EMAK Riding Mower F72 Operators Manual

FR 40PANNES ET REMÈDES
PROBLÈME CONDITION CAUSE PROBABLE SOLUTIONS
4. Le démarrage
est difficile ou le
moteur ne fonc-
tionne pas régu-
lièrement
5. Le rendement
du moteur est
faible lors de la
tonte
6.Le moteur
s’arrête et le
voyant clignote
7.Le moteur
s’arrête et le
voyant s’éteint
8.Le moteur
s’arrête et le
voyant reste allu-
mé
9. Tonte irréguliè-
re et ramassage
inefficaceClé sur
«MARCHE»
moteur en
route 
Clé sur
«MARCHE»
moteur en
route
Clé sur
«MARCHE»
moteur en
route
Clé sur
«MARCHE»
moteur en...

FR 41 PANNES ET REMÈDES
PROBLÈME CONDITION CAUSE PROBABLE SOLUTIONS
10. Vibrations
anormales lors
de la tonteClé sur
«MARCHE»
moteur en
route–vitesse de déplacement trop éle-
vée par rapport à la hauteur
dherbe à couper
–goulotte déjection bouchée
–plateau de coupe plein dherbe
–lame déséquilibrée
–lame mal serrée
–fixations relâchées
– plateau de coupe bouché–reduire la vitesse et/ou rele-
ver le plateau de coupe
–attendre que lherbe soit
sèche
–enlever le bac et vider la
goulotte déjection
–nettoyer le...

FR 42ACCESSOIRES OPTIONNELS 
8. ACCESSOIRES OPTIONNELS
1. CONTRE-POIDS FRONTAUX
Améliorent la stabilité avant de la machine notam-
ment lorsque cette dernière est purtout utilisée sur
les pentes. 
2. PARE-PIERRES
À utiliser à la place du bac lorsque lherbe nest
pas récupérée.
3. CHARGEUR DE BATTERIES DE MAINTIEN
“CB01”
Il permet de maintenir en bon état la batterie pen-
dant les périodes d’inactivité de la machine en
assurant un niveau de charge optimal et donc une
durée de vie prolongée de la batterie....

FR 43 CARACTÉRISTIQUES TECHNIQUES
706 1130750 1546760 1863
860
1100
9. CARACTERISTIQUES TECHNIQUES
Installation électrique  ................... 12 V
Batterie ....................................... 18 Ah
Pneus avant  ........................... 11 x 4-4
Pneus arrière  ...........................15 x 6-6
Pression de gonflage avant .......1,5 bar
Pression de gonflage arrière  .. . 1,0 bar
Poids total  ...................... 159 ÷ 168 kg
Diamètre interne du braquage
(diamètre minimum de la zone
non tondue)...

INTRODUCTION
Dear Customer,
We thank you for having purchased our riding mower and hope that it will fully
meet all your expectations.
This manual has been compiled in order that you may get to know your machine
and to be able to use it safely and efficiently. Don’t forget that the manual forms
an integral part of the machine so keep it handy so that it can be consulted at
any time, and pass it on to the purchaser if you resell the machine.
Your new machine has been designed and made in line with current...

TABLE OF CONTENTS
1. SAFETY .......................................................................................................... 3
Regulations for using the machine safely
2.  IDENTIFICATION OF THE MACHINE AND PARTS...................................... 7
Explanations on how to identify the machine and its main parts
3. UNPACKING AND ASSEMBLY...................................................................... 9
Explanations on how to remove the packing and on how to assemble
separated parts
4....

1. SAFETY
HOW TO READ THE MANUAL
This manual describes both mechanically and hydrostatically driven machines,
as well as versions including equipment and accessories that may not be avail-
able in your area.
The symbol   highlights all differences in usage and is followed by the indica-
tion of the type of drive or version to which it refers.
Some paragraphs in the manual contain information of particular importance and
these are highlighted at various levels of emphasis, and signify the following:
or...

6) Do not carry passengers.
7) The operator of a machine must carefully follow the driving instructions, particularly:
–the need for care and concentration when using machines;
–that control of a machine sliding on a slope will not be regained by the application of the
brake. 
The main reasons for loss of control are:
–insufficient wheel grip;
–being driven too fast;
–inadequate braking;
–the type of machine is unsuitable for its task;
–lack of awareness of the effect of ground conditions, especially...

crossing surfaces other than grass. 
8) Never use the machine to cut grass if the guards are defective, or without the stone-
guard and/or grass-catcher in place.
9) Do not change the engine governor settings or overspeed the engine.
10) Before leaving the operator’s position:
–disengage the blade;
–change into neutral (  or mechanical drive models) or make sure that the speed
change lever has returned to the neutral position (  or hydrostatic drive models) and
engage the parking brake;
–stop the engine...

SAFETY DECALS
Your machine must be used with care. Therefore, decals have been placed on
the machine, to remind you pictorially of the main precautions to take during
use. These decals are to be considered an integral part of the machine.
If a decal should fall off or become illegible, contact your retailer to replace it.
Their meaning is explained below.
EN 6SAFETY
Warning:Read Operator’s Man-
ual before operating this
machine.
Warning:Disconnect the igni-
tion key and read the instruc-
tions before...