Epson Brightlink 450wi Interactive Projector Users Guide

Using the Projector Menus81
The password screen closes and projection begins.
If projection does not begin, check the following:
■If the password is not correct, you see a message prompting you to 
re-enter the password. If you enter an incorrect password three 
times in succession, you see an error code with the message 
The 
projector’s operation will be locked 
and the projector switches 
to standby mode. Write down the error code, then disconnect the 
projector’s power cord from the electrical...

82Using the Projector Menus
Capturing the Image
Start by displaying the image you want to use from either a computer 
or video source, such as a DVD player or digital camera. Then follow 
these steps to capture the image and transfer it to the projector: 
1. Press the 
Menu button on the remote control, highlight the 
Extended menu, and press Enter.
2. Highlight 
User’s Logo and press Enter. 
3. When you see a message asking 
Choose this image as the 
User’s Logo?
, select Yes and press Enter. A...

Using the Projector Menus83
Choosing When to Display the Image
After your image is saved, you can set it to display as the startup 
screen, the screen you see when there’s no signal, or the screen you see 
when you press the 
A/V Mute button (see page 60).
1. Press the 
Menu button, highlight the Extended menu, and press 
Enter. 
2. Select 
Display and press Enter.
3. Choose from these display options:
■Set Display Background to Logo to display your image 
when there is no signal. 
■Set Startup Screen to...

84Using the Projector Menus5. Press the 
Menu button to exit. 
To disable the Control Panel Lock function, select 
Off in the Control 
Panel Lock menu. Or press and hold the 
Enter button on the 
projector’s control panel for seven seconds. A message is displayed and 
the lock is released.
Using Security Locking
The projector includes two security locking points to prevent its theft 
when installed or used in public locations: 
■Security cable attachment. You can attach a commercially 
available security...

85
6l
Using the Projector on a 
Network
This chapter tells you how to prepare to send images to your 
projector through a wired or wireless network. 
Using EasyMP Network Projection, you can project images shown on 
your computer screen—including text, graphics, and video—directly 
to your audience. See the EasyMP Network Projection Operation Guide 
for information on features and use. 
You can use EasyMP Monitor (available for Windows only) to 
monitor and control your projector through the network. For...

86Using the Projector on a NetworkProjection Operation Guide for instructions on installing the software. 
The guide also contains instructions on using the software to project 
over the network.
If you want to use the interactive pens while projecting through a 
wired or wireless network, you must set the 
USB Type B option to 
Wireless Mouse in the Extended menu. See page 78 for more 
information.
Connecting to a Wired Network
With a shielded, Category-5 Ethernet cable, you can connect the 
projector...

Using the Projector on a Network87
4. Press the LAN button on the remote control to select network as 
the source. 
5. Press the 
Menu button on the remote control, select the 
Network menu, then press Enter. 
6. Choose 
Network Configuration and press Enter.
7. Select the 
Wired LAN menu and press Enter. 
8. Choose 
IP Settings and press Enter. You see a screen like the 
following:
9. Do one of the following:
■If your network assigns addresses automatically, turn on the 
DHCP setting. 

88Using the Projector on a Network
■If your network does not assign addresses automatically, turn 
off 
DHCP and enter the projector’s IP Address, Subnet 
Mask
, and Gateway Address, as needed. 
To enter numbers, use the arrow buttons on the remote 
control to select each number on the screen, then press the 
Enter button. When you’re finished entering an address in 
the network menu, highlight 
Finish, then press the Enter 
button.
10. Press 
Esc to return to the previous menu.
11. To prevent the IP...

Using the Projector on a Network89
Installing the Optional Wireless LAN 
Module
Make sure you have the optional Wireless LAN Module. Turn off the 
projector and disconnect the power cord before you install the 
module.
1. Open the air filter cover by sliding the switch and lifting the 
cover. 

90Using the Projector on a Network2. Insert the wireless LAN module as shown.
3. As a security feature, you can fasten the module using the screw 
that came with it.
4. Close the air filter cover.
If you have the optional Quick Wireless Connection USB key 
(V12H005M005), you can use Quick Wireless connection as 
described in the next section (Windows only). Or, you can configure 
your connection manually as described on page 91.
Insert 
screw here