Eiki Projector Lc Wul100 User Manual

Setting
Setting Menu
Press the MENU button to display the On-Screen Menu.  Press the Point ▲▼ buttons to select Setting and press the Point ► or the SELECT button to access the submenu items.
1
2Use the Point ▲▼ buttons to select the desired item and then press the Point ► or the SELECT button to access the selected item.
This projector has a Setting menu that allows you to set up the other various functions described below.
3Use the Point ▲▼ buttons to select the desired item and then press the SELECT...

This function decides whether to display On-Screen Displays.
 On .........................  Show all the On-Screen displays. Use this function when you want to project images after the lamp becomes bright enough. The factory default setting is in this option. Countdown Off ....  Show the input image instead of the countdown when turning on the projector. Use this function when you want to project the image as early as possible even when the lamp is not bright enough. Off  ........................ Hide...

Setting
Capture
Capture
This function enables you to capture an image being projected to use it for a starting-up display or interval of presentations.
Select Capture and press the SELECT button.  A confirmation box appears and select ye s to capture the projected image.
After capturing the projected image, go to the Logo select function and set it to User. Then the captured image will be displayed the next time you turn on the projector.
To cancel the capture function, select ye s in the "Quit?"...

Setting
Enter a Logo PIN code
When using side controlUse the Point ▲▼ buttons on the side control to select a number. Press the Point ► button to fix the number and move the red frame pointer to the next box. The number changes to . If you fix an incorrect number, use the Point ◄ button to move the pointer to the number you want to correct, and then enter the correct number.
Repeat this step to complete entering a four-digit number.
After entering the four-digit number, move the pointer to “Set”. Press...

Change the Logo PIN code lock setting
Setting
Picture in Picture
Picture in Picture
 
Show the selected mode (Off/User 1-5) and its status (Stored /Free/ Adj .). User 1 and User 2 have stored default values. See page 30 for details.
  User setting
P in P:   Provide the images of Main picture and Sub picture at the ratio of Screen aspect in the Screen Menu. P by P:  Provide the images of Main picture and Sub picture at the ratio of 4:3.
  P in P/P by P
Selected Mode
Status (Stored /Free/ Adj .) of the...

HDMI setup
Set the Frame Lock to Main picture or Sub picture.
Frame lock
Press the SELECT button at Reset to display a confirmation box. To reset, press the SELECT button at yes.
Reset
Setting
To store the adjusted data .
Stored data
Vacant
Return to Picture in Picture menu.
This function is only used for HDMI input source.
Image
Select Normal or Enhanced to match the video range setting of your HDMI Digital RGB equipment.
Sound
HDMI:  When using the HDMI cable, select HDMI.   
Both video and audio are...

This function allows you to change brightness of the screen.
Lamp life control
Lamp control
Select the lamp operation when the total lighting time of a lamp exceeds the recommended total hours of use.
     Mode 1 .......   The lamp can be turned on even after exceeding the recommended total hours of use.     Mode 2 .......   The lamp can be turned on even after exceeding the recommended total hours of use. But the projector turns off automatically after 3 minutes.
Lamp life control
Note:
•   	
Lamp	mode...

Choose the running speed of cooling fans from the following options. Normal . . Operate in this mode under normal conditions. Max ........  Use this mode when you want to increase the cooling effect when operating the projector in high ambient temperature environment. Fan noise is louder than Normal. 
Setting
Simple mode buttons
Only these buttons are active when the simple mode is set to On. [ON, STAND-BY, SHUTTER, INPUT, MENU, AUTO PC, SCREEN, ▲, ▼ (MUTE), ◄ (VOLUME-), ► (VOLUME+), SELECT (Mouse...

Note:
	 •	Factory	default	is	Ready: 5 Min.	 •		
When	the	shutter	is	closed	while	the	Power	management	function	is	working,	the	Power	management	function	is	released.
Setting
Select a location of the infrared remote receiver of the remote control. See “Remote Control Receivers and Operating Range” on page 15 for details.
 All ........  Activate all of the receivers.
 Front & Top . .Activate both the front and top receivers.
 Top & Back ...Activate both the top and back receivers.
 Front & Back. 
Activate...

Setting
When this function is set to On, the projector will be automatically turned on just by connecting the AC power cord to the wall outlet.
Note:
Be	sure	to	turn	off	the	projector	properly	(see	“Turning	Off	the	Projector”	on	page	24).	If	the	projector	is	turned	off	in	the	incorrect	sequence,	the	Direct	on	function	does	not	work	properly.
You can emphasize a part of the projected image with this function. Use the Point ▲▼ buttons to select a pattern of the Pointer (Dot, Arrow or Finger). (p.32)
This...