
Revision B
MAINTENANCE     
Cleaning
151
6.1  CleaningClean the parts listed in the table below according to the printer condition.
MAIN UNIT†
Printer exterior surfaceWipe the surface clean with a cloth wrung out of water.
Figure 6-1.  Cleaning the Printer Surface
†
Inside of the printerRemove the Developing unit and the photoconductor unit, and wipe off any paper dust or dirt inside the printer with a dry soft cloth.
Figure 6-2.  Inside of the printer
Table...