Eiki Projector Lc Wxl200a User Manual

31
Basic Operation
If a projected picture still has keystone distortion after pressing the \
AUTO PC button on the remote control, correct the image manually 
as follows:
Press the KEYSTONE button on the remote control to switch the 
Standard (for Vertical/Horizontal) /Corner correction adjustment. 
The Standard or Corner correction adjustment dialog box appears. 
Use the Point ▲▼◄► buttons to correct the Standard or Corner 
distortion. The Standard or Corner correction adjustment can be 
stored (see...

32
Note:   You	can	choose	the	pattern	of	Pointer	(Dot/Arrow/Finger)	in	the	Setting	Menu	(p.60)
You can move the Pointer of the projector with the remote control to emph\
asize a part of the projected image.  
Press the POINTER button to activate the Pointer function.1
2
3To cancel the Pointer function, press the POINTER button 
again or press any other button. 
Use the MOUSE POINTER button to move the Pointer. 
The remote control can be used as a wireless mouse for your computer. 
Before operating the...

33
The input source changes each time you press the INPUT button on the side control or the remote control as follows:
 Input 1→ Input 2→ Input 3 → ...
Before using the INPUT button on the side control or the remote control, you must select a cor\
rect input source by On-
Screen Menu and the latest input source will be displayed.
Input Selection
Press the INPUT 1, INPUT 2, or INPUT 3 button on the remote control. The input source appears on the screen as you 
press each button. Select the connected input...

34
INPUT MENU
When your computer is connected to the INPUT 1 (ANALOG) 
terminal, select RGB (PC analog).
RGB(PC analog)
Note:
			 Input	source	changes	if	the	INPUT	1	button	on	the	remote	control	is	pressed.
When connecting the computer output [5 BNC Type (Green, Blue, 
Red, Horiz. Sync, and Vert. Sync.)] from the computer to G, B, R, 
H/HV, and V jacks:
Input Selection
When your computer is connected to the INPUT 2 (5 BNC 
INPUT JACKS) terminal, select RGB.
RGB 
1
2
3
Press the MENU button to display...

35
When the video input signal is connected to the 
Y-Pb/Cb-Pr/Cr jacks, select y,Pb/Cb,Pr/Cr.
When the video input signal is connected to the 
VIDEO jack, select Video.
When the video input signal is connected to the 
S-VIDEO jack, select S-video.
When connecting to video equipment, select the type of Video source 
in the Source Select Menu. 
When the video input signal is connected to the 
Y-Pb/Cb-Pr/Cr jacks, select y,Pb/Cb,Pr/Cr.
When the video input signal is connected to the 
VIDEO jack, select...

36
Computer Input
PC System Menu
PC System Menu1
2
PC system can also be selected manually.
The PC System Menu  Selected system is    displayed.
Press the MENU button to display the On-Screen Menu. Use 
the Point ▲▼ buttons to select Input and then press the Point 
► or the SELECT button. 
Use the Point ▲▼ buttons to select System and then press 
the Point ► or the SELECT button.
Use the Point ▲▼ buttons to select the desired system and 
then press the SELECT button.3
Systems in this dialog box can be...

37
Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots, Position H and Position V to conform 
to your computer. 
To store the adjusted parameters .The adjusted parameters from the Auto PC Adjustment can be stored in the projector. Once the parameters are stored, the setting can be done just by selecting Mode in PC SYSTEM Menu (p.36). See “Manual PC Adjustment” on pages 38-39.
Note:
	 •	 Fine	sync,	Total	dots,	Position	H	and	Position	V		of	certain	computers	cannot	be...

38
Some computers employ special signal formats which may not be tuned by M\
ulti-Scan system of this projector. Manual PC 
Adjustment enables you to precisely adjust several parameters to match t\
hose special signal formats. The projector has 
10 independent memory areas to store those parameters manually adjusted.\
 It allows you to recall the setting for a specific 
computer. 
Use  the  Point ◄► buttons  to  adjust  the  value,  eliminating  a  flicker 
from the image displayed (from 0 to 31).
Use...

39
Computer Input
Note:
•	Display area (H/V)	cannot	be	selected	when	480i,	575i,	
480p,	575p,	720p,	1035i,	1080i or 1080p	is	selected	in	the	PC	
System	Menu	(p.36).
•	When	input	computer	signal	to	the	projector,	PC	adjust	function
will	become	available.
Mode 1
Mode 2
Mode 3
Mode 4
Mode 5
Mode 6
Mode 7
Mode 8
Mode 9
Mode 10
0
0T o tal dots                                 1344
Position H                                  255
Position V                                    34
Display area H...

40
1
2
Normal picture level preset on the projector.
Picture level with improved halftone for graphics.
U s e r   p r e s e t   p i c t u r e   a d j u s t m e n t   i n   t h e   I m a g e   a d j u s t   M e n u  
(pp.41-42).
Computer Input
Image select Menu
Press the MENU button to display the On-Screen Menu. 
Use the Point ▲▼ buttons to select Image select and 
then press the Point ► or the SELECT button.
Use the Point ▲▼ buttons to select the desired item 
and then press the SELECT button.
Image...