Home > Epson > Printer > Epson AcuLaser C4200DNPC5 User Manual

Epson AcuLaser C4200DNPC5 User Manual

Here you can view all the pages of manual Epson AcuLaser C4200DNPC5 User Manual. The Epson manuals for Printer are available online for free. You can easily download all the documents as PDF.

Page 291

Installing Options291
8
8
8
8
8
8
8
8
8
8
8
8
3. Loosen the three screws on the back of the printer.
4. Pull out the circuit board tray.
 

Page 292

292Installing Options
5. Identify the memory slot. Its position is shown below.
* Memory slot
6. Hold the memory module and insert it into the slot in the  orientation shown below until it stops. Then press both sides 
of the memory module down. Confirm that the notch on the 
memory module matches that of the memory slot.
*notch
*
*
 

Page 293

Installing Options293
8
8
8
8
8
8
8
8
8
8
8
8
c
Caution:
❏Do not apply too much force.
❏ Be sure to insert the memo ry facing the correct way.
❏ Do not remove any modules from the circuit board. 
Otherwise, the printer will not work.
7. Slide the circuit board tray into the printer.
 

Page 294

294Installing Options
8. Fasten the circuit board tray with the three screws.
9. Reattach the cover.
10. Reconnect all the interface cables and the power cord.
11. Plug the printer’s power cord into an electrical outlet.
12. Turn on the printer.
To confirm that the option is installed correctly, print a Status 
Sheet. See Printing a Status Sheet on page 377.
Note for Windows users:
If EPSON Status Monitor is not installed, you have to make settings 
manually in the printer driver. See Making Optional...

Page 295

Installing Options295
8
8
8
8
8
8
8
8
8
8
8
8
Removing a memory module
c
Caution:
Before you remove a memory module, be sure to discharge any 
static electricity by touching a grounded piece of metal. 
Otherwise, you may damage static-sensitive components.
w
Warning:
Be careful when working inside the printer as some components 
are sharp and may cause injury.
Note:
If the optional Hard Disk Drive is in stalled, remove it before uninstalling 
a memory module.
Perform the installation procedure in...

Page 296

296Installing Options
w
Warning:
Be careful when working inside the printer as some components 
are sharp and may cause injury.
1. Turn the printer off and unplug the power cord and all the  interface cables.
*OFF
c
Caution:
Make sure to unplug the power cord from the printer to 
prevent getting an electrical shock.
*
 

Page 297

Installing Options297
8
8
8
8
8
8
8
8
8
8
8
8
2. Remove the cover on the back of the standard lower cassette.
3. Loosen the three screws on the back of the printer.
 

Page 298

298Installing Options
4. Pull out the circuit board tray.
5. Align the three screw holes on the Hard Disk Drive with the 
screw holes on the circuit board. Secure it by tightening the 
three screws provided.
 

Page 299

Installing Options299
8
8
8
8
8
8
8
8
8
8
8
8
Note:
Be careful not to damage the cable when tightening the screws.
c
Caution:
Do not remove any modules from the circuit board. 
Otherwise, the printer will not work.
6. Connect the Hard Disk Drive cable to the circuit board.
 

Page 300

300Installing Options
7. Slide the circuit board tray into the printer.
8. Fasten the circuit board tray with the three screws.
9. Reattach the cover.
10. Reconnect all the interface cables and the power cord.
11. Plug the printer’s power cord into an electrical outlet.
 
Start reading Epson AcuLaser C4200DNPC5 User Manual

Related Manuals for Epson AcuLaser C4200DNPC5 User Manual

All Epson manuals