Epson AcuLaser C9100 User Manual
Have a look at the manual Epson AcuLaser C9100 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1734 Epson manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Installing Options211 6 6 6 6 6 6 6 6 6 6 6 6 6. Plug the connection cable into both the socket on the HDD and that on the board as shown below. 7. Reattach the cover to the right side of the printer by inserting the three projections at the bottom of the cover to the notches on the printer, and then sliding the cover forward to firmly fit it to the printer. Make sure the projection at the top of the cover is inserted to the notch on the printer. 8. Secure the cover with the three screws.
212Installing Options 9. Reconnect the power cord and turn the printer on. To confirm that the Hard Disk Drive is installed correctly, prints a status sheet. See “Printing a Status Sheet” on page 276. If the drive is not listed on the status sheet, try reinstalling the drive. Make sure that the connector on the Hard Disk Drive is securely connected to the socket on the circuit board. Note for Windows users: If you are using Windows, and EPSON Status Monitor 3 is not installed, you have to make settings manually in the printer driver. See “Making Optional Settings” on page 83. Note for Macintosh users: When you have attached or removed printer options, you need to delete the printer using Print Setup Utility (for Mac OS X 10.3), Print Center (for Mac OS X 10.2 or below), or Chooser (for Mac OS 9), and then re-register the printer. Removing the Hard Disk Drive Follow the steps below to remove the Hard Disk Drive. c Caution: Before you remove the Hard Disk Drive, be sure to discharge any static electricity by touching a grounded piece of metal. Otherwise, you may damage static-sensitive components. w Warning: Be careful when working inside the printer as some components are sharp and may cause injury. 1. Turn the printer off and unplug the power cord. 2. Perform the installation procedure in reverse.
Installing Options213 6 6 6 6 6 6 6 6 6 6 6 6 Memory Module By installing a Dual In-line Memory Module (DIMM), you can increase printer memory up to 1,024 MB. You may want to add additional memory if you are having difficulty printing complex graphics. This printer has two memory slots, but one slot has a 128 MB DIMM already installed in it at the time of manufacture. To increase printer memory more than 640 MB, remove the original 128 MB DIMM first and then install two optional DIMMs. Note: The maximum expandable memory is 1,024 MB. Installing a memory module Follow the steps below to install an optional memory module. w Warning: Be careful when working inside the printer as some components are sharp and may cause injury. c Caution: Before you install a memory module, be sure to discharge any static electricity by touching a grounded piece of metal. Otherwise, you may damage static-sensitive components.
214Installing Options 1. Turn the printer off and unplug the power cord. 2. Remove the three screws from the cover on the right side of the printer. s
Installing Options215 6 6 6 6 6 6 6 6 6 6 6 6 3. Slide the cover backward. Then tilt it toward you and remove it. w Warning: When you open the right side cover, be careful not to touch the areas surrounding the caution label on the circuit board since the areas may be very hot. 4. Identify the expansion RAM slot. * Expansion RAM slot *
216Installing Options 5. Confirm that the notch on the expansion RAM module matches that of the socket. 6. Firmly insert the top edge of the RAM module into the socket until it stops. 7. Press the inserted RAM module until it clicks so that the whole module is fully installed.
Installing Options217 6 6 6 6 6 6 6 6 6 6 6 6 c Caution: ❏Do not force the memory module into the socket. ❏Be sure to insert the memory module in the correct direction. 8. Reattach the cover to the right of the printer by inserting the three projections at the bottom of the cover to the notches on the printer, and then sliding the cover forward to firmly fit it to the printer. Make sure the projection at the top of the cover is inserted to the notch on the printer. 9. Secure the cover with the three screws. 10. Reconnect the power cord and turn the printer on.
218Installing Options To confirm that the memory module is installed correctly, print a status sheet. See “Printing a Status Sheet” on page 276 for instructions. If the total amount of memory listed does not include the size of the optional memory module, try reinstalling the module. Make sure that the module is securely seated into the memory slot on the circuit board. Note for Windows users: If you are using Windows, and EPSON Status Monitor 3 is not installed, you have to make settings manually in the printer driver. See “Making Optional Settings” on page 83. Note for Macintosh users: When you have attached or removed printer options, you need to delete the printer using Print Setup Utility (for Mac OS X 10.3), Print Center (for Mac OS X 10.2 or below), or Chooser (for Mac OS 9), and then re-register the printer. Removing a memory module Follow the steps below to remove a memory module. c Caution: Before you remove a memory module, be sure to discharge any static electricity by touching a grounded piece of metal. Otherwise, you may damage static-sensitive components. w Warning: Be careful when working inside the printer as some components are sharp and may cause injury. 1. Turn the printer off and unplug the power cord. 2. Perform the installation procedure in reverse.
Installing Options219 6 6 6 6 6 6 6 6 6 6 6 6 Adobe PostScript 3 Kit/P5C Emulation Kit The Adobe PostScript 3 Kit ROM module and P5C Emulation kit are available as an option for this printer. These modules allow your printer to print documents in the PostScript printing language and in the PCL5c printing language. Note: The features provided by the Adobe PostScript 3 ROM Module cannot be used when the printer is connected to a Macintosh computer using an optional IEEE 1394 Type B Interface Card. Installing the ROM Module c Caution: Before you install the ROM module, be sure to discharge any static electricity by touching a grounded piece of metal. Otherwise, you may damage static-sensitive components. w Warning: Be careful when working inside the printer as some components are sharp and may cause injury.
220Installing Options 1. Turn the printer off and unplug the power cord. 2. Remove the three screws from the cover on the right side of the printer. s