Epson AcuLaser C1750N User Manual

							3. If you agree to the terms of the SOFTWARE LICENSE AGREEMENT, select Agree and then click
Next.
The Easy Install Navi launches.
4. Click Start Setup.
5. Click Connect Your Printer.
Select your type of connection screen appears.
6. Select Wireless Connection, and then click Next.
The setting method selection window appears.
Epson AcuLaser C1750 Series     User’s Guide
Network Basics     41
 
						

							7. Ensure that Wizard is selected, and then click Next.
Epson AcuLaser C1750 Series     User’s Guide
Network Basics     42
 
						

							8. Enter the SSID.
9. Select Type of wireless network.
10. Configure the security setting, and then click Next.
The IP Address Settings screen appears.
11. Select IP Mode depending on your network scheme.
When IPv4 is selected:
❏Configure the following:
a
Select Type.
Epson AcuLaser C1750 Series     User’s Guide
Network Basics     43
 
						

							b Enter the following items:
❏IP Address of your printer
❏Network Mask
❏Gateway Address
When IPv6 is selected:
❏Configure the following:
a
Select Use Manual Address.
b Enter IP address of your printer.
c Enter the gateway address of your network.
When Dual Stack is selected:
Configure the IPv4 Settings and IPv6 Settings.
Epson AcuLaser C1750 Series     User’s Guide
Network Basics     44
 
						

							12. Click Next.
13. Ensure that the wireless settings are displayed, and then click Apply.
Epson AcuLaser C1750 Series     User’s Guide
Network Basics     45
 
						

							The Complete configuration screen appears.
14. Wait a few minutes until the printer restarts to establish the wireless network.
15. Click Print Printer Setting.
16. Confirm that “Wireless Status” is shown as “Good”, “Acceptable” or “Low” on the report.
Note:
When “Wireless Status” is “No Reception”, check if the wireless settings are correctly configured. To
reconfigure the wireless settings, click Next on the Complete configuration screen and then click
Return.
17. Follow the instructions until the Check Setup screen appears.
18. Confirm there are no errors displayed on the LCD panel, and then click Start Installation.
If you see any errors, click Trouble Shooting Guide and follow the instruction.
19. Check if the printer to be installed is listed in the Select Printer screen, and then click Next.
Epson AcuLaser C1750 Series     User’s Guide
Network Basics     46
 
						

							Note:
If the printer to be installed is not listed in the Select Printer screen, try the following steps:
❏Click Refresh to update the information.
❏Click Manually add using IP address, and then enter the details of the printer manually.
20. Select the required items on the Enter Printer Settings screen, and then click Next.
21. Select the software to be installed, and then click Install.
The “Congratulations!” screen appears.
22. Click Finish to exit this tool.
The wireless configuration is complete.
Using Advanced Setup to Configure Wireless Settings
To use the Advanced setup, display the Configure Wireless Settings screen.
The following procedure uses Windows XP as an example.
Displaying Configure Wireless Settings Screen
1. Insert the Software Disc provided with the printer in your computer.
2. Click Easy Install.
The SOFTWARE LICENSE AGREEMENT appears.
3. If you agree to the terms of the SOFTWARE LICENSE AGREEMENT, select Agree and then click
Next.
Epson AcuLaser C1750 Series     User’s Guide
Network Basics     47
 
						

							The Easy Install Navi launches.
4. Click Start Setup.
5. Click Connect Your Printer.
6. Select Wireless Connection, and then click Next.
The setting method selection window appears.
Epson AcuLaser C1750 Series     User’s Guide
Network Basics     48
 
						

							7. Select Advanced.
Select a connection method from the following
❏“Ethernet Cable” on page 49
❏“WPS-PIN” on page 56
❏“WPS-PBC” on page 57
❏“Operator Panel” on page 59
❏“EpsonNet Config” on page 60
Ethernet Cable
1. Select Ethernet Cable, and then click Next.
2. Follow the instructions, and then click Next.
Epson AcuLaser C1750 Series     User’s Guide
Network Basics     49
 
						

							The Printer Setup Utility screen appears.
3. Select the printer to be configured in the Select Printer screen, and then click Next.
Note:
If the printer to be configured is not listed in the Select Printer screen, try the following steps:
❏Click Refresh to update the information.
❏Click Enter IP Address, and then enter the IP address of your printer.
4. Enter the SSID.
5. Select Type of wireless network.
6. Configure the security setting, and then click Next.
The IP Address Settings screen appears.
7. Select IP Mode depending on your network scheme.
Epson AcuLaser C1750 Series     User’s Guide
Network Basics     50