Epson AcuLaser M2000D User Manual

							For a Windows 2000 print server, select Shared as, then type the name in the Share Name box.
4. Select the additional drivers.
Note:
If the computers of the server and clients use the same OS, you do not have to install the
additional drivers. Just click OK after step3.
On the Windows XP, XP x64, or 2000 print server
Click Additional Drivers.
Select Windows being used for clients, then click OK.
Server Name Client OS Driver
Windows 2000 Windows XP or 2000 clients Intel Windows 2000
Windows XP
*Windows XP or 2000 clients Intel Windows 2000 or XP
Windows XP x64 clients x64 Windows XP
EPSON AcuLaser M1200 Series     User’s Guide
Setting Up Your Printer on a Network (AcuLaser M1200)     61
 
						

							Server Name Client OS Driver
Windows XP x64
*Windows XP or 2000 clients x86 Windows 2000, Windows XP
and Windows Server 2003
Windows XP x64 clients x64 Windows XP and Windows
Server 2003
Windows Vista or Vista x64 Windows Vista, XP, or 2000 clients x86 Type 3 - User Mode
Windows Vista x64 or XP x64 clients x64 Type 3 - User Mode
*The additional driver for Windows XP x64 can be used on Windows XP Service Pack2 or later.
Note:
❏You do not have to install the additional drivers noted below, because these drivers are
preinstalled. 
Intel Windows 2000 (for Windows 2000)
Intel Windows 2000 or XP (for Windows XP)
x64 Windows XP and Windows Server 2003 (for Windows XP x64)
x86 Type 3 - User Mode (for Windows Vista, XP, or 2000)
x64 Type 3 - User Mode (for Windows Vista x64 or XP x64)
❏Do not select additional drivers other than the drivers listed in the above table. The other
additional drivers are not available.
Setting up clients
This section describes how to install the printer driver by accessing the shared printer on a network.
EPSON AcuLaser M1200 Series     User’s Guide
Setting Up Your Printer on a Network (AcuLaser M1200)     62
 
						

							Note:
❏To share the printer on a Windows network, you need to set the print server. For details, see
“Using an additional driver” on page 59.
❏This section describes how to access the shared printer on a standard network system using the
server (Microsoft workgroup). If you cannot access the shared printer due to the network system,
ask the administrator of the network for assistance.
❏This section describes how to install the printer driver by accessing the shared printer from the
Printers folder. You can also access the shared printer from Network, Network Neighborhood, or
My Network on the Windows desktop.
❏You cannot use the additional driver on the server system OS.
❏When you want to use EPSON Status Monitor 3 at a client, you have to install EPSON Status
Monitor 3 from the CD-ROM with administrator privileges in each client.
❏For Windows Vista, if you want to monitor a shared printer with several users on a client
computer, select the Allow monitoring of the shared printers check box in EPSON Status
Monitor 3.
With Windows Vista, Vista x64, XP, XP x64, or 2000
Follow the steps below to set Windows Vista, Vista x64, XP, XP x64, or 2000 clients.
You can install the printer driver for the shared printer, if you have Power Users or more powerful
access rights even if you are not the Administrator.
For Windows Vista or Vista x64, even if you are not an administrator or power user, you can
install the printer driver by clicking Continue when the prompt to continue the installation appears.
Note:
The illustrations in this section show Windows XP screens. They may be different from the screens
for your operating system.
1. For Windows 2000 clients, click Start, point to Settings, and click Printers.
For Windows XP or XP x64 clients, click Start, point to Printers and Faxes.
For Windows Vista or Vista x64 clients, click 
 Start, click Control Panel, then double-click
Printers.
EPSON AcuLaser M1200 Series     User’s Guide
Setting Up Your Printer on a Network (AcuLaser M1200)     63
 
						

							2. For Windows 2000, double-click the Add Printer icon, then click Next.
For Windows XP or XP x64 click Add a printer in the Printer Tasks menu.
For Windows Vista or Vista x64, click Add a printer in the menu bar.
3. For Windows 2000, select Network printer, then click Next.
For Windows XP or XP x64, select A network printer, or a printer attached to another
computer, then click Next.
For Windows Vista or Vista x64, click Add a network, wireless or Bluetooth printer. If the
shared printer is found automatically, proceed to step 5. If not, click stop and click The
printer that I want isn’t listed, then go to step 4.
4. For Windows 2000, type the name of the shared printer, then click Next.
Note:
❏You can also type “\\(the name of the computer that is locally connected to the shared
printer)\(the shared printer’s name)” in network path or queue name.
❏You do not necessarily need to type the name of the shared printer.
EPSON AcuLaser M1200 Series     User’s Guide
Setting Up Your Printer on a Network (AcuLaser M1200)     64
 
						

							For Windows XP or XP x64, select Browse for a printer.
For Windows Vista or Vista x64, click Select a shared printer by name in the dialog box
that appears, then click Next.
5. For Windows XP, XP x64, or 2000, click the icon of the computer or server that is connected to
the shared printer, and the name of the shared printer, then click Next.
Note for Windows Vista users:
When the dialog box to enter user name and password appears, enter the information about the
print server, then click the name of the shared printer. When the Add Printer dialog box appears,
click Next.
EPSON AcuLaser M1200 Series     User’s Guide
Setting Up Your Printer on a Network (AcuLaser M1200)     65
 
						

							Note:
❏The name of the shared printer may be changed by the computer or server that is connected
to the shared printer. To make sure of the name of the shared printer, ask the administrator
of the network.
❏If the printer driver is installed in the client beforehand, you need to select either the new
printer driver or the current printer driver. When the prompt to select the printer driver
appears, select the printer driver according to the message.
❏If the additional driver for the corresponding Windows is installed in the print server, go to
the next step.
6. Select whether to use the printer as the default printer or not, then click Next.
7. Make sure of the settings, then click Finish.
Installing the printer driver from the CD-ROM
This section describes how to install the printer driver in the clients when setting the network
system without installing the additional drivers in the print server.
The on-screen displays on the following pages may differ depending on the version of Windows OS.
Note:
❏When installing in Windows XP, XP x64, or 2000 clients, you must access Windows XP, XP x64,
or 2000 as the Administrator.
❏For Windows Vista or Vista x64, even if you are not an administrator or power user, you can
install the printer driver by clicking Continue when the prompt to continue the installation appears.
EPSON AcuLaser M1200 Series     User’s Guide
Setting Up Your Printer on a Network (AcuLaser M1200)     66
 
						

							❏If the additional drivers are installed or the computers of the server and clients use the same OS,
you do not have to install the printer drivers from the CD-ROM.
1. Access the shared printer and a prompt may appear. Click OK, then follow the on-screen
instructions to install the printer driver from the CD-ROM.
2. Insert the CD-ROM, type the appropriate drive and folder names in which the printer driver
for clients is located, then click OK.
When installing drivers, “Digital Signature is not found.” may appear. Click Yes (for Windows
2000) or Continue Anyway (for Windows Vista, Vista x64, XP, or XP x64) and continue
installing.
The folder name differs depending on the OS being used.
Client’s OS Folder Name
Windows Vista, XP, or 2000\\WINVISTA_XP_2K
Windows Vista x64 or XP x64 \\VISTA_XP64
3. Select the name of the printer, click OK, then follow the on-screen instructions.
For Macintosh Users
Sharing the Printer
This section describes how to share the printer on an AppleTalk network.
EPSON AcuLaser M1200 Series     User’s Guide
Setting Up Your Printer on a Network (AcuLaser M1200)     67
 
						

							The computers on the network can share the printer that is directly connected to one of them. The
computer that is directly connected to the printer is the print server, and the other computers are
the clients which need permission to share the printer with the print server. The clients share the
printer via the print server.
For Mac OS X users
Use the Printer Sharing setting, which is a standard feature of Mac OS X 10.2 or later.
See your operating system’s documentation for details.
EPSON AcuLaser M1200 Series     User’s Guide
Setting Up Your Printer on a Network (AcuLaser M1200)     68
 
						

							Chapter 6
Replacing Consumable Products
Precautions During Replacement
Always observe the following handling precautions when replacing consumable products:
❏Provide enough space for the replacement procedure. You will have to open some parts (such
as the printer cover) of the printer when you are replacing consumables.
❏Do not install used consumable products into the printer.
w
Warning:
❏Be careful not to touch the fuser, which is marked CAUTION Hot Surface, or the
surrounding areas. If the printer has been in use, the fuser and surrounding areas may be
very hot.
❏Do not dispose of used consumable products in fire, as they may explode and cause injury.
Dispose of them according to local regulations.
Developer Cartridge
You need to replace the developer cartridge when a notice message is displayed on the window of
the EPSON Status Monitor 3.
When the Toner light is on and the Error light is flashing slowly on the EPL-6200 or the Ready
light is on and the Error light is flashing on the AcuLaser M1200/EPL-6200L, the printer has run
out of toner. If the indicator lights light up in this manner, or if a message is displayed on the
EPSON Status Monitor 3 screen, replace the developer cartridge.
Always observe the following handling precautions when replacing developer cartridges:
❏Installing a genuine consumable product is recommended. Using a non-genuine consumable
product may affect print quality. Epson shall not be liable for any damages or problems arising
from the use of consumable products not manufactured or approved by Epson.
❏When handling developer cartridges, always place them on a clean, smooth surface.
EPSON AcuLaser M1200 Series     User’s Guide
Replacing Consumable Products     69
 
						

							❏If you move a developer cartridge from a cool to a warm environment, wait for at least one
hour before installing it to prevent damage from condensation.
w
Warning:
❏Do not touch the toner in developer cartridges. Always keep toner away from your eyes. If
toner gets on your skin or clothes, wash it off with soap and water immediately.
❏Keep developer cartridges out of the reach of children.
❏Do not dispose of used developer cartridges in fire, as they may explode and cause injury.
Dispose of them according to local regulations.
❏If toner is spilled, use a broom and dustpan or a damp cloth with soap and water to clean it
up. Because the fine particles can cause a fire or explosion if they come into contact with a
spark, do not use a vacuum cleaner.
Replacing the developer cartridge
Follow these steps to replace the developer cartridge:
Note:
❏The developer cartridge is not an independent unit that you install directly into the printer. The
cartridge needs to be inserted into the photoconductor unit’s casing and then installed into the
printer.
❏The illustrations used in this procedure show the EPL-6200.
1. Lower the printer’s output tray.
EPSON AcuLaser M1200 Series     User’s Guide
Replacing Consumable Products     70