Epson AcuLaser C4200DNPC5 User Manual

							
Using the Control Panel251
7
7
7
7
7
7
7
7
7
7
7
7
To clear this error, select Clear Warning from the control panel’s 
Reset Menu . For instruction about accessing the control panel 
menus, see How to access the control panel menus on page 214.
Duplex Mem Overflow
There is not enough memory for duplex printing. The printer 
prints only on the front and ejects the paper. To clear this error, 
follow the instructions below.
If  Off  is selected as the  Auto Cont setting on the control panel’s 
Setup Menu , press the NStart/Stop  button to print on the back of 
the next sheet, or press the  +Cancel Job  button to cancel the 
print job.
If  On  is selected as the  Auto Cont setting on the control panel’s 
Setup Menu , printing continues automatically after a certain 
period of time.
Face-down Full
The output paper at the face-down tray is full. Remove the paper 
that has been output, then press the  NStart/Stop  button. Printing 
resumes.
Form Data Canceled
Unable to store form overlay data on the printer’s optional Hard 
Disk Drive. Either the drive is full, or the maximum number of 
form overlay files has been reached. Delete any form overlay files 
you no longer need, then try storing the new overlay again.
To clear this error, select  Clear Warning from the control panel’s 
Reset Menu . For instruction about accessing the control panel 
menus, see How to access the control panel menus on page 214.
Form Feed
 
						

							
252Using the Control Panel
The printer is ejecting paper due to a user request. This message 
appears when pressing the 
NStart/Stop  button once to make the 
printer offline, then holding down the  NStart/Stop  button for 
more than 2 seconds in order not to receive form feed command.
Format Error ROM A
An unformatted ROM module has been inserted. 
To clear this error, either press the  NStart/Stop  button or turn off 
the printer and remove the ROM module, then reinstall the ROM 
module. If that fails to clear the error, contact your dealer.
Formatting HDD
The Hard Disk Drive is being formatted. 
Hard Disk full
The optional Hard Disk Drive is full and you cannot save any 
data. Delete the unnecessary data from the Hard Disk Drive. To 
clear this error, select  Clear Warning from the control panel’s 
Reset Menu . For instruction about accessing the control panel 
menus, see How to access the control panel menus on page 214.
HDD CHECK
The printer is checking the Hard Disk Drive.
Image Optimum
There is insufficient memory to print the page at the specified 
print quality. The printer automatically lowers the print quality 
so that it can continue printing. If the quality of the printout is not 
acceptable, try simplifying the page by limiting the number of 
graphics or reducing the number and size of fonts.
 
						

							
Using the Control Panel253
7
7
7
7
7
7
7
7
7
7
7
7
To clear this error, select Clear Warning from the control panel’s 
Reset Menu. See How to access the control panel menus on page 
214 for instructions.
Turn the  Image Optimum  setting off on the control panel’s 
Printing Menu  if you do not want the printer to automatically 
lower the print quality to continue printing.
You may need to increase the amount of printer memory to be 
able to print at the desired print quality for your document. For 
more information on adding memory, see Memory Module on 
page 289.
Install Fuser
There is no fuser unit installed or the fuser unit is not installed 
properly. Turn off the printer, then install the fuser unit if it is not 
installed. 
If a fuser unit is already installed, turn the printer off and reinstall 
the unit after it has cooled off (30 minutes). Then open cover B. 
Remove the fuser unit, then reinstall it properly. Close cover B. 
The error clears automatically if the fuser unit is properly 
installed. 
If the error is not cleared, the fuser unit is out of order. Replace it 
with a new fuser unit.
Install LC1
The paper tray of the standard paper cassette is not installed, or 
not installed properly. Install the paper cassette correctly to clear 
this error.
Install LC2
The paper tray of the optional 550-sheet paper cassette unit is not 
installed, or not installed properly. Install the paper trays 
correctly to clear this error.
 
						

							
254Using the Control Panel
Install LC3
The paper trays of the optional 1100-sheet paper cassette unit are 
not installed, or not installed properly. Install the paper trays 
correctly to clear this error.
Install Photoconductr
There is no photoconductor unit installed or the photoconductor 
unit is not installed properly. Turn off the printer and install the 
photoconductor unit if it is not installed.
If a photoconductor unit is already installed, confirm cover D is 
closed. Otherwise, turn off the printer, open cover A, and then 
open cover D. Remove the photoconductor unit, then reinstall it 
properly. Close covers D and A. The error clears automatically if 
the photoconductor unit is properly installed. 
Install Transfer Unit
There is no transfer unit installed or the transfer unit is not 
installed properly. Turn off the printer, then install the transfer 
unit if it is not installed. 
If a transfer unit is already installed, turn off the printer, open 
cover A, then remove the transfer unit. Reinstall the unit properly, 
then close cover A. The error clears automatically if the transfer 
unit is properly installed. 
Install uuuu TnrCart
The indicated toner cartridges are not installed in the printer. (The 
l e t t e r s  C ,  M ,  Y ,  o r  K  a p p e a r  i n  p l a c e  o f  
uuuu and indicate the colors 
Cyan, Magenta, Yellow, and Black respectively.)
Install the indicated cartridges. See Toner Cartridge on page 312.
Invalid AUX I/F Card
 
						

							
Using the Control Panel255
7
7
7
7
7
7
7
7
7
7
7
7
This message means that the printer cannot communicate with 
the installed optional interface card. Turn off the printer, remove 
the card, then reinstall it.
Invalid HDD
Either the optional Hard Disk Drive is damaged or it cannot be 
used with this printer. Turn off the printer, then remove the Hard 
Disk Drive.
Invalid N/W Module
There is no network program, or the network program cannot be 
used with your printer. Contact a qualified service representative.
Invalid P5C
A n  o p t i o n a l  P 5 C  E m u l a t i o n  K i t  t h a t  c a n n o t  b e  u s e d  o n  t h i s  p r i n t e r  
is installed. Turn off the printer, then remove the module. 
Invalid PS3
The PostScript3 ROM module is broken. Turn off the printer and 
contact your dealer.
Invalid ROM A
The printer cannot read the installed optional ROM module. Turn 
off the printer, then remove the ROM module.
Paper Jam WWWW
The location where the paper jam occurred is displayed at WWWWW. 
WWWWW  indicates the location of the error.
If a paper jam occurs at two or more locations simultaneously, the 
corresponding multiple locations are displayed.
 
						

							
256Using the Control Panel
LC3 Error 001
Two 550-sheet paper cassette units are installed. Turn off the 
printer and remove one of them from the printer.
Manual Feed ssss
The manual feed mode is specified for the current print job. Make 
sure the paper size indicated by 
ssss is loaded, then press the 
N Start/Stop  button.
Mem Overflow
The printer has insufficient memory to execute the current task. 
Press the  NStart/Stop  button on the control panel to resume 
printing, or press the  +Cancel Job  button to cancel the print job.
Menus Locked
Location Description
Paper 
Jam AB Paper is jammed at the fuser unit. For instructions on how 
to remove jammed paper at the fuser unit, see Paper 
Jam A B on page 356.
Paper 
Jam A Paper is jammed at cover A. For instructions on how to 
remove jammed paper at cover A, see Paper Jam A on 
page 362.
Paper 
Jam CA Paper is jammed cover A and the paper cassette. For 
instructions on how to remove jammed paper at the 
Duplex Unit, see Paper Jam C A on page 367.
Paper 
Jam B Paper is jammed at cover B. For instructions on how to 
remove jammed paper at the MP tray, see Paper Jam B 
on page 375.
Paper 
Jam CAB Paper is jammed at cover A, B, the paper cassette. For 
instructions on clearing this type of paper jam, see Paper 
Jam C A B on page 376.
 
						

							
Using the Control Panel257
7
7
7
7
7
7
7
7
7
7
7
7
This message appears if you try to change the printer’s settings 
through the control panel when the buttons are locked. You can 
unlock them by using the Network utility. Refer to the Network 
Guide  for information.
Need Memory
The printer has insufficient memory to complete the current print 
job. 
To clear this error message, select  Clear Warning from the control 
panel’s  Reset Menu . SeeHow to access the control panel menus 
on page 214 for instructions.
To prevent this problem from happening again, add more 
memory to your printer as described in Memory modules on 
page 422, or reduce the resolution of the image to be printed.
NonGenuine Toner
The installed toner cartridge is not a genuine Epson product. 
Installing a genuine toner cartridge is recommended. The 
printout and remaining amount of each toner cartridge displayed 
on the control panel may be different from those when using 
genuine EPSON toner cartridges. Epson shall not be liable for any 
damages or problems arising from the use of consumable 
products not manufactured or approved by Epson.
Install a genuine Epson product, or  Clear All Warnings of the 
Reset Menu  on the control panel to clear the warning message. 
See Toner Cartridge on page 312 for instructions on replacing 
the imaging cartridge.
NonGenuine Toner uuuu
 
						

							
258Using the Control Panel
The installed toner cartridge is not an genuine Epson toner 
cartridge. The printout and remaining amount of each toner 
cartridge displayed on the control panel may be different from 
those when using genuine EPSON toner cartridges. Epson shall 
not be liable for any damages or problems arising from the use of 
consumable products not manufactured or approved by Epson. 
Installing a genuine toner cartridge is recommended. Press the 
N
Start/Stop  button on the control panel to resume printing.
Offline
The printer is not ready to print. Press the  NStart/Stop  button.
In this mode, the remaining amount of the toner cartridge for each 
color is displayed in seven levels.
Optional RAM Error
The optional memory module may be corrupted or incorrect. 
Replace it with a new one.
Paper Out tttt sssss
There is no paper in the specified paper source ( tttt). Load paper 
of the size ( sssss) into the paper source.
Paper Set tttt sssss
The paper loaded in the specified paper source ( tttt) does not 
match the required paper size ( sssss). Replace the loaded paper 
with the correct size paper and press the  NStart/Stop  button to 
resume printing, or press the  +Cancel Job  button to cancel the 
print job.
If you press the  NStart/Stop  button without replacing the paper, 
the printer will print on the loaded paper even though it does not 
match the required size.
Printer Open
 
						

							
Using the Control Panel259
7
7
7
7
7
7
7
7
7
7
7
7
Cover A, cover B, cover D, or some combination of these covers 
are open. To clear this error, close all covers.
Print Overrun
The required time to process the print data exceeded the print 
engine speed because the current page is too complex. Press the 
NStart/Stop  button to resume printing, or press the  +Cancel 
Job  button to cancel the print job. If this message appears again, 
select  On as the  Page Protect  setting in the control panel’s  Setup 
Menu  or select  Avoid Page Error  on the printer driver.
If you continue to receive this message when printing a particular 
page, try simplifying the page by limiting the number of graphics 
or reducing the number and size of fonts.
To avoid this error, it is recommended that you set the  Page 
Protect  setting to  On and add more memory to the printer. See 
Setup Menu on page 224 and Memory Module on page 289 for 
details.
PS3 Hard Disk full
The memory allocated for writing PostScript 3 commands on the 
optional Hard Disk Drive is full.
To clear this error, select  Clear Warning from the control panel’s 
Reset Menu , or remove the downloaded PS fonts to make room 
on the Hard Disk Drive. For instruction about accessing the 
control panel menus, see How to access the control panel menus 
on page 214.
RAM check
The printer is checking the RAM.
Ready
 
						

							
260Using the Control Panel
The printer is ready to receive data and print.
In this mode, the remaining amount of the toner cartridge for each 
color is displayed in seven levels.
Replace Photoconductor
The photoconductor has reached the end of its service life. Turn 
off the printer, then replace the photoconductor unit with a new 
one. See Photoconductor Unit on page 318 for instructions.
The error clears automatically after you replace the unit, then 
close all printer covers. The photoconductor service life counter 
is reset automatically.
When the error light is blinking, you can continue printing by 
pressing the 
NStart/Stop  button. However, the print quality is 
not guaranteed from then on.
Replace Toner uuuu
The indicated toner cartridges are out of toner and need to be 
replaced. (The letters C, M, Y, or K appear in place of  uuuu and 
indicate the colors Cyan, Magenta, Yellow, and Black 
respectively.)
See Toner Cartridge on page 312 for instructions.
Replace Transfer Unit
The transfer unit has reached the end of its service life. Turn off 
the printer, then replace the transfer unit with a new one. See 
Transfer Unit on page 330 for instructions.
The error clears automatically after you replace the unit and close 
all printer covers. The transfer unit service life counter is reset 
automatically.
Reserve JobCanceled