Epson AcuLaser 2600N User Manual
Have a look at the manual Epson AcuLaser 2600N User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1734 Epson manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Paper Handling51 3 3 3 3 3 3 3 3 3 3 3 3 3. Load a stack of paper into the paper cassette. Make sure to load it with the printable surface up. Note: ❏Load paper after aligning the edges of the paper carefully. ❏Do not load paper that exceeds the maximum stack height. ❏To change the paper size loaded in the paper cassette, see Changing the paper size on page 52 for instructions.
52Paper Handling 4. Reinsert the paper cassette. Note: After loading paper, set the LC Size setting to match the loaded paper size on the control panel. Changing the paper size Follow the steps below to change the paper size loaded in the paper cassette. 1. Pull out the paper cassette. If paper is loaded in the paper cassette, remove it.
Paper Handling53 3 3 3 3 3 3 3 3 3 3 3 3 2. Push the tray in the paper cassette down. 3. Remove the three screws securing the tray in the paper cassette.
54Paper Handling 4. Slide the three paper guides to fit the paper size that you want to use. 5. Secure the three paper guides with the three screws.
Paper Handling55 3 3 3 3 3 3 3 3 3 3 3 3 6. Load the paper and reinsert the paper cassette. Note: After loading paper, set the LC Size setting to match the loaded paper size on the control panel. Output tray The output tray is located on the top of the printer. Since printouts are output face-down, this tray is also referred to as the face-down tray. This tray can hold up to 250 sheets.
56Paper Handling If the printouts do not stack well, open the extension on the output tray. Printing on Special Media You can print on special media which include Epson paper such as the following. Note: Since the quality of any particular brand or type of media may be changed by the manufacturer at any time, Epson cannot guarantee the quality of any type of media. Always test samples of media stock before purchasing large quantities or printing large jobs. EPSON Color Laser Paper When loading EPSON Color Laser Paper, you should make paper settings as shown below: ❏Make settings on the Basic Settings in the printer driver.
Paper Handling57 3 3 3 3 3 3 3 3 3 3 3 3 ❏You can also make these settings on the Tray Menu in the control panel. See Tray Menu on page 229. EPSON Color Laser Transparencies Epson recommends the use of EPSON Color Laser Transparencies. Note: Duplex printing is not available for transparencies. Transparencies can be loaded into the MP tray only. When using transparencies, you should make paper settings as shown below: ❏Make settings on the Basic Settings in the printer driver. ❏You can also make these settings on the Tray Menu in the control panel. See Tray Menu on page 229. Please note the following when handling this media: Paper Size:A4 Paper Source:MP Tray (up to 150 sheets or up to 16.5 mm thick stack), Lower Cassette (up to 500 sheets or up to 55 mm thick stack) Paper Type:Plain Paper Size:A4 or LT Paper Source:MP Tray (up to 60 sheets) Paper Type:Transparency
58Paper Handling ❏Hold each sheet by its edges, as oil from your fingers may transfer to the surface and damage the printable surface of the sheet. The Epson logo appears on the printable side. ❏When loading transparencies in the MP tray, insert the short edge first as shown below. ❏When using transparencies, load them in the MP tray and set the Paper Type setting to Transparency in the printer driver. ❏When the Paper Type setting in the printer driver is set to Transparency, do not load any other type of paper except transparencies. ❏When printing transparencies, the printing speed is extremely slow. c Caution: Sheets that have just been printed on may be hot. Envelopes The print quality of envelopes may be irregular because different parts of an envelope have different thicknesses. Print one or two envelopes to check the print quality.
Paper Handling59 3 3 3 3 3 3 3 3 3 3 3 3 c Caution: Do not use window envelopes. The plastic on most window envelopes will melt when it comes into contact with the fuser. Note: ❏Depending on the quality of envelopes, the printing environment, or the printing procedure, envelopes might be wrinkled. Make a trial print run before you print on a lot of envelopes. ❏Duplex printing is not available for envelopes. When loading envelopes, you should make paper settings as shown below: ❏Make settings on the Basic Settings in the printer driver. ❏You can also make these settings on the Tray Menu in the control panel. See Tray Menu on page 229. Please note the following when handling this media.Paper Size:IB5, C6, MON, C10, DL, or C5 Paper Source:MP Tray (up to 15 sheets, or a stack up to 16.5 mm thick) Paper Type:Normal
60Paper Handling ❏When printing on envelopes, be sure to set the lever on the fuser unit to the envelope position before loading the envelopes. After printing envelopes, be sure to reset the lever to the original position. Printing on media other than envelopes when the lever is set to the envelope position may cause poor print quality because the printer fails to fix toner to the media. It also may cause paper jam and dirty printouts because of the toner that adheres to the rollers inside the printer. When this happens, reset the lever to the original position and print blank pages until the printouts are clean. c Caution: Be careful not to touch the fuser, which is marked CAUTION HIGH TEMPERATURE, or the surrounding areas. If the printer has been in use, the fuser and the surrounding areas may be very hot. If you must touch one of these areas, open cover A and B, then wait 30 minutes to allow the heat to subside before doing so.