Elmo Boxi T-350 Mobile Projector Instruction Manual

 
 
31 
 
 
2 BASIC OPERATION 
TURNING THE POWER ON/OFF 
Powering on 
1. Make sure that the power and all necessary cables are connected 
properly. 
 
2. Press the  button on the control panel or on the remote control. 
 
 
 
 
 
 
 
 
 
 
 
 
 
Power indicator  will turn green. 
 
 
The “Input source standby” screen will be displayed. 
 
 
 
■ It will take some time before you can operate the projector after the power 
is on. 
N o t e 
Control panel Remote control          

 
 
32 
 
 
Powering off 
1. Press the  button on the control panel or on the remote control. 
 
 
 
 
 
 
 
 
 
2. A message will be displayed. Press the  button again.  
Press the Power button on the control panel of 
the projector or on the remote control while the 
message in the right figure is displayed to turn 
off the power. 
 
 
The Power indicator  will turn off. 
The Wireless LAN indicator will also turn off. 
 
The cooling fan will operate for a while. Disconnect the power cord after the fan...

 
 
33 
 
 
ADJUSTING THE FOCUS 
 
Turn the focus ring to adjust the focus. 
 
 
 
 
 
 
 
 
 
 
 
 
■ The focus adjustment can be performed when the throw distance is 
between 48cm and 133cm. 
■ Refer to “Throw distance and screen size” (Page21) for details on the 
screen size. 
■ Sometimes, you may notice fine streaks on projected images. This is 
due to interference with the screen surface. Replace the screen or 
displace the focus a little. 
 CAUTION 
■ Do not look into the lens during the...

 
 
34 
 
 
CORRECTING THE KEYSTONE DISTORTION 
Correcting the keystone distortion manually with the 
remote control 
1. Press the the  button. 
The following “Keystone correction” window will be displayed. 
 
 
 
 
 
 
 
 
 
2. Press the “ ” buttons. 
 
Press the “>” button.  
 
 
(Press when the projection 
angle is increased.) 
Press the “

 
 
35 
 
Display mode select menu 
2. Press the “ ” buttons on the control panel to correct the 
keystone distortion. 
Press the “” button.  
 
 
(Press when the projection 
angle is increased.) 
Press the “” button.  
 
 
(Press when the projection 
angle is decreased.) 
 
 
 
 
SELECTING THE DISPLAY MODE (remote control) 
 
1.   Press the  button on the remote control. 
“Display mode select” menu will be displayed. 
 
2.   Press the “ ” buttons of remote 
control. 
Select the display mode with the...

 
 
36 
 
 
CONTROLLING THE VOLUME (remote control) 
 Turning up the volume 
1. Press the “+” button near the  mark on the remote control. 
The following “Volume control” window will be displayed and the volume will be 
turned up. 
 
 
 
 
 
 
 
 
 
 
 
Turning down the volume 
1. Press the “-” button near the  mark on the remote control. 
The following “Volume control” window will be  
displayed and the volume will be turned down. 
 
 
 
 
 
 
 
 
 
 
 
 
■ The “Volume control” window will be...

 
 
37 
 
Controlling the volume with control panel 
1. Press the “”button on the control panel. 
 The following “Volume control” window  
will be displayed. 
 
 
 
 
 
 
2. Press the “ ” buttons on the control panel to controlling the 
volume. 
Press the  buttons : Turning up the volume 
Press the  buttons : Turning down the volume. 
 
 
■ The “Volume control” window will be automatically closed after 3 
seconds of no operation.  
■ The volume control can also be performed from the menu.  
Refer to...

 
 
38 
 
 
TURNING OFF THE SOUND 
You can temporarily mute the sound from the built-in speaker. 
 
1. Press the  button to mute the sound. 
Press the  button again to cancel the mute. 
 
When the “+” button near the  mark on the remote control 
is pressed while in mute, the mute will be released and the 
volume will be increased by 1 level. 
When the “-” button near the  mark on the remote control is 
pressed while in mute, the mute will be released and the 
volume will be decreased by 1 level....

 
 
39 
 
 
ADJUSTING THE BRIGHTNESS (remote control) 
Adjust the brightness on the remote control. 
1. Press the  button on the remote control. 
The “Brightness adjustment” window will be displayed. 
 
 
 
 
 
 
 
 
2. Press the “ ” buttons of remote control. 
Adjust the brightness with the   buttons. 
 
 
 
 
Remote control 
Brightness adjustment window 
 Darken Lighten  
■ The “Brightness adjustment” window will be automatically closed after 3 
seconds of no operation.  
■ The brightness adjustment...

 
 
40 
 
 
ADJUSTING THE CONTRAST (remote control) 
Adjust the contrast on the remote control. 
1. Press the  button on the remote control. 
 The “Contrast adjustment” window will be displayed. 
 
 
 
 
 
 
 
 
2. Press the “ ” buttons of remote control. 
Adjust the contrast with the “ ” buttons. 
 
 
■ The “Contrast adjustment” window will be automatically closed after 3 
seconds of no operation.  
■ The contrast adjustment cannot be done from the “Input source standby” 
screen. 
■ The contrast...