Epson AcuLaser C2800DN User Manual

AcuLaser C2800 Series Users Guide
Installing Options201
Removing a memory module
c
Caution:
Before you remove a memory module, be sure to discharge any static electricity by touching a grounded 
piece of metal. Otherwise, you may damage static-sensitive components.
w
Warning:
Be careful when working inside the printer as some components are sharp and may cause injury.
Perform the installation procedure in reverse.
 

AcuLaser C2800 Series Users Guide
Replacing Consumable Products202
Chapter 10 
Replacing Consumable Products
Replacement Messages
If a consumable product reaches the end of its service life, the printer stops printing and displays 
the following messages on the LCD panel or the window of EPSON Status Monitor. When this 
happens, replace the depleted consumable products.
* The letters C, M, Y, or K appear in this position, indicating the color of the imaging cartridge to be replaced. For 
example, the...

AcuLaser C2800 Series Users Guide
Replacing Consumable Products203
❏Do not expose the imaging cartridge to sunlight at all and avoid exposing it to room light for 
more than five minutes. Exposure to light can damage the drum, causing dark or light areas to 
appear on the printed page and reducing the service life of the drum.
w
Warning:
❏Do not touch the toner. Keep the toner away from your eyes. If toner gets on your skin or 
clothes, wash it off with soap and water immediately.
❏Keep consumable...

AcuLaser C2800 Series Users Guide
Replacing Consumable Products204
3. Remove the used imaging cartridge from the printer.
w
Warning:
Be careful not to touch the fuser, which is marked CAUTION HIGH TEMPERATURE, or the 
surrounding areas. If the printer has been in use, the fuser and the surrounding areas may be very 
hot. If you must touch one of these areas, wait 30 minutes to allow the heat to subside before doing 
so.
c
Caution:
Do not touch the transfer belt on the transfer unit to avoid damaging it....

AcuLaser C2800 Series Users Guide
Replacing Consumable Products205
5. Remove the cartridge seal, pulling straight from the imaging cartridge. Make sure to pull the 
tape slowly to avoid tearing it.
6. Insert the new imaging cartridge all the way until it stops.
 

AcuLaser C2800 Series Users Guide
Replacing Consumable Products206
7. Remove the orange plastic cover by pinching the center of the cover and pulling it.
8. Close the front cover.
 

AcuLaser C2800 Series Users Guide
Replacing Consumable Products207
Fuser Unit
Handling precautions
Always observe the following handling precautions when replacing the consumable products.
Do not touch the surface of the consumable product. Doing so may impair print quality.
w
Warning:
❏The fuser unit can be very hot if the printer has been in use. Turn the printer off and wait for 30 
minutes until the temperature has subsided before replacing the fuser unit.
❏Keep the consumable products out of the...

AcuLaser C2800 Series Users Guide
Replacing Consumable Products208
2. Press the latch on the front cover and open the cover.
c
Caution:
❏Do not leave the front cover open for more than five minutes to avoid exposing the imaging 
cartridges to light.
❏Do not expose the imaging cartridges to sunlight at all.
3. Take the light shielding paper from the new fuser unit’s package and attach it to the printer.
 

AcuLaser C2800 Series Users Guide
Replacing Consumable Products209
4. Open the paper guide on the top front of the printer.
5. Unlock the lock levers on both sides of the fuser unit.
6. Pull the fuser unit towards you and then lift it out of the printer.
 

AcuLaser C2800 Series Users Guide
Replacing Consumable Products210
w
Warning:
Be careful not to touch the fuser, which is marked CAUTION HIGH TEMPERATURE, or the 
surrounding areas. If the printer has been in use, the fuser and the surrounding areas may be very 
hot. If you must touch one of these areas, wait 30 minutes to allow the heat to subside before doing 
so.
7. Take the new fuser unit out of its package and remove the protective materials.
8. Lower the new fuser into the printer making sure that...