Epson AcuLaser 2600N User Manual
Have a look at the manual Epson AcuLaser 2600N User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1734 Epson manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Installing Options301 8 8 8 8 8 8 8 8 8 8 8 8 5. Secure the Hard Disk Drive with the four screws provided. c Caution You should not remove any modules from the circuit board. Otherwise, the printer will not work. 6. Plug the connection cable into both the socket on the HDD and that on the board as shown below.
302Installing Options 7. Reattach the cover to the back side of the printer and secure it with the four screws. To confirm that the option is installed correctly, print a Status Sheet. See Printing a Status Sheet on page 370. Note for Windows users: If EPSON Status Monitor 3 is not installed, you have to make settings manually in the printer driver. See Making Optional Settings on page 98. Note for Macintosh users: When you have attached or removed printer options, you need to delete the printer using Print Setup Utility (for Mac OS X 10.3), Print Center (for Mac OS X 10.2 or below), or Chooser (for Mac OS 9), and then re-register the printer. Removing the Hard Disk Drive c Caution: Before you remove the Hard Disk Drive, be sure to discharge any static electricity by touching a grounded piece of metal. Otherwise, you may damage static-sensitive components.
Installing Options303 8 8 8 8 8 8 8 8 8 8 8 8 w Warning: Be careful when working inside the printer as some components are sharp and may cause injury. Turn off the printer and perform the installation procedure in reverse. Memory Module By installing a Dual In-line Memory Module (DIMM), you can increase printer memory up to 512 MB. You may want to add additional memory if you are having difficulty printing complex graphics. This printer has two memory slots, but one slot has a 64 MB DIMM already installed in it at the time of manufacture. To increase printer memory more than 320 MB, you have to remove the original 64 MB DIMM first and then install two optional DIMMs. Installing a memory module Follow the steps below to install an optional memory module. c Caution: Before you install a memory module, be sure to discharge any static electricity by touching a grounded piece of metal. Otherwise, you may damage static-sensitive components. w Warning: Be careful when working inside the printer as some components are sharp and may cause injury. 1. Turn the printer off and unplug the power cord and interface cable.
304Installing Options 2. Remove the four screws from the cover on the back side of the printer. 3. Hold the cover with both hands and pull it toward you to remove it. w Warning: Be careful when touching the circuit board inside the back side cover since some parts may be very hot.
Installing Options305 8 8 8 8 8 8 8 8 8 8 8 8 4. Identify the RAM slot. 5. Insert the memory module vertically into the slot until the clip comes out. Make sure that the left slot has a module at all times. c Caution: ❏Do not force the memory module into the slot. ❏Be sure to insert the memory module facing the correct way. ❏You should not remove any modules from the circuit board. Otherwise, the printer will not work.
306Installing Options 6. Reattach the cover to the back side of the printer and secure it with the four screws. 7. Reconnect the interface cable and power cord and turn the printer on. To confirm that the option is installed correctly, print a Status Sheet. See Printing a Status Sheet on page 370. Note for Windows users: If EPSON Status Monitor 3 is not installed, you have to make settings manually in the printer driver. See Making Optional Settings on page 98. Note for Macintosh users: When you have attached or removed printer options, you need to delete the printer using Print Setup Utility (for Mac OS X 10.3), Print Center (for Mac OS X 10.2 or below), or Chooser (for Mac OS 9), and then re-register the printer.
Installing Options307 8 8 8 8 8 8 8 8 8 8 8 8 Removing a memory module c Caution: Before you remove a memory module, be sure to discharge any static electricity by touching a grounded piece of metal. Otherwise, you may damage static-sensitive components. w Warning: Be careful when working inside the printer as some components are sharp and may cause injury. Turn off the printer and perform the installation procedure in reverse. Interface Card Your printer comes with a Type B interface slot. Various optional interface cards are available to expand your printer’s interface options. Installing an interface card Follow the steps below to install an optional interface card. c Caution: Before you install the interface card, be sure to discharge any static electricity by touching a grounded piece of metal. Otherwise, you may damage static-sensitive components. 1. Turn the printer off and unplug the power cord and interface cable.
308Installing Options 2. Remove two screws securing the interface card slot cover and remove the cover. 3. Slide and push the interface card into the slot firmly, then fasten the screw as shown below. 4. Reconnect the interface cable and power cord and turn the printer on. To confirm that the option is installed correctly, print a Status Sheet. See Printing a Status Sheet on page 370.
Installing Options309 8 8 8 8 8 8 8 8 8 8 8 8 Removing an interface card c Caution: Before you remove an interface card, be sure to discharge any static electricity by touching a grounded piece of metal. Otherwise, you may damage static-sensitive components. Turn off the printer and perform the installation procedure in reverse. P5C Emulation Kit The P5C Emulation kit is available as an option for this printer. This module allows your printer to print documents in the PCL5c printing language. Installing the P5C ROM module Follow the steps below to install the Adobe PostScript 3 ROM module. c Caution: Before you install the ROM module, be sure to discharge any static electricity by touching a grounded piece of metal. Otherwise, you may damage static-sensitive components. w Warning: Be careful when working inside the printer as some components are sharp and may cause injury. 1. Turn the printer off and unplug the power cord and interface cable.
310Installing Options 2. Remove the four screws from the cover on the back side of the printer. 3. Hold the cover with both hands and pull it toward you to remove it. w Warning: Be careful when touching the circuit board inside the back side cover since some parts may be very hot.