Epson AcuLaser 2600DTN User Manual

							Using the Control Panel271
7
7
7
7
7
7
7
7
7
7
7
7
The installed toner cartridge is not a genuine Epson toner 
cartridge. Using a non-genuine toner cartridge may affect print 
quality. Epson shall not be liable for any damages or problems 
arising from the use of consumable products not manufactured 
or approved by Epson. Installing a genuine toner cartridge is 
recommended. Press the NStart/Stop button on the control panel 
to resume printing.
Offline
The printer is not ready to print. Press the NStart/Stop button.
Optional RAM Error
The optional memory module may be corrupted or incorrect. 
Replace it with a new one.
Paper Jam WWWW
The location where the paper jam occurred is displayed at WWWWW. 
WWWWW indicates the location of the error.
If a paper jam occurs at two or more locations simultaneously, the 
corresponding multiple locations are displayed.
Location Description
Jam A Paper is jammed at cover A. For instructions on how to 
remove jammed paper at cover A, see  Jam A (cover 
A) on page 346.
Jam A, B Paper is jammed at cover B. For instructions on how to 
remove jammed paper at cover B, see  Jam A, B (cover 
A and B) on page 349.
Jam MP, A Paper is jammed at the MP tray. For instructions on how 
to remove jammed paper at the MP tray, see  Jam MP, 
A (MP tray and cover A) on page 356.
 
						

							272Using the Control Panel Paper Out tttt sssss
There is no paper in the specified paper source (tttt). Load paper 
of the size (sssss) into the paper source.
Paper Set tttt sssss
The paper loaded in the specified paper source (tttt) does not 
match the required paper size (sssss). Replace the loaded paper 
with the correct size paper and press the NStart/Stop button to 
resume printing, or press the +Cancel Job button to cancel the 
print job.
If you press the NStart/Stop button without replacing the paper, 
the printer will print on the loaded paper even though it does not 
match the required size.
Please Shutdown
This message appears after all the toner cartridges are removed. 
Turn off the printer.
Please Wait
The toner cartridge to be replaced is moving to the replacement 
position in the printer.
Printer Open
Cover D, B, A, or E is open. Close all the covers.
Jam A, C1 Paper is jammed at the standard lower paper cassette. 
For instructions on clearing this type of paper jam, see  
Jam A, C1 (cover A and standard lower paper cassette) 
on page 359.
Jam A, E, 
C2Paper is jammed at the optional paper cassette. For 
instructions on clearing this type of paper jam, see  Jam 
A, E, C2 (cover A, E, and optional paper cassette) on 
page 364.
 
						

							Using the Control Panel273
7
7
7
7
7
7
7
7
7
7
7
7
Print Overrun
The required time to process the print data exceeded the print 
engine speed because the current page is too complex. Press the 
NStart/Stop button to resume printing, or press the +Cancel 
Job button to cancel the print job. If this message appears again, 
select On as the Page Protect setting in the control panel’s Setup 
Menu or select Avoid Page Error on the printer driver.
If you continue to receive this message when printing a particular 
page, try simplifying the page by limiting the number of graphics 
or reducing the number and size of fonts.
To avoid this error, it is recommended that you set the Page 
Protect setting to On and add more memory to the printer. See  
Setup Menu on page 233 and  Memory Module on page 303 
for details.
PS3 Hard Disk full
The memory allocated for writing PostScript 3 commands on the 
optional Hard Disk Drive is full.
To clear this error, select Clear Warning from the control panel’s 
Reset Menu, or remove the downloaded PS fonts to make room 
on the Hard Disk Drive. For instruction about accessing the 
control panel menus, see  How to access the control panel menus 
on page 223.
RAM CHECK
The printer is checking the RAM.
Ready
The printer is ready to receive data and print.
Remove Toner
 
						

							274Using the Control Panel This message appears when the printer switches to the B/W 
mode. See  Switching the Printing Mode on page 283 to find how 
to switch the mode.
Replace Fuser
The fuser has reached the end of its service life. Turn the printer 
off, then replace the fuser unit with a new one. See  Fuser Unit 
on page 326 for instructions.
Replace Photoconductor
The photoconductor has reached the end of its service life. Turn 
off the printer, then replace the photoconductor unit with a new 
one. See  Photoconductor Unit on page 319 for instructions.
The error clears automatically after you replace the unit, then 
close all printer covers. The photoconductor service life counter 
is reset automatically.
When the error light is blinking, you can continue printing by 
pressing the NStart/Stop button. However, the print quality is 
not guaranteed from then on.
Replace Toner uuuu
The indicated toner cartridges are out of toner and need to be 
replaced. (The letters C, M, Y, or K appear in place of uuuu and 
indicate the colors Cyan, Magenta, Yellow, and Black 
respectively.)
See  Toner Cartridge on page 315 for instructions.
Replace Waste T Box
The waste toner collector is full of toner. Replace it with a new 
waste toner collector. See  Waste Toner Collector on page 331 
for instructions.
 
						

							Using the Control Panel275
7
7
7
7
7
7
7
7
7
7
7
7
Reserve JobCanceled
The printer cannot store the data of your print job using the 
Reserve Job function. The maximum number of print jobs stored 
on the printer’s Hard Disk Drive has been reached, or the drive 
has no more memory available to store a new job. To store a new 
print job, delete a previously stored job. Also, if you have any 
Confidential Jobs stored, printing those jobs will make more 
memory available. 
To clear this error, select Clear Warning from the control panel’s 
Reset Menu. For instruction about accessing the control panel 
menus, see  How to access the control panel menus on page 223.
Reset
The printer’s current interface has been reset and the buffer has 
been cleared. However, other interfaces are still active and retain 
their settings and data.
Reset All
All printer settings have been reset to the default configuration, 
or to the last settings that were saved.
Reset to Save
A control panel menu setting was changed while the printer was 
printing. Press the NStart/Stop button to clear this message. The 
setting will become effective after printing has finished.
Alternatively you can clear this message by performing Reset or 
Reset All on the control panel. However, the print data will be 
deleted.
ROM CHECK
The printer is checking the ROM.
SELF TEST
 
						

							276Using the Control Panel The printer is currently performing a self test and initialization.
Service Req Cffff/Service Req Eggg
A controller error or a print engine error has been detected. Turn 
off the printer. Wait at least 5 seconds, then turn it back on. If the 
error message still appears, write down the error number listed 
on the LCD panel (Cffff/Eggg), turn off the printer, unplug the 
power cord, then contact a qualified service representative.
Sleep
The printer is currently in the power-save mode. This mode is 
canceled when the printer receives print data. This mode is also 
canceled by selecting Reset or Reset All from the control panel’s 
Rest Menu. See  Using the Control Panel Menus on page 223 for 
instructions.
TonerCart Error uuuu
A read/write error has occurred for the indicated toner cartridges 
(The letters C, M, Y, or K appear in place of uuuu and indicate the 
colors Cyan, Magenta, Yellow, and Black respectively.). Remove 
the toner cartridges and reinsert them. If that fails to clear the 
error, replace the toner cartridges.
To install the indicated cartridges. See  Toner Cartridge on page 
315.
Turn Paper
Paper on the MP tray is not loaded correctly. Remove the paper 
and load it correctly on the MP tray.
Unable Clear Error
The printer cannot clear an error message because the error status 
still remains. Try solving the problem again.
 
						

							Using the Control Panel277
7
7
7
7
7
7
7
7
7
7
7
7
uuuu Toner Low
This message indicates that the toner cartridge for the indicated 
color is near the end of its service life. Prepare a new toner 
cartridge.
Warming Up
The printer is warming up the fuser to be ready to print.
Waste Toner Box Near Full
The waste toner collector is near full of toner.
Worn Fuser
This message indicates that the fuser unit is near the end of its 
service life. Printing after this message appears is not guaranteed. 
Turn the printer off, then reinstall the unit after it has cooled off 
(30 minutes). Then replace the fuser unit with a new one. See  
Fuser Unit on page 326 for instructions.
The error clears automatically after you replace the unit and close 
all printer covers.
Worn Photoconductor
This message indicates that the photoconductor unit is near the 
end of its service life. Printing after this message appears is not 
guaranteed. Turn the printer off, then replace the photoconductor 
unit with a new one. See  Photoconductor Unit on page 319 for 
instructions. The error clears automatically after you replace the 
unit and close the printer covers.
Worn Transfer Unit
This message warns you that the transfer unit is near the end of 
its service life. Contact your dealer.
 
						

							278Using the Control Panel To clear this warning message and continue printing, select Clear 
All Warning from the control panel’s Reset Menu. For instruction 
about accessing the control panel menus, see  How to access the 
control panel menus on page 223.
Write Error ROM P
The printer is unable to write data into the ROM module correctly. 
You cannot remove the ROM P because the ROM P is a program 
ROM module. Contact your dealer.
Writing ROM A/Writing ROM P
This message indicates that a ROM module in the slot is being 
written. Please wait until this message disappears.
Printing and Deleting Reserve Job Data
Print jobs stored on the printer’s optional Hard Disk Drive using 
the Re-Print Job, Verify Job, and Stored Job options of the Reserve 
Job function can be printed and deleted using the control panel’s 
Quick Print Job Menu. Jobs saved using the Confidential Job 
option can be printed from the Confidential Job Menu. Follow the 
instructions in this section.
Using the Quick Print Job Menu
Follow the steps below to print or delete Re-Print Job, Verify Job, 
and Stored Job data.
1. Make sure the LCD panel displays Ready or Sleep, then press 
the Enter button to access the control panel menus.
2. Press the dDown button repeatedly until Quick Print Job 
Menu appears on the LCD panel, then press the Enter button.
 
						

							Using the Control Panel279
7
7
7
7
7
7
7
7
7
7
7
7
3. Use the dDown or uUp button to scroll to the appropriate 
user name, then press the Enter button.
4. Use the dDown or uUp button to scroll to the appropriate 
job name, then press the Enter button.
5. To specify the number of copies you want to print, press the 
Enter button, then use the dDown and uUp buttons to 
select the number of copies.
To delete the print job without printing any copies, press the 
dDown button to display Delete on the LCD panel.
6. Press the Enter button to start printing or to delete the data.
Using the Confidential Job Menu
Follow the steps below to print or delete Confidential Job data.
1. Make sure the LCD panel displays Ready or Sleep, then press 
the Enter button to access the control panel menus.
2. Press the dDown button repeatedly until 
ConfidentialJobMenu appears on the LCD panel, then press 
the Enter button.
3. Use the dDown or uUp button to scroll to the appropriate 
user name, then press the Enter button.
 
						

							280Using the Control Panel 4. Enter your four-digit password by using the corresponding 
buttons, as shown below.
Note:
❏Passwords are always four digits.
❏Passwords consist of numbers from 1 through 4.
❏If no print jobs have been saved with the password you entered, 
Password Error appears briefly on the LCD panel then the 
printer exits the control panel menus. Confirm the password 
and try again.
5. Use the dDown or uUp button to scroll to the appropriate 
job name, then press the Enter button.
6. To specify the number of copies you want to print, press the 
Enter button, then use the dDown and uUp buttons to 
select the number of copies.
To delete the print job, press the dDown button to display 
Delete on the LCD panel.
7. Press the Enter button to start printing or to delete the data.