Eiki Projector Lc Xb22 User Manual

11
Part Names and Functions
Part Names and Functions
Remote Control
q
w
e
r
t
y
i
!5
!6
!7o
!0
qSIGNAL EMISSION indicator
This indicator lights red while the laser beam is being emitted from the laser light
window or a signal is being sent from the remote control to the projector.
eD.ZOOM (e ed
d
) button
Select the Digital zoom +/– mode and resize the image. (p31)
!7MUTE button
Mute the sound. (p23)
rPOINT (e ed
d
7 8) buttons
Select an item or adjust the value in the On-Screen Menu. These are also used...

12
Part Names and Functions
This remote control emits a laser beam from the laser light window.  With the LASER button pressed, laser light goes on.
The signal emission indicator lights red and laser is emitted with red light.  With the LASER button pressed for more than 1
minute or released, the light goes off.  
To lock this function, press both the MENU button and the NO SHOW button for more than 10 seconds.  To unlock, press
the  MENU button and NO SHOW button again for more than 10 seconds.  
The...

13
Installation
Projection angle can be adjusted up to 11.8 degrees with the
adjustable feet. 
Lift the front of the projector and pull upward the feet lock
latches on both sides of the projector.1
Adjustable Feet
Feet Lock Latches
Release the feet lock latches to lock the adjustable feet and
rotate the adjustable feet to adjust the position and tilt. 2
To retract the adjustable feet, lift the front of the projector
and pull and undo the feet lock latches.
Keystone distortion of the projected image can...

14
NOTE ON THE POWER CORD
AC power cord must meet requirement of the country where you use a projector.
Confirm an AC plug type with the chart below and proper AC power cord must be used.
If supplied AC power cord does not match your AC outlet, contact your sales dealer.
Installation
To power cord
connector on your
projector.
Projector sideAC outlet side
Ground
To the AC outlet.
(120 V AC)
For Continental EuropeFor the U.S.A. and Canada
This projector uses nominal input voltages of 100-120 V or 200-240
V...

15
Installation
Installation
Connecting to a Computer
COMPUTER  IN  1DVI - I
MONITOR  OUT
S-VIDEO
COMPUTER IN 2 / COMPONENT IN / 
COMPUTER / COMPONENT
AUDIO  IN
AUDIO  IN
RVIDEOLUSB
SERVICE PORT 
RESET
(MONO)
ARIALE)
AUD
COMPUTER  IN  1
MONITOR  OUT
S-VIDEO
 
COMPUTER / COMPONENT
AUDIO  IN
AUDIO  IN
RVIDEOLUSB
SERVICE PORT 
RESET
(MONO)/ COMPONENT  IN  
COMPUTER  IN  2
/   
AUDIO  OUT
(VARIABLE)
Cables used for connection
• VGA Cable (Mini D-sub 15 pin) (Only one cable is supplied.)
• USB Cable✽
• Audio...

16
COMPUTER  IN  1DVI - I
MONITOR  OUT
S-VIDEO
COMPUTER IN 2 / COMPONENT IN / 
COMPUTER / COMPONENT
AUDIO  IN
AUDIO  IN
RVIDEOLUSB
SERVICE PORT 
RESET
(MONO)
(VARIABLE)
AUDIO  OUT
COMPUTER  IN  1
MONITOR  OUT
S-VIDEO
 
COMPUTER / COMPONENT
AUDIO  IN
AUDIO  IN
RVIDEOLUSB
SERVICE PORT 
RESET
(MONO)/ COMPONENT  IN  
COMPUTER  IN  2
/   
AUDIO  OUT
(VARIABLE)
Installation
Connecting to Video Equipment
Cables used for connection
• Video and Audio Cable (RCA x 3) ✽
• S-VIDEO Cable ✽
• Audio Cable (Mini Plug:...

17
Installation
Installation
Connecting to Component Video Equipment
COMPUTER  IN  1DVI - I
MONITOR  OUT
S-VIDEO
COMPUTER IN 2 / COMPONENT IN / 
COMPUTER / COMPONENT
AUDIO  IN
AUDIO  IN
RVIDEOLUSB
SERVICE PORT 
RESET
(MONO)
(VARIABLE)
AUDIO  OUT
MONITOR  OUT
S-VIDEO
 
COMPUTER / COMPONENT
AUDIO  IN
AUDIO  IN
RVIDEOLUSB
SERVICE PORT 
RESET
(MONO)COMPUTER  IN  1/ COMPONENT  IN  
COMPUTER  IN  2
/   
AUDIO  OUT
(VARIABLE)
Cables used for connection
• Audio Cable (Mini Plug (stereo) x 2 or RCA x 2) ✽
•...

18
Connect the projectors AC power cord into an AC outlet.
The POWER indicator blinks red in a moment and lights red.
Press the POWER ON-OFF button on the top control or on
the remote control.  The POWER indicator turns green
lighting and the cooling fans start to operate.  The
preparation display appears on the screen and the count
down starts. 
2
3
1
16
The preparation display disappears after 20 seconds.
4After the count-down, the input source that was selected
last and the Lamp mode status icon (see...

19
Basic Operation
Basic Operation
Press the POWER ON-OFF button on the top control or on
the remote control, and a message Power off? appears on
the screen.  
Press the POWER ON-OFF button again to turn off the
projector. The POWER indicator starts to blink red, and it
continues while the cooling fans are operating for about 90
seconds. (About 120 seconds when the fan mode is L2. See
page 44.)   
1
2
TO MAINTAIN THE LIFE OF LAMP, ONCE YOU TURN
PROJECTOR ON, WAIT AT LEAST 5 MINUTES BEFORE
TURNING IT...

20
Basic Operation
ON - OFFPOWER
KEYSTONE   INPUT
WARNING
LAMP
REPLACE
SELECT
MENUVOLUME–VOLUME+
Top Control
Menu bar Pointer
(red frame)Menu icon
Item data
Press the Point 
7 8buttons
to adjust value.
SELECT
button
Pointer (red frame)
Press the Point d button to
move the pointer.
Item
SELECT button POINT buttons
Remote Control
How to Operate the On-Screen Menu
MENU button SELECT button POINT button
(outer ring)
On-Screen Menu
Quit to exit this menu.
The projector can be adjusted or set via the On-Screen...