Epson AcuLaser C4200DNPC6 User Manual

							
Using the Control Panel221
7
7
7
7
7
7
7
7
7
7
7
7
Emulation Menu
New :Emulation o
nly/ c
onfirm t
he
 product
 s
pecificationUse this menu to select the printer emulation mode. You can 
specify different emulations for each interface; in other words, for 
each computer you connect the printer to. Since each emulation 
mode has its own specific options, make settings in the ESC P2, 
FX, or I239X menu, as necessary. The settings you can choose from 
are the same for every interface.
*1 Available only when an optional Type-B interface card is installed.
*2 Available only when an optional P5C module is installed.
Printing Menu
New :c onfirm t
he
 product
 s
pecificationThis menu allows you to make standard print settings, such as 
Page Size and Orientation, when printing from an application or 
operating system that does not support your printer driver. Be 
sure to use the printer driver to make these settings whenever you 
can, since settings made on your computer always override these 
settings.
Item Settings (default in bold)
Parallel Auto, ESCP2, FX, I239X, PS3, P5C
*2
USB Auto, ESCP2, FX, I239X, PS3, P5C*2
Network Auto, ESCP2, FX, I239X, PS3, P5C*2
 AUX*1Auto, ESCP2, FX, I239X, PS3, P5C*2
 
						

							
222Using the Control Panel
*1 Custom-size paper is 88.9 × 139.7 mm at the minimum and 220  × 355.6 mm 
at the maximum, but EPSON recommends printing on paper that is not wider 
than 207.9 mm.
*2Not available in optional P5C mode.
Page Size
Specifies the paper size.
Wide A4
Selecting  On decreases the left and right margins from 4 mm to 
3.4 mm.
Orientation
Specifies whether the page is printed in portrait or landscape 
orientation.
Resolution
Item Settings (default in bold)
Page Size A4, B5, A5, LT, HLT, LGL, GLT, GLG, EXE, F4, DL, 
IB5, CTM
*1
Wide A4 Off, On
Orientation Port, Land
Resolution 300,  600, 1200
*2
RITech On, Off
Toner Save Off, On
Image Optimum Auto, Off, On
Top Offset -99.0 ...  0.0 ... 99.0 mm in 0.5 increments
LeftOffset -99.0 ...  0.0 ... 99.0 mm in 0.5 increments
T Offset B -99.0 ...  0.0 ... 99.0 mm in 0.5 increments
L Offset B -99.0 ...  0.0 ... 99.0 mm in 0.5 increments
 
						

							
Using the Control Panel223
7
7
7
7
7
7
7
7
7
7
7
7
Specifies the printing resolution.
RITech
Turning RITech on produces smoother and crisper lines, text, and 
graphics.
Toner Save
When this setting is selected, the printer saves toner by 
substituting a gray shade for the black inside of characters. The 
characters are outlined in full black on the right and lower edges.
Image Optimum
When this mode is on, the quality of graphics is reduced. It 
reduces the amount of graphics data when the data reaches the 
memory limit, allowing complex documents to be printed.
Top Offset
Makes fine adjustments to the vertical printing position of the 
page.
c
Caution:
Make sure that the printed image does not extend beyond the edge 
of the paper. Otherwise, you may damage the printer.
Left Offset
Makes fine adjustments to the horizontal printing position of the 
page. This is useful for fine adjustments.
c
Caution:
Make sure that the printed image does not extend beyond the edge 
of the paper. Otherwise, you may damage the printer.
T Offset B
 
						

							
224Using the Control Panel
Adjusts the vertical printing position on the back of the paper 
when printing on both sides. Use 
this if the printout on the back 
is not where you expected.
L Offset B
Adjusts the horizontal printing position on the back of the paper 
when printing on both sides. Use  this if the printout on the back 
is not where you expected.
Setup Menu
N ew :vary  according
 to
 the p
roduct
 /quote
 t
he
 information
 from
 the s
imilar
 productThis menu allows you to make various basic configuration 
settings related to paper sources, feeding modes, and error 
handling. You can also use this menu to select the LCD panel 
display language.
 
						

							
Using the Control Panel225
7
7
7
7
7
7
7
7
7
7
7
7
*1Available only when the optional paper cassette unit is installed.
*2Available only when you use A4, A5, B5, LT, LGL, EXE, or GLG size paper.
*3Available only for ESC/Page, ESC/P2, FX, or I239X mode.
*4Not available when an optional P5C module is installed.
Lang
Item Settings (default in bold)
LangEnglish, Français, Deutsch, Italiano, 
ESPAÑOL, SVENSKA, Dansk, Nederlands, 
SUOMI, Português, Norsk,  ,  , 
Time to Sleep 5, 15, 30,  60, 120, 180, 240 Min
Time Out 0, 5 to  60 to 300 in increments of 1
Paper Source Auto, MP, LC1, LC2
*1, LC3 *1, LC4*1
MP Mode Normal, Last
Manual Feed Off, 1st page, Each Page
Copies 1 to 999
Duplex
*2Off , On
Binding Long Edge, Short Edge
Start Page Front, Back
Paper Type Normal, SemiThk, Thick, ExtraThk, 
Transparency
Page Side Front, Back
Skip Blank Page
*3Off , On
Auto Eject Page Off, On
Size Ignore Off, On
Auto Cont Off, On
Page Protect
*4Auto , On
LCD Contrast 0 to  7 to 15
 
						

							
226Using the Control Panel
Specifies the language displayed on the LCD panel and that 
printed on the status sheet.
Time to Sleep
Specifies the length of time until the printer enters the sleep mode 
if there are no button operations.
Time Out
Specifies the length of the time, in seconds, before a time out when 
interfaces are being switched automatically. The time before a 
time out occurs is the length of time from the point when no data 
is being received from an interface until the point of switching the 
interface. If the printer has a print job when switching the 
interface, the printer prints the print job.
Paper Source
Specifies whether paper feeds into the printer from the MP tray 
or the optional lower paper cassette unit.
If you select 
Auto, paper feeds from the paper source containing 
paper that matches your Paper Size setting.
If an envelope size (DL, IB5) is selected as the Page Size setting, 
paper always feeds from the MP tray. If you select  Thick, 
ExtraThk , or Trnsprnc  as the Paper Type setting, paper always 
feeds from the MP tray.
MP Mode
This setting determines whether the MP tray has the highest or 
lowest priority when  Auto is selected as the Paper Source setting 
in the printer driver. When  Normal is selected as the MP Mode, 
the MP tray has the highest priority as the paper source. If you 
select  Last, the MP tray has the lowest priority.
Manual Feed
 
						

							
Using the Control Panel227
7
7
7
7
7
7
7
7
7
7
7
7
Allows you to select the manual feed mode for the MP tray.
Copies
Designates the number of copies to be printed, from 1 through 
999.
Duplex
Turns duplex printing on or off.
Binding
Specifies the binding direction of the printout.
Start Page
Specifies whether printing starts from the front or back of the 
page.
Paper Type
Specifies the type of paper to be used for printing. The printer 
adjusts the printing speed according to this setting. The printing 
speed is reduced when Thick, Extra Thk , or Trnsprnc  is selected.
Page Side
Select  Front when printing on the front of thick paper ( Thick) or 
extra-thick paper ( ExtraThk).
Select  Back when printing on the back of thick paper ( Thick) or 
extra-thick paper ( ExtraThk)
Skip Blank Page
Enables you to skip blank pages when printing. This setting is 
available when you print in the ESC/Page, ESCP2, FX, or I239X 
mode.
 
						

							
228Using the Control Panel
Auto Eject Page
Specifies whether or not to eject paper when the limit specified in 
the Time Out setting is reached. The default is 
Off, which means 
paper is not ejected when the time-out limit is reached.
Size Ignore
If you want to ignore a paper size error, select  On. When you turn 
this item on, the printer keeps printing even if the image size 
exceeds the printable area for the specified paper size. This may 
cause smudges because of the toner that is not transferred onto 
the paper properly. When this item is turned off, the printer stops 
printing if a paper size error occurs.
Auto Cont
When you turn this setting on, the printer automatically continues 
printing after a certain period of time when one of the following 
errors occurs: Paper Set, Print Overrun, or Mem Overflow. When 
this option is off, you must press the  NStart/Stop  button to 
resume printing.
Page Protect
Allocates additional printer memory for printing data, as 
opposed to receiving it. You may need to turn this setting on if 
you are printing a very complex page. If a  Print Overrun error 
message appears on the LCD panel during printing, turn this 
setting on and reprint your data. This reduces the amount of 
memory reserved for processing data so your computer may take 
longer to send the print job, but it will allow you to print complex 
jobs. Page Protect usually works best when  Auto is selected. You 
will need to increase your printer’s memory if memory errors 
continue to occur.
Note:
Changing the Page Protect setting  reconfigures the printer’s memory, 
which causes any downloaded fonts to be deleted.
 
						

							
Using the Control Panel229
7
7
7
7
7
7
7
7
7
7
7
7
LCD Contrast
Adjusts the contrast of the LCD panel. Use the uUp  and  dDown  
buttons to set the contrast between  0 (lowest contrast) and  15 
(highest contrast.)
Quick Print Job Menu
This menu allows you to print or delete print jobs that were stored 
in the printer’s Hard Disk Drive using the Quick Print Job feature 
(Re-Print Job, Verify Job, Stored Job) of the printer driver’s 
Reserve Job function. For instructions on using this menu, see 
Using the Quick Print Job Menu on page 265.
Confidential Job Menu
This menu allows you to print or delete print jobs stored in the 
printer’s Hard Disk Drive using the Confidential Job feature of 
the printer driver’s Reserve Job function. You need to enter the 
correct password to access this data. For instructions on using this 
menu, see Using the Confidential Job Menu on page 266.
Color Regist Menu
This menu allows you to make color registration settings.
Cyan Regist
Item Settings (default in bold)
Cyan Regist -36 ... 0 ... 36 in increments of 1
Magenta Regist -36 ... 0 ... 36 in increments of 1
Yellow Regist -36 ... 0 ... 36 in increments of 1
 
						

							
230Using the Control Panel
Adjusts the registration position of the color cyan relative to black.
To adjust the registration, select
 Color Regist Sheet on the 
control panel’s  Information Menu  to print a color registration 
sheet. Then use the Cyan Regist setting to select the number that 
corresponds to the cyan and black line segments most closely 
aligned. See Checking Color Registration on page 268 for more 
detailed instructions.
Magenta Regist
Adjusts the registration position of the color magenta relative to 
black.
To adjust the registration, select  Color Regist Sheet on the 
control panel’s  Information Menu  to print a color registration 
sheet. Then use the Magenta Regist setting to select the number 
that corresponds to the magenta and black line segments most 
closely aligned. See Checking Color Registration on page 268 for 
more detailed instructions.
Yellow Regist
Adjusts the registration position of the color yellow relative to 
black.
To adjust the registration, select  Color Regist Sheet on the 
control panel’s  Information Menu  to print a color registration 
sheet. Then use the Yellow Regist setting to select the number that 
corresponds to the yellow and black line segments most closely 
aligned. See Checking Color Registration on page 268 for more 
detailed instructions.
Reset Menu
This menu allows you to cancel printing and reset the printer 
settings.