Epson AcuLaser CX21NC User Manual

							Using the PostScript Printer Driver121
❏On the Device Settings sheet of the printer’s Properties dialog box, make sure that 
SEND CTRL-D Before Each Job and SEND CTRL-D After Each Job are set to No.
❏TBCP (Tagged binary communications protocol) cannot be used as the Output 
Protocol setting.
❏On the Job Settings sheet of the printer’s Properties dialog box, make sure to clear the 
Job Management On check box.
Using the PostScript Printer Driver with Macintosh
Installing the PostScript printer driver 
Follow the steps below to install the PostScript printer driver.
Note:
Make sure that no applications are running on your Macintosh before installing the printer driver.
For Mac OS X users
Note:
Make sure that Printer Setup Utility (for Mac OS X 10.3 and 10.4) or Print Center (for Mac OS X 
10.2) is not open.
1. Insert the printer software CD-ROM into your CD-ROM drive.
2. Double-click the CD-ROM icon.
3. Double-click Mac OS X, then double-click PS Installer.
Note:
For Mac OS X 10.2, if the Authenticate window appears, enter the user name and password for 
an administrator.
4. The Install EPSON PostScript Software screen appears, click Continue, then follow 
the on-screen instructions.
5. Easy Install is displayed on the screen. Click Install.
Note:
For Mac OS X 10.3 and 10.4, if the Authenticate window appears, enter the user name and 
password for an administrator.
6. When installation is done, click Close.
 
						

							Using the PostScript Printer Driver122
Selecting the printer
After installing the PostScript 3 printer driver, you need to select the printer.
Selecting a printer in a network environment
If the printer is connected through the Ethernet interface or an optional network card.
For Mac OS X users
Follow the steps below to select the printer.
Note:
❏You cannot use FireWire for printer connection in the PostScript 3 mode. Although EPSON 
FireWire appears in the interface pop-up list, it cannot be used with the PostScript 3 printer 
driver.
❏You need to make the settings for your installed options manually when the printer is connected 
using USB, IP printing, or Bonjour (Rendezvous). When the printer is connected using 
AppleTalk, the printer software automatically makes the settings.
❏Make sure to specify ASCII as the data format in the application.
1. Open the Applications folder, open the Utilities folder, then double-click Printer 
Setup Utility (for Mac OS X 10.3 and 10.4) or Print Center (for Mac OS X 10.2).
The Printer List window appears.
2. Click Add in the Printer List window.
3. Select the protocol or the interface that you are using from the pop-up list.
Note for Appletalk users:
Make sure to select AppleTalk. Do not select EPSON AppleTalk, because it cannot be used 
with the PostScript 3 printer driver.
Note for IP Printing users:
❏Make sure to select IP Printing. Do not select EPSON TCP/IP, because it cannot be used 
with the PostScript 3 printer driver.
❏After selecting IP Printing, enter the IP address for the printer, then make sure to select the 
Use default queue on server check box.
Note for USB users:
Make sure to select USB. Do not select EPSON USB, because it cannot be used with the 
PostScript 3 printer driver.
4. Follow the instructions as appropriate below to select your printer.
 
						

							Using the PostScript Printer Driver123
AppleTalk
Select your printer from the Name List, then select Auto Select from the Printer Model 
List.
IP Printing
Select Epson from the Name List, then select your printer from the Printer Model List.
USB
Select your printer from the Name List, then select your printer from the Printer Model 
List.
Note for Mac OS X 10.3 and 10.4 users:
If ESC/Page driver is not installed, your printer model is automatically selected in the Printer 
Model List when you select your printer from the Name List while the printer is on.
Bonjour (Rendezvous)
Select your printer, the printer name is followed by (PostScript), from the Name List. 
Your printer model is automatically selected in the Printer Model List.
Note for USB (for Mac OS X 10.2) or Bonjour (Rendezvous) users:
If your printer model is not automatically selected in the Printer Model list, you need to reinstall 
the PostScript printer driver. See Installing the PostScript printer driver on page 121.
5. Click Add. 
Note for IP Printing users, USB or Bonjour (Rendezvous) users:
Select your printer from the Printer list, then select Show Info from the Printers menu. The 
Printer Info dialog box appears. Select Installable Options from the pop-up list, then make the 
necessary settings.
6. Confirm that your printer’s name is added to the Printer List. Then quit Printer Setup 
Utility (for Mac OS X 10.3 and 10.4) or Print Center (for Mac OS X 10.2).
Accessing the PostScript printer driver
To control your printer and change its settings, use the printer driver. The printer driver 
allows you to easily make all the print settings, including paper source, paper size, and 
orientation.
For Mac OS X users
To access the PostScript printer driver, register your printer in Printer Setup Utility (for 
Mac OS X 10.3 and 10.4) or Print Center (for Mac OS X 10.2), click Print on the file menu 
of any application, then select your printer.
 
						

							Using the PostScript Printer Driver124
Making changes to PostScript printer settings
You can change the PostScript printer settings in the PostScript printer driver. Balloon help 
is available to help you with the printer driver settings.
Using Balloon Help
Follow the steps below to use Balloon Help.
1. Click the Help menu, then select Show Balloons.
2. Place your cursor over the item that you need help with. Information on that item is 
displayed inside a floating balloon.
Changing the printer setup settings
You can change or update the printer setup settings according to the options installed in 
your printer.
For Mac OS X users
Follow the steps below to change the settings.
1. Access the printer driver. The Printer List window appears.
2. Select the printer from the list.
3. Select Show Info from the Printers menu. The Printer Info dialog box appears.
4. Make necessary changes to the settings, then close the dialog box.
5. Quit Printer Setup Utility (for Mac OS X 10.3 and 10.4) or Print Center (for Mac OS X 
10.2).
 
						

							Using the PCL6/PCL5 Printer Driver125
Chapter 7 
Using the PCL6/PCL5 Printer Driver
About the PCL Mode
Hardware requirements
Your printer must meet the following hardware requirements to be able to use the 
PCL6/PCL5 printer driver.
Memory requirements for using the PCL6/PCL5 printer driver are shown below. Install 
optional memory modules into your printer if the amount of memory currently installed does 
not meet your printing needs.
* Printing may not be possible with this amount of memory, depending on the specifics of the job being 
printed.
System requirements
Your computer must meet the following system requirements to be able to use the 
PCL6/PCL5 printer driver.
To use the PCL6/PCL5 printer driver, your computer must be running Microsoft Windows 
XP or have installed the 2000 Service Pack 3 or later.
For Windows XP or 2000
Minimum memory Recommended memory
128 MB* (for a simple print job at 600 dpi) 256 MB* or more
Minimum Recommended
ComputerIBM PC series or IBM compatible with 
Pentium or higher CPUIBM PC series or IBM compatible with 
Pentium II or higher CPU
Hard Disk10-25 MB free (for driver installation)
Memory128 MB (256 MB for Server 2003) 256 MB
DisplaySuper VGA supporting 640×480 Super VGA supporting 800×600 or 
more
 
						

							Using the PCL6/PCL5 Printer Driver126
For Windows XP x64 or 2003 Server x64
Using the PCL6/PCL5 Printer Driver
To print in the PCL mode, you will have to install the printer driver. Consult the customer 
support in your region regarding how to get the printer driver.
Note:
The PCL6/PCL5 printer driver and EPSON Status Monitor cannot be used at the same time.
Minimum Recommended
ComputerIBM PC series or IBM compatible with Intel EM64T or AMD/64 CPU
Hard Disk10-25 MB free (for driver installation)
Memory256 MB 512 MB
DisplaySuper VGA supporting 640×480 Super VGA supporting 800×600 or 
more
 
						

							Scanning127
Chapter 8 
Scanning
About Scanning Mode
System Requirements
Make sure that your system meets the requirements in these sections before using it with 
your scanner.
Check your system to see which type of interface you are using. Then see the appropriate 
section for your system below.
 For Windows system
USB 2.0 ports
Note:
❏USB 2.0 is backward-compatible with USB 1.1.
❏Contact your software manufacturer to find out if their software works in Windows XP 
Professional x64 Edition.
System Microsoft Windows XP Home Edition, Professional, or Professional x64 Edition, or 
2000 Professional
(Operating systems upgraded from Windows Millennium Edition, 98, and 95 are 
not supported by the software.)
USB 2.0 Host Driver by Microsoft must be used.
Interface USB port (Type A) built into the main board
Display SVGA or higher resolution monitor
800 × 600, 16-bit (High Color) screen resolution or higher 
(Color and tone reproduction are subject to the display capability of your 
computer system, including the video card, display monitor, and software. See 
your system documentation for details.)
 
						

							Scanning128
USB 1.1 ports
Note:
Contact your software manufacturer to find out if their software works in Windows XP Professional 
x64 Edition.
 For Macintosh system
USB 2.0 ports
Note:
❏USB 2.0 is backward-compatible with USB 1.1.
❏Epson Scan does not support the UNIX File System (UFS) for Mac OS X. You must install 
Epson Scan on a disk or in a partition that does not use UFS.
USB 1.1 ports
System Microsoft Windows XP Home Edition, Professional, or Professional x64 Edition, 
Millennium Edition, 98 Second Edition, or 2000 Professional
(Operating systems upgraded from Windows 95 are not supported by the 
software.) 
The USB interface must be used in full speed mode.
Interface USB port (Type A) built into the main board
Display SVGA or higher resolution monitor
800 × 600, 16-bit (High Color) screen resolution or higher 
(Color and tone reproduction are subject to the display capability of your 
computer system, including the video card, display monitor, and software. See 
your system documentation for details.)
System Macintosh computers running Mac OS X 10.2.8 or later
Fast User Switching on Mac OS X 10.3 is not supported.
Interface Macintosh USB
Display Color monitor with 800× 600 screen resolution or higher, and 32,000 or more 
colors
(Color and tone reproduction are subject to the display capability of your 
computer system, including the video card, display monitor, and software. See 
your system documentation for details.)
System Macintosh computers running Mac OS X 10.2.8 or later
Fast User Switching on Mac OS X 10.3 is not supported.
Interface Macintosh USB
 
						

							Scanning129
Note:
Epson Scan does not support the UNIX File System (UFS) for Mac OS X. You must install Epson 
Scan on a disk or in a partition that does not use UFS.
Setting Your Originals
Before scanning a document, remember to respect the rights of copyright owners. Do not 
scan published text or images without first checking their copyright status.
Document table
When using the document table, set an original one sheet at a time.
c
Caution:
❏Do not place heavy objects on the glass surface of the document table. Also, do not press 
the glass surface with too much force.
❏To scan an original correctly, set the transportation lock on the left side of the document 
table in the   unlocked position. 
* Transportation lock
Display Color monitor with 800× 600 screen resolution or higher, and 32,000 or more 
colors
(Color and tone reproduction are subject to the display capability of your 
computer system, including the video card, display monitor, and software. See 
your system documentation for details.)
*
 
						

							Scanning130
1. Make sure the product is turned on, and then open the document cover gently.
2. Place an original on the document table, with the side to be scanned facing down.
Use the document guide strip to align the horizontal edge of the document.
Note:
❏The area with a width of maximum 1.5 mm from the horizontal edge and 1.5 mm from the 
vertical edge is not scanned.
1. Maximum unreadable area of 1.5 mm
2. Maximum unreadable area of 1.5 mm
2
1