Epson AcuLaser 2600DTN User Manual

							Installing Options311
8
8
8
8
8
8
8
8
8
8
8
8
4. Identify the ROM module slots.
Note:
There are two ROM slots, and either slot can be used to attach the 
ROM module.
5. Insert the ROM module horizontally into the slot until the clip 
comes out.
c
Caution:
❏Do not force the ROM module into the socket.
❏Be sure to insert the ROM module in the correct 
direction.
❏Never remove the ROM module installed on the 
standard ROM socket (P). 
 
						

							312Installing Options 6. Reattach the cover to the back side of the printer and secure 
it with the four screws.
7. Reconnect the power cord and turn the printer on.
To confirm that the option is installed correctly, print a Status 
Sheet. See  Printing a Status Sheet on page 370.
If P5C is not listed as an installed emulation on the status sheet, 
try reinstalling the module. Make sure that it is securely seated 
into the ROM slot on the circuit board.
Removing the P5C ROM module
c
Caution:
Before you remove the ROM module, be sure to discharge any 
static electricity by touching a grounded piece of metal. 
Otherwise, you may damage static-sensitive components.
w
Warning:
Be careful when working inside the printer as some components 
are sharp and may cause injury.
Turn off the printer and perform the installation procedure in 
reverse.
 
						

							Replacing Consumable Products313
9
9
9
9
9
9
9
9
9
9
9
9
Chapter 9 
Replacing Consumable Products
Replacement Messages
When you see the following messages on the LCD panel or the 
window of EPSON Status Monitor 3, replace the appropriate 
consumable products. You can continue to print for a short time 
after a message appears, but Epson recommends early 
replacement to maintain print quality and extend the life of your 
printer.
Note:
To clear the warning, select Clear All Warning from the control 
panel’s Reset Menu.
If a consumable product reaches the end of its service life, the 
printer stops printing and displays the following messages on the 
LCD panel or the window of EPSON Status Monitor 3. When this 
happens, the printer cannot resume printing until you replace the 
depleted consumable products.
LCD Panel Message Description
Worn Photoconductor The photoconductor unit has reached the 
end of its service life. 
Worn Fuser The fuser unit has reached the end of its 
service life. 
Worn Transfer Unit The transfer unit is near the end of its service 
life. 
 
						

							314Replacing Consumable Products
* T h e  l e t t e r s  C ,  M ,  Y ,  o r  K  a p p e a r  i n  t h i s  p o s i t i o n ,  i n d i c a t i n g  t h e  c o l o r  o f  t h e  t o n e r  
to be replaced. For example, the message Y Toner Low means that the 
amount of toner remaining in the yellow toner cartridge is low.
Note:
Messages appear for one consumable product at a time. After replacing 
a consumable product, check the LCD panel for replacement messages 
for other consumable products.
Even if Replace Toner uuuu or Replace Photoconductor is 
displayed on the LCD panel, you can print an additional sheets 
by pressing the NStart/Stop button on the control panel. The 
message on the LCD panel changes from Replace Toner uuuu or 
Replace Photocondctor to uuuu Toner Low or Worn 
Photoconductor.
Note:
❏Print quality cannot be guaranteed when printing with a worn 
consumable product. If print quality is not what you expected, 
replace the consumable product.
❏The printer stops printing if printing with a worn consumable 
product might damage the printer. If the printer stops printing, 
replace the consumable product.
LCD Panel Message Description
Replace Toner 
uuuu*The indicated toner cartridges are empty.
Replace 
PhotoconductorPrinting has stopped to avoid damage to the 
engine.
Replace Waste T Box The waste toner collector is full.
 
						

							Replacing Consumable Products315
9
9
9
9
9
9
9
9
9
9
9
9
Toner Cartridge
Handling precautions
Always observe the following handling precautions when 
replacing the consumable products:
❏Installing a genuine toner cartridge is recommended. Using a 
non-genuine toner cartridge may affect print quality. Epson 
shall not be liable for any damages or problems arising from 
the use of consumable products not manufactured or 
approved by Epson.
❏When handling toner cartridge, always place them on a clean 
smooth surface.
❏If you have moved a toner cartridge from a cool to a warm 
environment, wait for at least one hour before installing it to 
prevent damage from condensation.
w
Warning:
❏Do not touch the toner. Keep the toner away from your eyes. 
If toner gets on your skin or clothes, wash it off with soap and 
water immediately.
❏Keep consumable products out of the reach of children.
❏Do not dispose of used consumable products in fire, as they 
may explode and cause injury. Dispose of them according to 
local regulations.
❏If toner is spilled, use a broom and dustpan or a damp cloth 
with soap and water to clean it up. Because the fine particles 
can cause a fire or explosion if they come into contact with a 
spark, do not use a vacuum cleaner.
 
						

							316Replacing Consumable Products
Replacing a toner cartridge
Follow the steps below to replace a toner cartridge.
1. Prepare a new cartridge of the color (K, C, M or Y) displayed on 
the LCD panel.
2. Open cover D.
3. Hold the toner cartridge knob and tilt it toward you.
 
						

							Replacing Consumable Products317
9
9
9
9
9
9
9
9
9
9
9
9
4. Remove the empty toner cartridge from the printer.
5. Take the protective materials off of the new cartridge, and 
gently shake the new toner cartridge a few times.
6. Take the new toner cartridge out of its package, and remove 
the plastic protective cover from the toner cartridge.
 
						

							318Replacing Consumable Products 7. Insert the new cartridge into the printer.
8. Close the toner cartridge cover.
 
						

							Replacing Consumable Products319
9
9
9
9
9
9
9
9
9
9
9
9
9. Close cover D.
  Photoconductor Unit
Handling precautions
Always observe the following handling precautions when 
replacing the consumable products:
❏The photoconductor unit weighs 1.3 kg (2.9 lb). Be sure to hold 
it firmly by the handle when carrying it.
❏When replacing the photoconductor unit, avoid exposing it 
to room light any longer than three minutes. 
❏Be careful not to scratch the surface of the drum. Also, avoid 
touching the drum, since oil from your skin may permanently 
damage its surface and affect print quality.
❏To get the best print quality, do not store the photoconductor 
unit in an area subject to direct sunlight, dust, salty air, or 
corrosive gases (such as ammonia). Avoid locations subject to 
extreme or rapid changes in temperature or humidity. 
 
						

							320Replacing Consumable Products ❏When storing the photoconductor unit, make sure to attach 
the protective cover to the photoconductor unit and put it in 
the sealed blackout package and the box in which the 
photoconductor unit was sold, and store it in a safe level place. 
❏Do not tilt the photoconductor unit.
w
Warning:
❏Do not dispose of the used consumable products in fire, as it 
may explode and cause injury. Dispose of it according to local 
regulations.
❏Keep the consumable products out of the reach of children.
Replacing the photoconductor unit
Follow the steps below to replace the photoconductor unit, the 
waste toner collector, and the filter.
1. Open cover D.