Epson AcuLaser C4200DNPC6 User Manual

							
Using the Control Panel241
7
7
7
7
7
7
7
7
7
7
7
7
Selects the pitch (the horizontal spacing) of the font in fixed pitch, 
measured in cpi (characters per inch). You can also choose 
proportional spacing.
Condensed
Turns condensed printing on or off.
T. Margin
Sets the distance from the top of the page to the baseline of the 
first printable line. The distance is measured in inches. The 
smaller the value, the closer the printable line is to the top.
Text
Sets the page length in lines. For this option, a line is assumed to 
be 1 pica (1/6 inch). If you change the Orientation, Page Size, or 
T. Margin settings, the page length setting automatically returns 
to the default for each paper size.
CG Table
Use the character generator (CG) table option to select the 
graphics character table or the italics table. The graphics table 
contains graphic characters for printing lines, corners, shaded 
areas, international characters, Greek characters, and 
mathematical symbols. If you select Italic, the upper half of the 
character table is defined as italic characters.
Country
Use this option to select one of the fifteen international symbol 
sets. See International character sets on page 460 for samples of 
the characters in each country’s symbol set.
Auto CR
 
						

							
242Using the Control Panel
Specifies whether the printer performs a 
carriage-return/line-feed (CR-LF) operation whenever the 
printing position goes beyond the right margin. If you select 
Off, 
the printer does not print any characters beyond the right margin 
and does not perform any line wrapping until it receives a 
carriage-return character. This function is handled automatically 
by most applications.
Auto LF
If you select  Off, the printer does not send an automatic line-feed 
(LF) command with each carriage-return (CR). If  On is selected, a 
line-feed command is sent with each carriage-return. Select  On if 
your text lines overlap.
Bit Image
The printer is able to emulate the graphics densities set with the 
printer commands. If you select  Dark, the bit image density is 
high, and if you select  Light, the bit image density is low.
If you select  BarCode, the printer converts bit images to bar codes 
by automatically filling in any vertical gaps between dots. This 
produces unbroken vertical lines that can be read by a bar code 
reader. This mode will reduce the size of the image being printed, 
and may also cause some distortion when printing bit image 
graphics.
ZeroChar
Specifies whether the printer prints a slashed or unslashed zero.
FX Menu
Ne w  :Emulation
 onlyThis menu allows you to make settings which affect the printer 
when it is in the FX emulation mode.
 
						

							
Using the Control Panel243
7
7
7
7
7
7
7
7
7
7
7
7
* Depending on whether Letter (62) or A4 (66) paper has been selected.
Font
Selects the font.
Pitch
Selects the pitch (the horizontal spacing) of the font in fixed pitch, 
measured in cpi (characters per inch). You can also choose 
proportional spacing.
Condensed
Turns condensed printing on or off.
Item Settings (default in bold)
FontCourier, Prestige, Roman, Sans Serif, Script, 
Orator S, OCR A, OCR B
Pitch 10, 12, 15 cpi, Prop. 
Condensed Off, On
T. Margin 0.40 ...  0.50 ... 1.50 inches in 0.05-inch 
increments
Text 1...  62/66*... 132 lines
CGTable PcUSA, Italic, PcMultilin, PcPortugue, 
PcCanFrenc, PcNordic, PcTurkish2, 
PcIcelandic, PcE.Europe, BpBRASCII, 
BpAbicomp, Roman-8, PcEur858, ISO Latin1, 
8859-15ISO
Country USA, France, Germany, UK, Denmark, 
Sweden, Italy, Spain1, Japan, Norway, 
Denmark2, Spain2, LatinAmeric
Auto CR On, Off
Auto LF Off, On
Bit Image Dark, Light, BarCode
ZeroChar 0, (or the zero character with a slash)
 
						

							
244Using the Control Panel
T. Margin
Sets the distance from the top of the page to the baseline of the 
first printable line. The distance is measured in inches. The 
smaller the value, the closer the printable line is to the top.
Text
Sets the page length in lines. For this option, a line is assumed to 
be 1 pica (1/6 inch). If you change the Orientation, Page Size, or 
T. Margin settings, the page length setting automatically returns 
to the default for each paper size.
CG Table
Use the character generator (CG) table option to select the 
graphics character table or the italics table. The graphics table 
contains graphic characters for printing lines, corners, shaded 
areas, international characters, Greek characters, and 
mathematical symbols. If you select 
Italic, the upper half of the 
character table is defined as italic characters.
Country
Use this option to select one of the fifteen international symbol 
sets. See International character sets on page 460 for samples of 
the characters in each country’s symbol set.
Auto CR
Specifies whether the printer performs a 
carriage-return/line-feed (CR-LF) operation whenever the 
printing position goes beyond the right margin. If you select  Off, 
the printer does not print any characters beyond the right margin 
and does not perform any line wrapping until it receives a 
carriage-return character. This function is handled automatically 
by most applications.
Auto LF
 
						

							
Using the Control Panel245
7
7
7
7
7
7
7
7
7
7
7
7
If you select Off, the printer does not send an automatic line-feed 
(LF) command with each carriage-return (CR). If  On is selected, a 
line-feed command is sent with each carriage-return. Select  On if 
your text lines overlap.
Bit Image
The printer is able to emulate the graphics densities set with the 
printer commands. If you select  Dark, the bit image density is 
high, and if you select  Light, the bit image density is low.
If you select  BarCode, the printer converts bit images to bar codes 
by automatically filling in any vertical gaps between dots. This 
produces unbroken vertical lines that can be read by a bar code 
reader. This mode will reduce the size of the image being printed, 
and may also cause some distortion when printing bit image 
graphics.
ZeroChar
Selects whether the printer prints a slashed or unslashed zero.
I239X Menu
N ew :Emulation o nlyThe I239X mode emulates IBM® 2390/2391 Plus commands.
These settings are available only when the printer is in the I239X 
mode.
 
						

							
246Using the Control Panel
*1Depends on whether Letter (63) or A4 (67) paper has been selected.
*2Depends on whether Letter (1) or A4 (2) paper has been selected.
Font
Selects the font.
Pitch
Selects the pitch (the horizontal spacing) of the font in fixed pitch, 
measured in cpi (characters per inch). You can also choose 
proportional spacing.
Code Page
Selects the character tables. Character tables contain the 
characters and symbols used by different languages. The printer 
prints text based on the selected character table.
T. Margin
Item Settings (default in bold)
FontCourier, Prestige, Gothic, Orator, Script, 
Presentor, Sans Serif
Pitch 10, 12, 15, 17, 20, 24 cpi, Prop.
Code Page 437, 850, 858, 860, 863, 865
T. Margin 0.30 ...  0.40 ...1.50 inches in 0.05-inch 
increments
Text 1 ...  63/67
*1... 132 lines
Auto CR Off, On
Auto LF Off, On
Alt. Graphics Off, On
Bit Image Dark, Light
ZeroChar 0, (or the zero character with a slash)
CharacterSet 1
*1, 2*2
 
						

							
Using the Control Panel247
7
7
7
7
7
7
7
7
7
7
7
7
Sets the distance from the top of the page to the baseline of the 
first printable line. The distance is measured in inches. The 
smaller the value, the closer the printable line is to the top.
Text
Sets the page length in lines. For this option, a line is assumed to 
be 1 pica (1/6 inch). If you change the Orientation, Page Size, or 
T. Margin settings, the page length setting automatically returns 
to the default for each paper size.
Auto CR
Specifies whether the printer performs a 
carriage-return/line-feed (CR-LF) operation whenever the 
printing position goes beyond the right margin. If this setting is 
off, the printer does not print any characters beyond the right 
margin and does not perform any line wrapping until it receives 
a carriage-return character. This function is handled 
automatically by most applications.
Auto LF
If you select Off, the printer does not send an automatic line-feed 
(LF) command with each carriage-return (CR). If  On is selected, a 
line-feed command is sent with each carriage-return. Select  On if 
your text lines overlap.
Alt.Graphics
Turns the Alternate Graphics option on or off.
Bit Image
The printer is able to emulate the graphics densities set with the 
printer commands. If you select  Dark, the bit image density is 
high, and if you select  Light, the bit image density is low.
 
						

							
248Using the Control Panel
If you select 
BarCode, the printer converts bit images to bar codes 
by automatically filling in any vertical gaps between dots. This 
produces unbroken vertical lines that can be read by a bar code 
reader. This mode will reduce the size of the image being printed, 
and may also cause some distortion when printing bit image 
graphics.
ZeroChar
Selects whether the printer prints a slashed or unslashed zero.
CharacterSet
Selects character table 1 or 2.
Status and Error Messages
Ne w  :W ith
 LCD
 panel
 / c
onfirm t
he
 product
 s
pecification
 and d
elete
 unnecessary
 information /
use
 caution
 with t
he
 button
 or
 iconThis section contains a list of error messages shown on the LCD 
panel, giving a brief description of each message and suggestions 
for correcting the problem. Note that not every message shown 
on the LCD panel indicates a problem. When the   mark is 
displayed at the right of the warning message, multiple warnings 
occur. To confirm all warnings that occur, press the  dDown  
button to display the Status Menu, then press the  Enter button. 
The LCD panel also displays the amounts of remaining toners and 
available paper sizes.
Calibrating Printer
The printer automatically calibrates itself. This is not an error 
message, and will clear itself after the calibration process has 
finished. While the printer displays this message, do not open the 
covers or turn off the printer.
Cancel All Print Job
 
						

							
Using the Control Panel249
7
7
7
7
7
7
7
7
7
7
7
7
The printer is canceling all print jobs in the printer memory, 
including jobs the printer is currently receiving or printing. This 
message appears when the +Cancel Job  button has been 
pressed down for more than 2 seconds.
Cancel Print Job
The printer is canceling the current print job. This message 
appears when the  +Cancel Job  button has been pressed and 
released within 2 seconds.
Cancel Print Job (by host)
The print job is canceled at the printer driver.
Can’t Print
The print data is deleted because it is incorrect.
Make sure that the appropriate paper size is set and appropriate 
your printer driver is used.
Can’t Print Duplex
The printer has encountered problems during duplex printing. 
Make sure you are using an appropriate type and size of paper 
for the Duplex Unit. The problem could also be a result of 
incorrect settings for the paper source you are using. Pressing the 
N Start/Stop  button will print the rest of the print job on only one 
side of the paper. Press the  +Cancel Job  button to cancel the 
print job.
Check Transparency
You have loaded media other than transparencies when the Paper 
Type setting in the printer driver is  Transparency, or 
transparencies are loaded when the Paper Setting in the printer 
driver is not set to  Transparency. Paper is jammed at the MP tray. 
 
						

							
250Using the Control Panel
To clear the jam, see Paper Jam C A B on page 376.
Check Paper Size
The paper size setting is different from the size of paper loaded 
in the printer. Check to see if the 
correct size of paper is loaded in 
the specified paper source.
To clear this error, select  Clear Warning from the control panel’s 
Reset Menu . See How to access the control panel menus on page 
214 for instructions.
Check Paper Type
The paper loaded in the printer does not match the paper type 
setting in the printer driver. Paper that matches only the paper 
size setting will be used for printing.
To clear this error, select  Clear Warning from the control panel’s 
Reset Menu . See How to access the control panel menus on page 
214 for instructions.
Clean Sensor
Open cover A and remove the transfer unit temporarily. Wipe the 
transparent plastic window on the density sensor at the back of 
the transfer unit with a soft cloth, then reinstall the transfer unit. 
Close cover A to clear this error. 
If the error still remains, replace the transfer unit with a new one.
Collate Disabled
Printing by specifying the number of copies is no longer possible 
due to a lack of memory (RAM) or free disk space on the optional 
Hard Disk Drive. If this error occurs, print only one copy at a time.