Home > Epson > Printer > Epson AcuLaser C4200DNPC6 User Manual

Epson AcuLaser C4200DNPC6 User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Epson AcuLaser C4200DNPC6 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1734 Epson manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    Page
    of 475
    							
    Using the Control Panel251
    7
    7
    7
    7
    7
    7
    7
    7
    7
    7
    7
    7
    To clear this error, select Clear Warning from the control panel’s 
    Reset Menu . For instruction about accessing the control panel 
    menus, see How to access the control panel menus on page 214.
    Duplex Mem Overflow
    There is not enough memory for duplex printing. The printer 
    prints only on the front and ejects the paper. To clear this error, 
    follow the instructions below.
    If  Off  is selected as the  Auto Cont setting on the control panel’s 
    Setup Menu , press the NStart/Stop  button to print on the back of 
    the next sheet, or press the  +Cancel Job  button to cancel the 
    print job.
    If  On  is selected as the  Auto Cont setting on the control panel’s 
    Setup Menu , printing continues automatically after a certain 
    period of time.
    Face-down Full
    The output paper at the face-down tray is full. Remove the paper 
    that has been output, then press the  NStart/Stop  button. Printing 
    resumes.
    Form Data Canceled
    Unable to store form overlay data on the printer’s optional Hard 
    Disk Drive. Either the drive is full, or the maximum number of 
    form overlay files has been reached. Delete any form overlay files 
    you no longer need, then try storing the new overlay again.
    To clear this error, select  Clear Warning from the control panel’s 
    Reset Menu . For instruction about accessing the control panel 
    menus, see How to access the control panel menus on page 214.
    Form Feed
     
    						
    							
    252Using the Control Panel
    The printer is ejecting paper due to a user request. This message 
    appears when pressing the 
    NStart/Stop  button once to make the 
    printer offline, then holding down the  NStart/Stop  button for 
    more than 2 seconds in order not to receive form feed command.
    Format Error ROM A
    An unformatted ROM module has been inserted. 
    To clear this error, either press the  NStart/Stop  button or turn off 
    the printer and remove the ROM module, then reinstall the ROM 
    module. If that fails to clear the error, contact your dealer.
    Formatting HDD
    The Hard Disk Drive is being formatted. 
    Hard Disk full
    The optional Hard Disk Drive is full and you cannot save any 
    data. Delete the unnecessary data from the Hard Disk Drive. To 
    clear this error, select  Clear Warning from the control panel’s 
    Reset Menu . For instruction about accessing the control panel 
    menus, see How to access the control panel menus on page 214.
    HDD CHECK
    The printer is checking the Hard Disk Drive.
    Image Optimum
    There is insufficient memory to print the page at the specified 
    print quality. The printer automatically lowers the print quality 
    so that it can continue printing. If the quality of the printout is not 
    acceptable, try simplifying the page by limiting the number of 
    graphics or reducing the number and size of fonts.
     
    						
    							
    Using the Control Panel253
    7
    7
    7
    7
    7
    7
    7
    7
    7
    7
    7
    7
    To clear this error, select Clear Warning from the control panel’s 
    Reset Menu. See How to access the control panel menus on page 
    214 for instructions.
    Turn the  Image Optimum  setting off on the control panel’s 
    Printing Menu  if you do not want the printer to automatically 
    lower the print quality to continue printing.
    You may need to increase the amount of printer memory to be 
    able to print at the desired print quality for your document. For 
    more information on adding memory, see Memory Module on 
    page 289.
    Install Fuser
    There is no fuser unit installed or the fuser unit is not installed 
    properly. Turn off the printer, then install the fuser unit if it is not 
    installed. 
    If a fuser unit is already installed, turn the printer off and reinstall 
    the unit after it has cooled off (30 minutes). Then open cover B. 
    Remove the fuser unit, then reinstall it properly. Close cover B. 
    The error clears automatically if the fuser unit is properly 
    installed. 
    If the error is not cleared, the fuser unit is out of order. Replace it 
    with a new fuser unit.
    Install LC1
    The paper tray of the standard paper cassette is not installed, or 
    not installed properly. Install the paper cassette correctly to clear 
    this error.
    Install LC2
    The paper tray of the optional 550-sheet paper cassette unit is not 
    installed, or not installed properly. Install the paper trays 
    correctly to clear this error.
     
    						
    							
    254Using the Control Panel
    Install LC3
    The paper trays of the optional 1100-sheet paper cassette unit are 
    not installed, or not installed properly. Install the paper trays 
    correctly to clear this error.
    Install Photoconductr
    There is no photoconductor unit installed or the photoconductor 
    unit is not installed properly. Turn off the printer and install the 
    photoconductor unit if it is not installed.
    If a photoconductor unit is already installed, confirm cover D is 
    closed. Otherwise, turn off the printer, open cover A, and then 
    open cover D. Remove the photoconductor unit, then reinstall it 
    properly. Close covers D and A. The error clears automatically if 
    the photoconductor unit is properly installed. 
    Install Transfer Unit
    There is no transfer unit installed or the transfer unit is not 
    installed properly. Turn off the printer, then install the transfer 
    unit if it is not installed. 
    If a transfer unit is already installed, turn off the printer, open 
    cover A, then remove the transfer unit. Reinstall the unit properly, 
    then close cover A. The error clears automatically if the transfer 
    unit is properly installed. 
    Install uuuu TnrCart
    The indicated toner cartridges are not installed in the printer. (The 
    l e t t e r s  C ,  M ,  Y ,  o r  K  a p p e a r  i n  p l a c e  o f  
    uuuu and indicate the colors 
    Cyan, Magenta, Yellow, and Black respectively.)
    Install the indicated cartridges. See Toner Cartridge on page 312.
    Invalid AUX I/F Card
     
    						
    							
    Using the Control Panel255
    7
    7
    7
    7
    7
    7
    7
    7
    7
    7
    7
    7
    This message means that the printer cannot communicate with 
    the installed optional interface card. Turn off the printer, remove 
    the card, then reinstall it.
    Invalid HDD
    Either the optional Hard Disk Drive is damaged or it cannot be 
    used with this printer. Turn off the printer, then remove the Hard 
    Disk Drive.
    Invalid N/W Module
    There is no network program, or the network program cannot be 
    used with your printer. Contact a qualified service representative.
    Invalid P5C
    A n  o p t i o n a l  P 5 C  E m u l a t i o n  K i t  t h a t  c a n n o t  b e  u s e d  o n  t h i s  p r i n t e r  
    is installed. Turn off the printer, then remove the module. 
    Invalid PS3
    The PostScript3 ROM module is broken. Turn off the printer and 
    contact your dealer.
    Invalid ROM A
    The printer cannot read the installed optional ROM module. Turn 
    off the printer, then remove the ROM module.
    Paper Jam WWWW
    The location where the paper jam occurred is displayed at WWWWW. 
    WWWWW  indicates the location of the error.
    If a paper jam occurs at two or more locations simultaneously, the 
    corresponding multiple locations are displayed.
     
    						
    							
    256Using the Control Panel
    LC3 Error 001
    Two 550-sheet paper cassette units are installed. Turn off the 
    printer and remove one of them from the printer.
    Manual Feed ssss
    The manual feed mode is specified for the current print job. Make 
    sure the paper size indicated by 
    ssss is loaded, then press the 
    N Start/Stop  button.
    Mem Overflow
    The printer has insufficient memory to execute the current task. 
    Press the  NStart/Stop  button on the control panel to resume 
    printing, or press the  +Cancel Job  button to cancel the print job.
    Menus Locked
    Location Description
    Paper 
    Jam AB Paper is jammed at the fuser unit. For instructions on how 
    to remove jammed paper at the fuser unit, see Paper 
    Jam A B on page 356.
    Paper 
    Jam A Paper is jammed at cover A. For instructions on how to 
    remove jammed paper at cover A, see Paper Jam A on 
    page 362.
    Paper 
    Jam CA Paper is jammed cover A and the paper cassette. For 
    instructions on how to remove jammed paper at the 
    Duplex Unit, see Paper Jam C A on page 367.
    Paper 
    Jam B Paper is jammed at cover B. For instructions on how to 
    remove jammed paper at the MP tray, see Paper Jam B 
    on page 375.
    Paper 
    Jam CAB Paper is jammed at cover A, B, the paper cassette. For 
    instructions on clearing this type of paper jam, see Paper 
    Jam C A B on page 376.
     
    						
    							
    Using the Control Panel257
    7
    7
    7
    7
    7
    7
    7
    7
    7
    7
    7
    7
    This message appears if you try to change the printer’s settings 
    through the control panel when the buttons are locked. You can 
    unlock them by using the Network utility. Refer to the Network 
    Guide  for information.
    Need Memory
    The printer has insufficient memory to complete the current print 
    job. 
    To clear this error message, select  Clear Warning from the control 
    panel’s  Reset Menu . SeeHow to access the control panel menus 
    on page 214 for instructions.
    To prevent this problem from happening again, add more 
    memory to your printer as described in Memory modules on 
    page 422, or reduce the resolution of the image to be printed.
    NonGenuine Toner
    The installed toner cartridge is not a genuine Epson product. 
    Installing a genuine toner cartridge is recommended. The 
    printout and remaining amount of each toner cartridge displayed 
    on the control panel may be different from those when using 
    genuine EPSON toner cartridges. Epson shall not be liable for any 
    damages or problems arising from the use of consumable 
    products not manufactured or approved by Epson.
    Install a genuine Epson product, or  Clear All Warnings of the 
    Reset Menu  on the control panel to clear the warning message. 
    See Toner Cartridge on page 312 for instructions on replacing 
    the imaging cartridge.
    NonGenuine Toner uuuu
     
    						
    							
    258Using the Control Panel
    The installed toner cartridge is not an genuine Epson toner 
    cartridge. The printout and remaining amount of each toner 
    cartridge displayed on the control panel may be different from 
    those when using genuine EPSON toner cartridges. Epson shall 
    not be liable for any damages or problems arising from the use of 
    consumable products not manufactured or approved by Epson. 
    Installing a genuine toner cartridge is recommended. Press the 
    N
    Start/Stop  button on the control panel to resume printing.
    Offline
    The printer is not ready to print. Press the  NStart/Stop  button.
    In this mode, the remaining amount of the toner cartridge for each 
    color is displayed in seven levels.
    Optional RAM Error
    The optional memory module may be corrupted or incorrect. 
    Replace it with a new one.
    Paper Out tttt sssss
    There is no paper in the specified paper source ( tttt). Load paper 
    of the size ( sssss) into the paper source.
    Paper Set tttt sssss
    The paper loaded in the specified paper source ( tttt) does not 
    match the required paper size ( sssss). Replace the loaded paper 
    with the correct size paper and press the  NStart/Stop  button to 
    resume printing, or press the  +Cancel Job  button to cancel the 
    print job.
    If you press the  NStart/Stop  button without replacing the paper, 
    the printer will print on the loaded paper even though it does not 
    match the required size.
    Printer Open
     
    						
    							
    Using the Control Panel259
    7
    7
    7
    7
    7
    7
    7
    7
    7
    7
    7
    7
    Cover A, cover B, cover D, or some combination of these covers 
    are open. To clear this error, close all covers.
    Print Overrun
    The required time to process the print data exceeded the print 
    engine speed because the current page is too complex. Press the 
    NStart/Stop  button to resume printing, or press the  +Cancel 
    Job  button to cancel the print job. If this message appears again, 
    select  On as the  Page Protect  setting in the control panel’s  Setup 
    Menu  or select  Avoid Page Error  on the printer driver.
    If you continue to receive this message when printing a particular 
    page, try simplifying the page by limiting the number of graphics 
    or reducing the number and size of fonts.
    To avoid this error, it is recommended that you set the  Page 
    Protect  setting to  On and add more memory to the printer. See 
    Setup Menu on page 224 and Memory Module on page 289 for 
    details.
    PS3 Hard Disk full
    The memory allocated for writing PostScript 3 commands on the 
    optional Hard Disk Drive is full.
    To clear this error, select  Clear Warning from the control panel’s 
    Reset Menu , or remove the downloaded PS fonts to make room 
    on the Hard Disk Drive. For instruction about accessing the 
    control panel menus, see How to access the control panel menus 
    on page 214.
    RAM check
    The printer is checking the RAM.
    Ready
     
    						
    							
    260Using the Control Panel
    The printer is ready to receive data and print.
    In this mode, the remaining amount of the toner cartridge for each 
    color is displayed in seven levels.
    Replace Photoconductor
    The photoconductor has reached the end of its service life. Turn 
    off the printer, then replace the photoconductor unit with a new 
    one. See Photoconductor Unit on page 318 for instructions.
    The error clears automatically after you replace the unit, then 
    close all printer covers. The photoconductor service life counter 
    is reset automatically.
    When the error light is blinking, you can continue printing by 
    pressing the 
    NStart/Stop  button. However, the print quality is 
    not guaranteed from then on.
    Replace Toner uuuu
    The indicated toner cartridges are out of toner and need to be 
    replaced. (The letters C, M, Y, or K appear in place of  uuuu and 
    indicate the colors Cyan, Magenta, Yellow, and Black 
    respectively.)
    See Toner Cartridge on page 312 for instructions.
    Replace Transfer Unit
    The transfer unit has reached the end of its service life. Turn off 
    the printer, then replace the transfer unit with a new one. See 
    Transfer Unit on page 330 for instructions.
    The error clears automatically after you replace the unit and close 
    all printer covers. The transfer unit service life counter is reset 
    automatically.
    Reserve JobCanceled
     
    						
    All Epson manuals Comments (0)

    Related Manuals for Epson AcuLaser C4200DNPC6 User Manual