Epson M2000 Service Manual

EPSON AcuLaser M2000D/M2000DN/M2010D/M2010DN Revision BDISASSEMBLY AND ASSEMBLY      Main Unit Disassembly/Reassembly 102
Registration Clutch / Paper Feed Clutch / 
Developing Clutch
1. Disconnect the two connectors.2. Remove the two Resin Rings.
A5
Resin Rings
Connectors
Front side
W
B
3. Disconnect the connector, and release the cable from the cable retainers.4. Disengage the hook and remove the bushing.5. Remove the spring and the Grounding Plate.6. Disengage the three hooks and remove the cover.
†...

EPSON AcuLaser M2000D/M2000DN/M2010D/M2010DN Revision BDISASSEMBLY AND ASSEMBLY      Main Unit Disassembly/Reassembly 1037. Remove the Developing Clutch.8. Remove the Gear 1, and remove the Paper Feed Clutch.9. Remove the Gear 2, Gear 3, Gear 4, and Gear 5 in that order, and remove the Registration 
Clutch.Registration Clutch
Paper Feed Clutch
Gear 3
Gear 1
Gear 2
Gear 5
Gear 4
Developing Clutch
Paper Feed Unit
1. Disconnect the three connectors from the Main Board Assy.2. Release the cables from the two...

EPSON AcuLaser M2000D/M2000DN/M2010D/M2010DN Revision BDISASSEMBLY AND ASSEMBLY      Main Unit Disassembly/Reassembly 104
Toner Sensor
1. Remove the screw, and remove the spring.
A) Silver / M3x10 / Washer P-Tite: One piece
2. Disengage the three hooks and remove the Connector Cover.3. Release the cable from the cable retainers on the Connector Cover.4. While pulling out the cable, remove the Toner Sensor.
B6
Toner Sensor
Hooks
Back side
Connector Cover
A
Spring
Front side
MP Paper Sensor
1. Disengage...

EPSON AcuLaser M2000D/M2000DN/M2010D/M2010DN Revision BDISASSEMBLY AND ASSEMBLY      Main Unit Disassembly/Reassembly 105
RFID Board
1. Disengage the three hooks and remove the connector cover.2. Remove the RFID Board from the Paper Feed Unit. (The board is secured to the unit with 
double-faced tape.)
3. Disconnect the connector from the RFID Board.
D6
Hooks
Back side
RFID BoardConnector
Front side 

EPSON AcuLaser M2000D/M2000DN/M2010D/M2010DN Revision BDISASSEMBLY AND ASSEMBLY      Main Unit Disassembly/Reassembly 1064.3.7  Group 7CONTENT
Parts/Units to be Disassembled
Guide
Fuser UnitPaper Eject Unit
AB
Paper Eject Unit
Fuser Unit
A
B 

EPSON AcuLaser M2000D/M2000DN/M2010D/M2010DN Revision BDISASSEMBLY AND ASSEMBLY      Main Unit Disassembly/Reassembly 107DISASSEMBLY FLOWCHART
A5
B7B1
A1
B2
A2
B3
A3
B4B5B6
A4
Start
Left Cover(P. 109)Top Cover(P. 111)
Paper Eject Unit
(P. 111)Fuser Unit(P. 110)Rear Cover(P. 109)
Controller Cover
(P. 108)Right Cover(P. 108) 

EPSON AcuLaser M2000D/M2000DN/M2010D/M2010DN Revision BDISASSEMBLY AND ASSEMBLY      Main Unit Disassembly/Reassembly 108
Controller Cover
1. Remove the screw.
A) Silver / M3x6 / S-Tite: One piece
2. Remove the Controller Cover in the direction of the arrow.
A1
B1
A
Controller Cover
Right Cover
1. Open the Front Cover.2. Slightly pull out the Paper Cassette.3. Remove the screw.
A) Silver / M3x10 / P-Tite: One piece
4. Disengage the five hooks of the Right Cover in the order from the rearmost hook to the...

EPSON AcuLaser M2000D/M2000DN/M2010D/M2010DN Revision BDISASSEMBLY AND ASSEMBLY      Main Unit Disassembly/Reassembly 109
Left Cover
1. Open the Top Cover.2. Slightly pull out the Paper Cassette.3. Remove the three screws.
A) Silver / M3x10 / P-Tite: Three pieces
4. Disengage the six hooks of the Left Cover in the order from the rearmost hook to the 
frontmost one, and remove the Left Cover.
A3
B3
Left Cover
Hooks
AA
A
Rear Cover
1. Open the Rear Cover.2. Pull out the right shaft of the Rear Cover (as...

EPSON AcuLaser M2000D/M2000DN/M2010D/M2010DN Revision BDISASSEMBLY AND ASSEMBLY      Main Unit Disassembly/Reassembly 110
Fuser Unit
1. Disconnect the two connectors from the LVPS Unit.2. Release the cables from the Clamps.
A5
B5
Connectors
Clamps
3. Disconnect the connector from the Main Board Assy.4. Remove the two screws, and remove the Fuser Unit while pulling out the cables through the 
holes.A) Silver / M3x6 / P-Tite: Two pieces
Connector
A
A
Step 3Step 4Fuser Unit 

EPSON AcuLaser M2000D/M2000DN/M2010D/M2010DN Revision BDISASSEMBLY AND ASSEMBLY      Main Unit Disassembly/Reassembly 111
Top Cover
1. Remove the two screws, and remove the Top Cover.
A) Silver / M3x6 / P-Tite: Two pieces
B6
A
A
Paper Eject Unit
1. Remove the five screws and remove the Shield Box together with the Main Board Assy.
A) Silver / M3x6 / S-Tite: Five pieces   	 

Remove the Shield Box from the main unit with the cables connected to the Main Board Assy. Be careful not to disconnect the...