Epson AcuLaser C4200DNPC5 User Manual

Installing Options301
8
8
8
8
8
8
8
8
8
8
8
8
12. Turn on the printer.
To confirm that the option is installed correctly, print a Status 
Sheet. See Printing a Status Sheet on page 377.
Note for Windows users:
If EPSON Status Monitor is not installed, you have to make settings 
manually in the printer driver. See Making Optional Settings on page 
95.
Note for Macintosh users:
When you have attached or removed printer options, you need to delete 
the printer using Print Setup Utility  (for Mac OS X...

302Installing Options
Installing an interface card
New :quote
 t
he
 information
 from
 the s
imilar
 productFollow the steps below to install an optional interface card.
c
Caution:
Before you install the interface  card, be sure to discharge any 
static electricity by touching  a grounded piece of metal. 
Otherwise, you may damage static-sensitive components.
1. Turn the printer off and unplug the power cord and all the  interface cables.
*OFF
*
 

Installing Options303
8
8
8
8
8
8
8
8
8
8
8
8
2. Remove the two screws and the Type B interface card slot cover as shown below.
w
Warning:
Do not remove screws and covers  that are not described in 
the instructions.
Note:
Keep the slot cover in a safe place.  You will need to reattach it if you 
remove the interface card later.
 

304Installing Options
3. Slide and push the interface card into the slot firmly, then 
fasten the screw as shown below.
4. Reconnect all the interface cables and the power cord.
5. Plug the printer’s power cord into an electrical outlet.
6. Turn on the printer.
To confirm that the option is installed correctly, print a Status 
Sheet. See Printing a Status Sheet on page 377.
Removing an interface card
N ew :quote  t
he
 information
 from
 the s
imilar
 product
c
Caution:
Before you remove an interface...

Installing Options305
8
8
8
8
8
8
8
8
8
8
8
8
P5C Emulation Kit
The P5C Emulation kit is available as an option for this printer. 
This module allows your printer to print documents in the PCL5c 
printing language.
Installing the P5C ROM module
New :quote  the i
nformation f
rom t
he
 s
imilar
 productFollow the steps below to install the P5C ROM module.
c
Caution:
Before you install the ROM module, be sure to discharge any 
static electricity by touching a grounded piece of metal. 
Otherwise, you may...

306Installing Options*OFF
c
Caution:
Make sure to unplug the power cord from the printer to 
prevent getting an electrical shock.
2. Remove the cover on the back of the standard lower cassette.
3. Loosen the three screws on the back of the printer.
 

Installing Options307
8
8
8
8
8
8
8
8
8
8
8
8
4. Pull out the circuit board tray.
5. Identify the ROM slot A. Its position is shown below.a. ROM slot A
b. ROM slot P
a
b
 

308Installing Options
6. Hold the ROM module above the slot and insert it into the slot 
A in the orientation shown below, until the clip comes up to 
hold the ROM module securely in place.
c
Caution:
❏Do not apply too much force.
❏ Be sure to insert the RO M module in the correct 
direction.
❏ Never remove the ROM module installed on the 
standard ROM slot P.
 

Installing Options309
8
8
8
8
8
8
8
8
8
8
8
8
7. Slide the circuit board tray into the printer.
8. Fasten the circuit board tray with the three screws.
9. Reattach the cover.
10. Reconnect all the interface cables and the power cord.
11. Plug the printer’s power cord into an electrical outlet.
 

310Installing Options
12. Turn on the printer.
To confirm that the option is installed correctly, print a Status 
Sheet. See Printing a Status Sheet on page 377.
If P5C is not listed as an installed emulation on the status sheet, 
try reinstalling the module. Make sure that it is securely seated 
into the ROM slot on the circuit board.
Removing the P5C ROM module
c
Caution:
Before you remove the ROM module, be sure to discharge any 
static electricity by touching
 a grounded piece of metal. 
Otherwise,...