Epson Aculaser M2010D User Manual

							Cleaning and Transporting the Printer71
4. Wipe paper dust and marks from the metal roller inside the printer with a dry and soft cloth as 
shown below. 
* metal roller 
5. Move the green cleaning lever of the photoconductor wire back and forth slowly several times 
from one end to the other.
Note:
❏If the protective tape is stuck on the photoconductor unit, remove the tape before moving the cleaning 
lever.
❏After cleaning, make sure to return the green cleaning lever to the original position until it locks.
 
						

							Cleaning and Transporting the Printer72
6. Insert the photoconductor unit slowly all the way in.
7. Insert the developer unit containing the toner cartridge slowly all the way in.
8. Close the top cover and MP tray.
 
						

							Cleaning and Transporting the Printer73
Transporting the Printer
Finding a place for the printer
When relocating the printer, always choose a location that has adequate space for easy operation 
and maintenance. Use the following illustration as a guide for the amount of space required around 
the printer to ensure smooth operation.
a. 20 cm
b. 20 cm
c. 30 cm
d. 50 cm
e. 30 cm
To install and use any of the following options, you will need the indicated amount of additional 
space.
The 250-sheet paper cassette unit adds 10 cm (3.9 in.) to the bottom of the printer.
In addition to space considerations, always heed the following precautions when finding a place to 
locate the printer:
❏Place the printer where you can easily unplug the power cord.
 
						

							Cleaning and Transporting the Printer74
❏Keep the entire computer and printer system away from potential sources of interference, such 
as loudspeakers or the base units of cordless telephones.
❏Avoid using an electrical outlet that is controlled by wall switches or automatic timers. 
Accidental disruption of power can erase valuable information in your computer’s and 
printer’s memory.
c
Caution:
❏Leave adequate room around the printer to allow for sufficient ventilation.
❏Avoid locations that are subject to direct sunlight, excessive heat, moisture, or dust.
❏Avoid using outlets that other appliances are plugged into.
❏Use a grounded outlet that matches the printer’s power plug. Do not use an adapter plug.
❏Only use an outlet that meets the power requirements for this printer.
For long distances
Repacking the printer
If you need to transport your printer for long distances, carefully repack it using the original box 
and packing materials.
1. Turn off the printer and remove the following items:
❏Power cord
❏Interface cables
❏Loaded paper
❏Toner cartridge
❏Developer unit
❏Installed options
c
Caution:
Do not remove the photoconductor unit. If you carry the printer without the photoconductor unit 
installed, the printer may be damaged.
2. Attach the protective materials onto the printer, then repack the printer in its original box.
c
Caution:
When moving the printer, always keep it horizontal.
 
						

							Cleaning and Transporting the Printer75
For short distances
Always pay attention to the following handling precautions when you need to move the printer for 
short distances.
1. Turn off the printer and remove the following items:
❏Power cord
❏Interface cables
❏Loaded Paper
❏Installed options
2. Be sure to lift the printer by the correct positions as shown below.
c
Caution:
When moving the printer, always keep it horizontal.
 
						

							Troubleshooting76
Chapter 6 
Troubleshooting
Clearing Jammed Paper
If paper becomes jammed in the printer, the EPSON Status Monitor provides alert messages.
Precautions for clearing jammed paper
Be sure to observe the following points when you clear jammed paper.
❏Do not remove jammed paper by force. Torn paper can be difficult to remove and might cause 
other paper jams. Pull it gently in order to avoid tearing.
❏Always try to remove jammed paper with both hands to avoid tearing it.
❏If jammed paper is torn and remains in the printer, or if paper is jammed in a place not 
mentioned in this section, contact your dealer.
❏Make sure that the paper type that is loaded is the same as the Paper Type setting in the printer 
driver.
❏Do not expose the photoconductor unit to sunlight at all.
w
Warning:
❏Be careful not to touch the fuser, which is marked CAUTION HOT SURFACE, or the 
surrounding areas. If the printer has been in use, the fuser and the surrounding areas may be very 
hot.
❏Do not insert your hand deep into the fuser unit as some components are sharp and may cause 
injury.
 
						

							Troubleshooting77
Paper Jam around the standard lower cassette
1. Remove the standard paper cassette, gently pull any sheets of paper out, and reinstall the paper 
cassette.
Paper Jam around the 250-sheet Paper Cassette Unit
1. Remove the optional paper cassette, gently pull any sheets of paper out, and reinstall the paper 
cassette.
 
						

							Troubleshooting78
2. Remove the standard paper cassette, gently pull any sheets of paper out, and reinstall the paper 
cassette.
Paper Jam in the 250-sheet Paper Cassette Unit
1. Remove the optional paper cassettes from the bottom one, then gently pull any sheets of paper 
out.
 
						

							Troubleshooting79
2. Reinstall the paper cassettes.
Paper Jam inside the printer
1. Open the top cover and MP tray.
2. Remove the developer unit containing the toner cartridge.
 
						

							Troubleshooting80
3. Put your finger into the hole of the outer green knob on each side of the photoconductor unit. 
Then, pull the photoconductor unit towards you.
w
Warning:
Be careful not to touch the fuser, which is marked CAUTION HOT SURFACE, or the 
surrounding areas. If the printer has been in use, the fuser and the surrounding areas may be very 
hot. If you must touch one of these areas, wait 30 minutes to allow the heat to subside before doing 
so.