Eiki Projector Lc Wul100 User Manual

⑧ DIGITAL (DVI-D) TERMINAL Connect the computer output digital signal to this terminal. The HDTV (HDCP compatible) signal can also be connected (pp.19-20).⑯ USB CONNECTOR (Series B) Use this connector when controlling a computer with the remote control of the projector. Connect the USB terminal of your computer to this connector with a USB cable (p.19).
⑭ AUDIO 2 jACK Connect the audio output (stereo) signal from 5 BNC INPUT jacks (INPUT 2 jacks). (p.21)
⑪ VIDEO INPUT jACK Connect the component or the...

① ON/STAND-By button Turn the projector on or off (pp.23-24).
② MENU button Open or close the On-Screen Menu (p.25).
⑤ Point ▲▼◄► ( VOLUME – / + ) buttons – Select an item or adjust the value in the On-Screen Menu (p.25).  – Pan the image in Digital zoom + mode (p.43).  – Adjust the volume level (with Point ◄► buttons) (p.28).
⑩ WARNING TEMP  . indicator Blink red when the internal temperature of the projector exceeds the operating range (pp.72, 79-80).
④ SHUTTER button   Close and open up the built-in...

① STAND-By button Turn the projector off (p.24).
③ ON button  Turn the projector on (p.23).
⑫ INPUT button Select a signal (pp.33-35).
⑦ L-CLICK button Act as the left mouse button for wireless mouse operation (p.32).
② SIGNAL  EMISSION indicator Light red while a signal is being sent from the remote control to the projector.
⑥ POINT ▲▼◄►( VOLUME – / +, MUTE) buttons – Select an item or adjust the value in the On-Screen Menu (p.25).  – Pan the image in Digital zoom + mode (p.43).  – Adjust the volume...

⑯
⑮
⑲
⑰
⑱
⑰ ZOOM buttons Zoom in and out the images (p.29).
㉕ D .ZOOM button Select the Digital zoom +/- mode and resize the image (p.43).
⑱ PIP button Operate the Picture in Picture function (pp.30, 55-56).
㉑  FILTER button
    Scroll the filter (p.30).
⑮ FREEZE button Freeze the picture on the screen (p.30).㉔ KEySTONE button Correct keystone distortion (pp.31, 44, 50).
⑲ ON/OFF switch
  When using the remote control, set this switch to “ON”.  Set it to “OFF” for power saving when it is not in use...

123Open the battery compartment lid.Install new batteries into the compartment.Replace the compartment lid.
Two AAA size batteriesFor correct polarity (+ and –), be sure battery terminals are in contact with pins in the compartment.
To ensure safe operation, please observe the following precautions : ● Use two (2) AAA or LR03 type alkaline batteries. ● Always replace batteries in sets. ● Do not use a new battery with a used battery. ● Avoid contact with water or liquid. ● Do not expose the remote control...

The eight different remote control codes (Code 1–Code 8) are assigned to this pr\
ojector. Switching the remote control codes prevents interference from other remote controls wh\
en several projectors or video equipment next to each other are being operated at the same time. Change\
 the remote control code for the projector first before changing that for the remote control. See “\
Remote control” in the Setting Menu on page 58.
Press and hold the MENU and a number button (1–8) for more than five seconds...

Installation
For projector positioning, see the figures below. The projector should be set perpendicularly to the plane of the screen. (for LC-WUL100)
Note:
	 •		The	brightness	in	the	room	has	a	great	influence	on	picture	quality.	It	is	recommended	to	limit	ambient	lighting	in	order	to	obtain	the	best	image.	 •	All	measurements	are	approximate	and	may	vary	from	the	actual	sizes.
100
46.1 (14.0 m)
34.6 (10.5 m)
23.0 (7.0 m)
11.4 (3.5 m)200
300
400
236
1771 1 85940
Max. Zoom
Min. Zoom
Screen Size
(W x H)...

When replacing the lens or using an optional lens, install the lens by f\
ollowing the instructions below. Ask the sales dealer for detailed information of the optional lens speci\
fications. 
Shift the lens to the central position by using the Lens shift function (p.27).1
2
Removing the lens
Lens release button
CAUTIONBe careful when handling the lens. Do not drop.
3
Installation
While pressing the Lens release button on the topof the cabinet, turn the lens counterclockwise untilit stops and pull it out...

Monitor Output
BNC
cable
DVI Output
G B R H/V V
HDMI-DVI cable
VGA cableVGA cableUSB cable
USB port
Unplug	the	power	cords	of	both	the	projector	and	external	equipment	from	the	AC	outlet	before	connecting	cables.
Cables used for connection  ( = Cables not supplied with this projector.)
• VGA Cable (One cable is supplied.) • HDMI-DVI cable  • BNC cable  • Serial Cross cable • USB cable 
Monitor Output
HDMIANALOG IN
ANALOG OUT
Serial Crosscable
CONTROL PORT
Serial out
Installation
 
See the next page...

RGB Scart21-pin Output
S-video cable
S-video OutputComposite Video
   Y - Pb/Cb - Pr/Cr
BNC cable
Unplug	the	power	cords	of	both	the	projector	and	external	equipment	from	the	AC	outlet	before	connecting	cables.
Cables used for connection ( = Cables not supplied with this projector.)
• Video cable (RCA x 1 or RCA x 3) • BNC cable (BNC x 1 or BNC x 3) • S-video cable • Scart-VGA cable   • HDMI cable 
Component Video OutputComposite      Video
Component Video  Output (Y, Pb/Cb, Pr/Cr)HDMI Output
HDMI...