Epson AcuLaser C4200DNPC5 User Manual
Have a look at the manual Epson AcuLaser C4200DNPC5 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1734 Epson manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Installing Options301 8 8 8 8 8 8 8 8 8 8 8 8 12. Turn on the printer. To confirm that the option is installed correctly, print a Status Sheet. See Printing a Status Sheet on page 377. Note for Windows users: If EPSON Status Monitor is not installed, you have to make settings manually in the printer driver. See Making Optional Settings on page 95. Note for Macintosh users: When you have attached or removed printer options, you need to delete the printer using Print Setup Utility (for Mac OS X 10.3), Print Center (for Mac OS X 10.2 or below), or Chooser (for Mac OS 9), and then re-register the printer. Removing the Hard Disk Drive N ew :quote the i nformation f rom t he s imilar product c Caution: Before you remove the Hard Disk Drive, be sure to discharge any static electricity by touching a grounded piece of metal. Otherwise, you may damage static-sensitive components. w Warning: Be careful when working inside the printer as some components are sharp and may cause injury. Perform the installation procedure in reverse. Interface Card N ew :o nly n etwork s tandard model.Your printer comes with a Type B interface slot. Various optional interface cards are available to expand your printer’s interface options.
302Installing Options Installing an interface card New :quote t he information from the s imilar productFollow the steps below to install an optional interface card. c Caution: Before you install the interface card, be sure to discharge any static electricity by touching a grounded piece of metal. Otherwise, you may damage static-sensitive components. 1. Turn the printer off and unplug the power cord and all the interface cables. *OFF *
Installing Options303 8 8 8 8 8 8 8 8 8 8 8 8 2. Remove the two screws and the Type B interface card slot cover as shown below. w Warning: Do not remove screws and covers that are not described in the instructions. Note: Keep the slot cover in a safe place. You will need to reattach it if you remove the interface card later.
304Installing Options 3. Slide and push the interface card into the slot firmly, then fasten the screw as shown below. 4. Reconnect all the interface cables and the power cord. 5. Plug the printer’s power cord into an electrical outlet. 6. Turn on the printer. To confirm that the option is installed correctly, print a Status Sheet. See Printing a Status Sheet on page 377. Removing an interface card N ew :quote t he information from the s imilar product c Caution: Before you remove an interface card, be sure to discharge any static electricity by touching a grounded piece of metal. Otherwise, you may damage static-sensitive components. Perform the installation procedure in reverse.
Installing Options305 8 8 8 8 8 8 8 8 8 8 8 8 P5C Emulation Kit The P5C Emulation kit is available as an option for this printer. This module allows your printer to print documents in the PCL5c printing language. Installing the P5C ROM module New :quote the i nformation f rom t he s imilar productFollow the steps below to install the P5C ROM module. c Caution: Before you install the ROM module, be sure to discharge any static electricity by touching a grounded piece of metal. Otherwise, you may damage static-sensitive components. w Warning: Be careful when working inside the printer as some components are sharp and may cause injury. 1. Turn the printer off and unplug the power cord and interface cable. *
306Installing Options*OFF c Caution: Make sure to unplug the power cord from the printer to prevent getting an electrical shock. 2. Remove the cover on the back of the standard lower cassette. 3. Loosen the three screws on the back of the printer.
Installing Options307 8 8 8 8 8 8 8 8 8 8 8 8 4. Pull out the circuit board tray. 5. Identify the ROM slot A. Its position is shown below.a. ROM slot A b. ROM slot P a b
308Installing Options 6. Hold the ROM module above the slot and insert it into the slot A in the orientation shown below, until the clip comes up to hold the ROM module securely in place. c Caution: ❏Do not apply too much force. ❏ Be sure to insert the RO M module in the correct direction. ❏ Never remove the ROM module installed on the standard ROM slot P.
Installing Options309 8 8 8 8 8 8 8 8 8 8 8 8 7. Slide the circuit board tray into the printer. 8. Fasten the circuit board tray with the three screws. 9. Reattach the cover. 10. Reconnect all the interface cables and the power cord. 11. Plug the printer’s power cord into an electrical outlet.
310Installing Options 12. Turn on the printer. To confirm that the option is installed correctly, print a Status Sheet. See Printing a Status Sheet on page 377. If P5C is not listed as an installed emulation on the status sheet, try reinstalling the module. Make sure that it is securely seated into the ROM slot on the circuit board. Removing the P5C ROM module c Caution: Before you remove the ROM module, be sure to discharge any static electricity by touching a grounded piece of metal. Otherwise, you may damage static-sensitive components. w Warning: Be careful when working inside the printer as some components are sharp and may cause injury. Perform the installation procedure in revers.