Epson Aculaser M2010D User Manual

							Installing Options61
3. Remove the option cover.
4. Identify the memory slot. The position is shown below.
a. memory slot
5. Push a white stopper until it stops.
 
						

							Installing Options62
6. Insert the memory module into the memory slot until it stops.
7. Slide the white stopper back toward you to lock the memory module.
c
Caution:
❏Do not apply too much force.
❏Be sure to insert the memory facing the correct way.
❏Do not remove any modules from the circuit board. Otherwise, the printer will not work.
8. Reattach the option cover.
9. Tighten the screw on the option cover using the screw driver.
10. Reconnect all the interface cables and the power cord.
11. Plug the printer’s power cord into an electrical outlet.
12. Turn on the printer.
To confirm that the option is installed correctly, print a Status Sheet. See “Printing a Status Sheet” 
on page 90.
 
						

							Installing Options63
Note for Windows users:
If EPSON Status Monitor is not installed, you have to make settings manually in the printer driver. See 
“Making Optional Settings” on page 113.
Note for Macintosh users:
When you have attached or removed printer options, you need to delete the printer using Print Setup 
Utility (for Mac OS X 10.3 and 10.4), Print Center (for Mac OS X 10.2), and then re-register the printer.
Removing a memory module
w
Warning:
Be careful when working inside the printer as some components are sharp and may cause injury.
c
Caution:
Before you remove a memory module, be sure to discharge any static electricity by touching a grounded 
piece of metal. Otherwise, you may damage static-sensitive components.
Perform the installation procedure in reverse.
 
						

							Replacing Consumable Products64
Chapter 4 
Replacing Consumable Products
Precautions During Replacement
Always observe the following handling precautions when replacing consumable products:
For details about the replacement, see the instructions on the package.
❏Provide enough space for the replacement procedure. You will have to open some parts (such 
as the printer cover) of the printer when you are replacing consumables.
❏Do not install the consumable products that reach end of service life into the printer.
w
Warning:
❏Be careful not to touch the fuser, which is marked CAUTION HOT SURFACE, or the 
surrounding areas. If the printer has been in use, the fuser and surrounding areas may be very hot.
❏Do not dispose of used consumable products in fire, as they may explode and cause injury. Dispose 
of them according to local regulations.
Precautions for Replacing the Toner Cartridge
When the Toner light and the Error light are on, the printer has run out of toner. If the indicator 
lights light up in this manner, or if a message is displayed on the EPSON Status Monitor screen, 
replace the toner cartridge.
Always observe the following handling precautions when replacing the consumable products:
❏Installing a genuine consumable product is recommended. Using a non-genuine consumable 
product may affect print quality. EPSON shall not be liable for any damages or problems 
arising from the use of consumable products not manufactured or approved by EPSON.
❏When handling a toner cartridge, always place them on a clean, smooth surface.
❏If you move a toner cartridge from a cool to a warm environment, wait for at least one hour 
before installing it to prevent damage from condensation.
❏Do not expose the toner cartridge to room light any longer than necessary.
 
						

							Replacing Consumable Products65
❏The toner cartridge is not an independent unit that you install directly into the printer. The 
cartridge needs to be inserted into the developer unit’s casing and then installed into the 
printer.
w
Warning:
❏Do not touch the toner. Always keep toner away from your eyes. If toner gets on your skin or 
clothes, wash it off with soap and water immediately.
❏Keep consumable products out of the reach of children.
❏Do not dispose of used consumable products in fire, as they may explode and cause injury. Dispose 
of them according to local regulations.
❏If toner is spilled, use a broom and dustpan or a damp cloth with soap and water to clean it up. 
Because the fine particles can cause a fire or explosion if they come into contact with a spark, do 
not use a vacuum cleaner.
❏Be careful not to touch the fuser, which is marked CAUTION HOT SURFACE, or surrounding 
areas. If the printer has been in use, the fuser and the surrounding areas may be very hot. If you 
must touch one of these areas, wait 30 minutes to allow the heat subside before doing so.
 
						

							Replacing Consumable Products66
c
Caution:
❏You must completely open the printer cover when replacing the toner cartridge; otherwise, you 
may damage the printer.
❏Never touch the developing roller that is exposed after removing the protective cover; otherwise, 
print quality may decline.
❏When you replace the toner cartridge, wipe paper dust and marks from the metal roller inside the 
printer with a dry and soft cloth as shown below.
* metal roller
 
						

							Cleaning and Transporting the Printer67
Chapter 5 
Cleaning and Transporting the Printer
Cleaning the Printer
The printer needs only minimal cleaning. If the printer’s outer case is dirty or dusty, turn off the 
printer and clean it with a soft, clean cloth moistened with a mild detergent.
c
Caution:
Never use alcohol or paint thinner to clean the printer cover. These chemicals can damage the 
components and the case. Be careful not to get water onto the printer mechanism or any electrical 
components.
Cleaning the pickup roller
1. Turn off the printer.
*OFF
 
						

							Cleaning and Transporting the Printer68
2. Pull the paper cassette unit out and remove the papers.
3. Gently wipe the rubber parts of the pickup roller inside the printer with a well-wrung wet 
cloth.
4. Load the papers back on the paper cassette unit and reinstall the cassette.
 
						

							Cleaning and Transporting the Printer69
Cleaning inside the printer
1. Open the top cover and MP tray.
2. Remove the developer unit containing the toner cartridge.
3. Put your finger into the hole of the outer green knob on each side of the photoconductor unit. 
Then, pull the photoconductor unit towards you.
 
						

							Cleaning and Transporting the Printer70
w
Warning:
Be careful not to touch the fuser, which is marked CAUTION HOT SURFACE, or the 
surrounding areas. If the printer has been in use, the fuser and the surrounding areas may be very 
hot. If you must touch one of these areas, wait 30 minutes to allow the heat to subside before doing 
so.
c
Caution:
❏Never touch the developing roller that is exposed after removing the protecting cover; 
otherwise, print quality may decline.
❏Do not expose the photoconductor unit to room light any longer than necessary.
❏Never touch the photoconductor unit’s light-sensitive drum; otherwise, print quality may 
decline.