Epson AcuLaser C1750N User Manual

							If you see any errors, click Trouble Shooting Guide and follow the instruction.
4. Check if the printer to be installed is listed in the Select Printer screen, and then click Next.
Note:
If the printer to be installed is not listed in the Select Printer screen, try the following steps:
❏Click Refresh to update the information.
❏Click Manually add using IP address, and then enter the details of the printer manually.
5. Configure the required items on the Enter Printer Settings screen, and then click Next.
6. Select the software to be installed, and then click Install.
The “Congratulations!” screen appears.
7. Click Finish to exit this tool.
Epson AcuLaser C1750 Series     User’s Guide
Network Basics     61
 
						

							The wireless configuration is complete.
When the EpsonNet Config operation is successful and the printer is rebooted, wireless LAN
connection is completed.
Setting up a New Wireless Network Environment for Your Computer (When You Need to
Setup Your Wireless Connectivity With Your Computer)
For DHCP Network:
1. Setting up your computer for wireless connectivity:
Note:
You can also change the wireless settings using the wireless application that may be installed in your
computer.
For Windows XP and Windows Server 2003:
a
Select Network Connections from Control Panel.
b
Right-click Wireless Network Connection and select Properties.
c
Select the Wireless Networks tab.
d
Ensure that the check box for Use Windows to configure my wireless network settings
is selected.
Note:
Make note of the wireless settings on the Advanced window (step f) and the Wireless network
properties window (step h). You may require these settings later.
e
Click the Advanced button.
f
Select Computer-to-computer (ad hoc) networks only and close the Advanced dialog
box.
g
Click the Add button to display Wireless network properties.
Epson AcuLaser C1750 Series     User’s Guide
Network Basics     62
 
						

							h
On the Association tab, enter the following information and click OK.
Network name (SSID): xxxxxxxx (xxxxxxxx indicates a wireless device’s SSID which you
use)
Network Authentication: Open
Data encryption: Disabled
i
Click the Move up button to move the newly added SSID to the top of the list.
j
Click OK to close the Wireless Network Connection Properties dialog box.
For Windows Vista:
a
Display Control Panel.
b
Select Network and Internet.
c
Select Network and Sharing Center.
d
Select Connect to a network.
Epson AcuLaser C1750 Series     User’s Guide
Network Basics     63
 
						

							e
Select xxxxxxxx (xxxxxxxx indicates a wireless device’s SSID which you use) from the
network items listed in the available network list, and click Connect.
f
Click Close in the dialog box after confirming the connection is a success.
For Windows Server 2008:
a
Display Control Panel.
b
Select Network and Internet.
c
Select Network and Sharing Center.
d
Select Connect to a network.
e
Select xxxxxxxx (xxxxxxxx indicates a wireless device’s SSID which you use) from the
network items listed in the available network list, and click Connect.
f
Click Close in the dialog box after confirming the connection is a success.
For Windows Server 2008 R2 and Windows 7:
a
Display Control Panel.
b
Select Network and Internet.
c
Select Network and Sharing Center.
d
Select Connect to a network.
e
Select xxxxxxxx (xxxxxxxx indicates a wireless device’s SSID which you use) from the
network items listed in the available network list, and click Connect.
2. Check the IP address assigned by AutoIP on the printer.
a
On the operator panel, press the 
 (Menu) button.
b Select Admin Menu, and then press the 
 button.
c Select Network Setup, and then press the 
 button.
Epson AcuLaser C1750 Series     User’s Guide
Network Basics     64
 
						

							d Select TCP/IP, and then press the  button.
e Select IPv4, and then press the 
 button.
f Select IP Address, and then press the 
 button.
(Default IP address range: 169.254.xxx.yyy)
IP Address
169.254.000.041*
3. Ensure that the IP Address on your computer is assigned by DHCP.
4. Launch your web browser.
5. Enter the IP address of the printer in the address bar, and then press the Enter key.
Epson AcuLaser C1750 Series     User’s Guide
Network Basics     65
 
						

							EpsonNet Config page appears.
6. Create wireless setting of the printer on EpsonNet Config.
7. Reboot the printer.
8. Restore the wireless settings on your computer.
Note:
If the operating system on your computer provides a wireless configuration software, use it to change
the wireless settings. See the instructions below.
For Windows XP and Windows Server 2003:
a
Select Network Connections from Control Panel.
b
Right-click Wireless Network Connection and select Properties.
c
Select Wireless Networks tab.
d
Ensure that the check box for Use Windows to configure my wireless network settings
is selected.
Epson AcuLaser C1750 Series     User’s Guide
Network Basics     66
 
						

							e
Click Advanced.
f You can either set the printer to the ad-hoc mode or the infrastructure mode.
❏For Ad hoc mode:
Select Computer-to-computer (ad hoc) networks only and close the dialog box.
❏For Infrastructure mode:
Select Access point (Infrastructure) networks only and close the dialog box.
g
Click Add to display Wireless network properties.
h
Enter the setting that you will send to the printer and click OK.
i
Click Move up to move the setting to the top of the list.
j
Click OK to close the Wireless Network Connection Properties dialog box.
For Windows Vista:
a
Display Control Panel.
b
Select Network and Internet.
c
Select Network and Sharing Center.
d
Select Connect to a network.
e
Select the network, and then click Connect.
f
Click Close in the dialog box after confirming the connection is a success.
For Windows Server 2008:
a
Display Control Panel.
b
Select Network and Internet.
c
Select Network and Sharing Center.
d
Select Connect to a network.
Epson AcuLaser C1750 Series     User’s Guide
Network Basics     67
 
						

							e
Select the network, and then click Connect.
f
Click Close in the dialog box after confirming the connection is a success.
For Windows Server 2008 R2 and Windows 7:
a
Display Control Panel.
b
Select Network and Internet.
c
Select Network and Sharing Center.
d
Select Connect to a network.
e
Select the network, and then click Connect.
For Fixed IP Networks:
1. Set up your computer for wireless connectivity:
Note:
If the operating system on your computer provides a wireless configuration software, use it to change
the wireless settings. See the instructions below.
For Windows XP and Windows Server 2003:
a
Select Network Connections from Control Panel.
b
Right-click Wireless Network Connection and select Properties.
c
Select the Wireless Networks tab.
d
Ensure that the check box for Use Windows to configure my wireless network settings
is selected.
Note:
Be sure to write down the current wireless computer settings in step f and step h so that you can restore
them later.
e
Click the Advanced button.
Epson AcuLaser C1750 Series     User’s Guide
Network Basics     68
 
						

							f
Select Computer-to-computer (ad hoc) networks only and close the Advanced dialog
box.
g
Click the Add button to display Wireless network properties.
h
On the Association tab, enter the following information and click OK.
Network name (SSID): xxxxxxxx (xxxxxxxx indicates a wireless device’s SSID which you
use)
Network Authentication: Open
Data encryption: Disabled
i
Click the Move up button to move the newly added SSID to the top of the list.
j
Click OK to close the Wireless Network Connection Properties dialog box.
For Windows Vista:
a
Display Control Panel.
Epson AcuLaser C1750 Series     User’s Guide
Network Basics     69
 
						

							b
Select Network and Internet.
c
Select Network and Sharing Center.
d
Select Connect to a network.
e
Select xxxxxxxx (xxxxxxxx indicates a wireless device’s SSID which you use) from the
network items listed in the available network list, and click Connect.
f
Click Close in the dialog box after confirming the connection is a success.
For Windows Server 2008:
a
Display Control Panel.
b
Select Network and Internet.
c
Select Network and Sharing Center.
d
Select Connect to a network.
e
Select xxxxxxxx (xxxxxxxx indicates a wireless device’s SSID which you use) from the
network items listed in the available network list, and click Connect.
f
Click Close in the dialog box after confirming the connection is a success.
For Windows Server 2008 R2 and Windows 7:
a
Display Control Panel.
b
Select Network and Internet.
c
Select Network and Sharing Center.
d
Select Connect to a network.
e
Select xxxxxxxx (xxxxxxxx indicates a wireless device’s SSID which you use) from the
network items listed in the available network list, and click Connect.
Epson AcuLaser C1750 Series     User’s Guide
Network Basics     70