Epson EPL N3000DT User Manual

358Functions of the Control Panel
Confidential Job Menu
This menu allows you to print or delete print jobs stored in the 
printer’s Hard Disk Drive using the Confidential Job feature of 
the printer driver’s Reserve Job function. You need to enter the 
correct password to access this data. For instructions on using this 
menu, see “Using the Confidential Job Menu” on page 342.
Reset Menu
This menu allows you to cancel printing and reset the printer 
settings.
Clear Warning
Clears the last warning message...

Functions of the Control Panel359
B
B
B
B
B
B
B
B
B
B
B
B
SelecType Init
Restores the control panel menu settings to their default values. 
Yellow Regist, Magenta Regist, and Cyan Regist settings are not 
reset.
Reset Fuser Counter
Reset the fuser unit life when you replace the fuser unit.
Parallel Menu
These settings control communication between the printer and 
the computer when using the parallel interface.
Parallel I/F
Allows you to activate or deactivate the parallel interface.
Speed
Specifies the...

360Functions of the Control Panel
Buffer Size
Determines the amount of memory to be used for receiving data 
and printing data. If Maximum is selected, more memory is 
allocated for receiving data. If Minimum is selected, more memory 
is allocated for printing data.
Note:
❏To activate Buffer Size settings, you must turn off the printer for 
more than five seconds then turn it back on. Or, you can perform a 
Reset All operation, as explained in “Reset Menu” on page 358. 
❏Resetting the printer erases all...

Functions of the Control Panel361
B
B
B
B
B
B
B
B
B
B
B
B
Note:
❏To activate Buffer Size settings, you must turn off the printer for 
more than five seconds then turn it back on. Or, you can perform a 
Reset All operation, as explained in “Reset Menu” on page 358. 
❏Resetting the printer erases all print jobs. Make sure the Ready light 
is not flashing when you reset the printer.
Network Menu
See the Network Guide for each setting.
AUX Menu
See the Network Guide for each setting.
 

362Functions of the Control Panel
LJ4 Menu
These settings control the fonts and symbol sets when in the LJ4 
mode.
Item Settings (default in bold)
Font SourceResident, Download*
Font Number0 to 65535 (depending on your settings)
Pitch** 0.44 ... 10.00 ... 99.99 cpi in 0.01-cpi increments
Height** 4.00 ... 12.00 ... 999.75 pt in 0.25-pt increments
SymSetIBM-US, Roman-8, Roman-9, ECM94-1, 8859-2 
ISO,8859-9 ISO, 8859-10ISO, 8859-15ISO, 
PcBlt775, IBM-DN, PcMultiling, PcE.Europe, 
PcTk437, PcEur858, Pc1004,...

Functions of the Control Panel363
B
B
B
B
B
B
B
B
B
B
B
B
* Available only when the download fonts are installed.
Note:
If you normally use the HP LaserJet 4 printer driver when printing, you 
should change settings using this driver whenever you can. Printer 
driver settings always override the LJ4 Menu options.
FontSource
Sets the default font source.
Font Number
Sets the default font number for the default font source. The 
available number depends on the settings you made.
Pitch
Specifies the default...

364Functions of the Control Panel
Form
Selects the number of lines for the selected paper size and 
orientation. This also causes a line spacing (VMI) change, and the 
new VMI value is stored in the printer. This means that later 
changes in the Page Size or Orientation settings cause changes in 
the Form value, based on the stored VMI.
Source SymSet, Dest SymSet
Available only in certain locations where printers are sold with a 
special ROM module installed to handle specific languages.
CR Function, LF...

Functions of the Control Panel365
B
B
B
B
B
B
B
B
B
B
B
B
GL2 Menu
This menu lets you set the printer to emulate a plotter, allowing 
you to use software which requires a plotter for output. The 
LJ4GL2 mode is similar to the GL/2 mode supported in the HP 
LaserJet 4 mode. The GLlike mode emulates some of the HP-GL 
plotter commands and includes all the commands found in HP’s 
GL/2 mode, as well as two additional commands.
* Available only when GLlike is selected as the GL Mode.
Before you start printing...

366Functions of the Control Panel If you need to configure the printer settings, first switch to the 
GL/2 emulation mode, then change the settings using the printer 
driver, or the control panel menus.
Note:
Settings or data saved in the printer’s RAM (such as downloaded fonts) 
may be erased when you change the emulation mode.
GL Mode
Specifies whether the printer uses a direct emulation of the GL/2 
plotter language, or the HP LaserJet 4 emulation of GL/2.
Scale
Specifies whether the output from the...

Functions of the Control Panel367
B
B
B
B
B
B
B
B
B
B
B
B
Join
Specifies the way in which lines are joined.
Pens 0 through 6
Allows you to set the thickness of the pens used to make the 
printout. Pen 0 and Pen 1 are available in the LJ4GL2 mode, and 
Pen 0 through Pen 6 are available in the GLlike mode.
PS3 Menu
These settings are available in the PS3 mode.
Error Sheet
When you select On, the printer prints out an error sheet.
Image Protect
Allows you to specify whether to employ lossy compression....