Epson EPL N3000D User Manual
Have a look at the manual Epson EPL N3000D User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1734 Epson manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
198Installing Options 6. To confirm that the option is installed correctly, print a Status Sheet. See “Printing a Status Sheet” on page 260. See “Printing with the Duplex Unit” on page 54 for information about duplex printing. Note: If you are using Windows, and EPSON Status Monitor 3 is not installed, you have to make settings manually in the printer driver. Click the Update the Printer Option Information Manually button on the Optional Settings menu, then click Settings. Then select the Duplex Print Unit check box in the Optional Settings dialog box and click OK. Removing the Duplex Unit Follow these steps to remove the optional Duplex Unit. 1. Turn the printer off and unplug the power cord and interface cable. 2. Loosen the two screws on the lower sides of the Duplex Unit.
Installing Options199 7 7 7 7 7 7 7 7 7 7 7 7 3. Press the unlock button to unlock the hooks, then remove the unit from the printer. 4. Attach the option cover to cover B. 5. Reconnect the interface cable and power cord, then turn the printer on. Stacker Follow these steps to install the optional Stacker. 1. Turn off the printer and unplug the power cord and interface cable.
200Installing Options 2. Lift the second lever at the top left corner of the back of the printer. 3. Open cover B. 4. Remove the locking clip, and then lift the right and left levers to remove the top cover.
Installing Options201 7 7 7 7 7 7 7 7 7 7 7 7 5. Insert the right and left tabs of the Stacker into the holes on the top of the printer and slowly lower it onto the top of the printer. 6. Secure the screws at both ends of the bottom of the stacker. 7. Close cover B.
202Installing Options 8. Attach the locking clip that was shipped with the Stacker and pull out the extension tray. 9. Reconnect the interface cable and power cord, and then turn on the printer. Removing the Stacker Follow these steps to remove the optional Stacker. 1. Turn off the printer and unplug the power cord and interface cable. 2. Close the extension tray of the Stacker and remove the locking clip.
Installing Options203 7 7 7 7 7 7 7 7 7 7 7 7 3. Lift up the second lever at the top left corner of the back of the printer to open cover B. 4. Remover the screws on both sides of the Stacker, and while holding up the Stacker, remove the right and left tabs from the holes on the top of the printer.
204Installing Options 5. Insert the right and left tabs of the top cover into the holes on the top of the printer, and then attach the locking clip that was shipped with the printer. 6. Reconnect the interface cable and power cord, and then turn on the printer. Memory Module By installing a Dual In-line Memory Module (DIMM), you can increase printer memory up to 512 MB. You may want to add additional memory if you are having difficulty printing complex graphics. Note: Memory modules from 16 MB to 256 MB are supported. Follow these steps to install an optional memory module. w Warning: Be careful when working inside the printer as some components are sharp and may cause injury.
Installing Options205 7 7 7 7 7 7 7 7 7 7 7 7 c Caution: Before you install a memory module, be sure to discharge any static electricity by touching a grounded piece of metal. Otherwise, you may damage static-sensitive components. 1. Turn the printer off and unplug the power cord and interface cable. 2. Remove the cover on the printer’s right side by removing the screw on the back of the printer and sliding the cover backward.
206Installing Options 3. Loosen the two screws using a screwdriver. Then hold the tab on the top of the shield cover and remove the cover. w Warning: Removing other screws and covers will expose high voltage areas. 4. Identify the RAM slot. RAM slot (gray)
Installing Options207 7 7 7 7 7 7 7 7 7 7 7 7 5. Insert the memory module into slot until the clip lock onto the memory module. Make sure that the left slot (white) has a module at all times. c Caution: ❏Do not force the memory module into the slot. ❏Be sure to insert the memory module facing the correct way. ❏You should not remove any modules from the circuit board. Otherwise, the printer will not work.