Elmo Boxi T-350 Mobile Projector Instruction Manual

 
 
21 
 
 
INSTALLING THE PROJECTOR 
Throw distance and screen size 
Decide on the position to place the projector. 
The distance between the projector and the screen should be between 48cm (screen 
size: 25 inch) and 133 cm (screen size: 68 inch). 
 
 
 
 
 
 
 
 
 
 
Screen size Projection distance 
Inch Width (cm) Height (cm) L(cm) 
25 53.8 33.7 48 
30 64.6 40.4 58 
35 75.4 48.0 68 
40 86.1 53.8 78 
45 96.9 60.6 88 
50 107.7 67.3 98 
55 118.5 74.0 108 
60 129.2 80.8 118 
65 140.0 87.5 128 
68 146.5...

 
 
22 
 
 
Raising the projected image 
 Projected image can be raised up when using the built-in tilt stand underneath the 
projector. 
 
Bottom of the projector 
 
 
  
 
 
 
 
 
 
1. Use the tilt stand 
Setting up the tilt stand allows you to raise the projected image. 
Two positions tilt stand allow you to set up projection angle to either 5°or 10°. 
The more inclination angle is added, the higher the image is projected. 
 
 
 
2. Reset the position of the projected image. 
The projector will...

 
 
23 
 
 
Using the protective cover (Sold separately) 
The followings are the instructions on how to install and use the protective cover 
(Sold separately). 
The protective cover can be used as a projection stand as well as a protection cover 
for the projector. 
 
How to install the protective cover 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
① Attach the supplied the hook and loop 
fastener to the bottom of the projector 
(marked in red dotted lines). 
The hook and 
loop fastener 
② Place the projector on the...

 
 
24 
 
 
How to use the protective cover 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Cover the projector to protect it from damage. 
■ Be sure to firmly hold the bottom of the projector and avoid applying an 
excessive vibration or impact when you carry the projector with the 
protective cover. The projector may slip out of the cover and drop to the 
ground, causing malfunction of the projector.    
■ Do not use the projector with the protective cover on it. 
Doing so can cause the protective cover to get...

 
 
25 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Use the protective cover as a projection stand. 
◎Change the projection angle by adjusting 
the position of the tape. 
 
■ When using the protection cover as a projection stand, observer the 
following precautions for safety use of the projector.    
- Do not look into the lens while the projector is being used. Strong light 
is emitted from the projectors lens. If you look directly into this light, it 
can hurt and damage your eyes....

 
 
26 
 
 
Using a tripod for a camera  
The projector is equipped with a tripod receptacle on the bottom of the projector. You 
can mount the projector on a tripod for a camera. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
■ Use a tripod that can support 500g or more. 
■ Fully spread the legs of the tripod. In case of using a tripod with an 
elevating column, do not extend the column when mounting the 
projector. 
■ Refer to the instruction manual of the tripod for instructions on the use...

 
 
27 
 
 
CONNECTING TO THE DEVICES 
Connecting the power (AC adapter and power cord) 
Connect the supplied AC adapter and the power cord, and then firmly connect to the 
DC IN 19V  of the projector.  
Then insert the other plug of the power cord securely into the wall outlet. 
 
BACK 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
■ The supplied AC adapter and power cord are for use with the projector 
only. Do not use with other devices. 
■ Do not place the projector on carpet, cushions or bedding and do not 
cover...

 
 
28 
 
 
Connecting to HDMI terminal 
1. Connect the projector to a device such as a DVD-player using HDMI 
cable. 
Connect the HDMI output terminal of your device such as a DVD-player and 
computer to the HDMI terminal of the projector using an HDMI cable (sold 
separately) as shown in the below picture. Firmly insert the cable into the 
connector. 
BACK 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
■ Use the HIGH SPEED HDMI cable with HDMI logo. 
HDMI cable that is not compliant with HDMI standard may not be...

 
 
29 
 
Output audio through the AUDIO terminal 
1. Connect headphones or an external speaker to the projector 
Plug in headphones(sold separately) or an external speaker(sold separately) to 
the AUDIO output port of the projector.  
Built-in speaker output will be stopped and audio will be output through 
headphones or an external speaker. 
BACK 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
    
            
2. Adjust audio volume of the headphone 
Audio volume of headphone can be adjusted by volume settings shown...

 
 
30 
 
 
 
■ Please  be  careful of  volume  level when  using  headphones.  Continuous 
usage of the headphone at very high volume may cause hearing loss. In 
order to protect hearing, please do not turn up the volume level too high. 
Please  increase  volume  gradually  as  sudden  increases  may  harm 
hearing. 
■ Please  do  not  add  extra  force  to  the  projector  when  inserting 
headphones as this may cause damage. 
■  
 CAUTION