Epson Lq 2180 User Guide

A
Enhancing Your Printer With Options      A-9
10. Adjust the right paper guide so that it matches your paper’s width. 
Make sure the position of the guide allows the paper to move up and 
down freely. Then push the lock lever backward to lock the paper guide.
11. Push back the paper set levers to clamp the paper against the guide 
rollers.
12. Move the cut-sheet feeder’s paper selection lever to the single-sheet 
position, as shown below. Then lift up the center support and close the 
paper guide...

A-10      Enhancing Your Printer With Options
Selecting the paper source (bin 1 or bin 2) 
When the double-bin cut-sheet feeder is installed, you need to select the 
paper source (bin 1 or bin 2) using your application or the printer’s control 
panel. As shown below, the high-capacity cut-sheet feeder is bin 1 and the 
second-bin cut-sheet feeder is bin 2.
It is best to select the paper source in your application program because 
software settings usually override the printer’s control panel settings....

A
Enhancing Your Printer With Options      A-11
Switching between continuous paper and single-sheet 
paper in the cut-sheet feeder
You can easily switch between continuous paper on a push tractor and 
single-sheet paper in the cut-sheet feeder without removing the continuous 
paper.
Switching to continuous paper
1. If any single sheets are in the paper path, press the Load/Eject
 button 
to eject them.
2. Move the printer’s paper release lever to the front or rear push tractor 
position. Also set the...

A-12      Enhancing Your Printer With Options
Using the Roll Paper Holder 
The optional roll paper holder (#8310) allows you to use 8.5-inch roll paper 
like that used with telex machines. This provides an inexpensive alternative 
to using continuous paper for applications that require variable paper 
lengths. Before you install and use the roll paper holder, you need to 
assemble it.
Assembling the roll paper holder
1. Fit the arc bearings into the stand as shown.
2. Make sure you orient the stand and...

A
Enhancing Your Printer With Options      A-13
3. Hook the tension lever onto both ends of the stand as shown below. 
While pulling up the tension lever, fit the wire ends of the tension lever 
into the holes in the stand. The roll paper holder is assembled.
Installing the roll paper holder
1. Make sure the printer is turned off.
2. Position the roll paper holder underneath the printer as shown below. 
Fit the two positioning pegs on the bottom of the printer into the two 
holes in the base plate.
 
c...

A-14      Enhancing Your Printer With Options
Loading roll paper
After you install the roll paper holder, follow the steps below to load a roll 
of paper:
1. Make sure the printer is turned off. Then open the paper guide cover 
and remove the paper guide.
2. Make sure the paper tension unit is installed.
3. Set the paper thickness lever (located under the printer cover) to the 
proper position for the thickness of your roll paper.
4. Set the paper release lever to the single-sheet position.
5. Cut the...

A
Enhancing Your Printer With Options      A-15
7. Place the shaft and paper roll on the roll paper holder so the paper feeds 
from the bottom of the roll. 
8. Turn on the printer. Then bring the leading edge of the paper up over 
the rear push tractor and insert it until it meets resistance. The printer 
loads the roll paper automatically.
9. Replace the paper guide and close the paper guide cover. You are now 
ready to print. The printed roll paper is fed over the paper guide to the 
back of the...

A-16      Enhancing Your Printer With Options
When you finish printing, open the paper guide cover and press the 
LF/FF button to advance the paper. Then tear off the paper using the 
tear-off edge of the printer (pull it towards you for a clean cut).
Removing roll paper
Roll paper cannot be fed backward. To remove roll paper, open the paper 
guide cover and remove the paper guide; then cut the paper behind where 
it feeds into the printer. Press the Load/Eject button to eject the remaining 
paper. 

A
Enhancing Your Printer With Options      A-17
Installing an Interface Card 
Follow the steps below to install an optional interface card.
1. Make sure the printer is turned off. Unplug the printer’s power cord 
and disconnect the interface cable.
2. Remove the screws from the shield plate on the back of the printer and 
remove the plate.
3. Slide the interface card along the slots on both sides of the interface 
compartment. Firmly push in the card to make sure the connector at the 
back of the...

A-18      Enhancing Your Printer With Options
Using the C82305] or C82306] serial interface card
To use the C82305
] or C82306
] serial interface card, see the sections below 
regarding the baud rate, handshake timing, and error handling. 
For all other data transfer conventions, such as word structure and 
communications protocol, see your interface card manual.
Selecting a baud rate
You can select from the following baud rates: 300, 600, 1200, 2400, 4800, 9600, 
and 19200 bps (bits per second). To set...