Eiki Projector Lc Wnb3000n User Manual

69
MENU
►NOTE
To capture an image is available only in PC mode.
The area that can be captured is 512 x 384 dots.
Advanced Menu
Logo Capture
How to use this function?
		Select Logo Capture item in the logo 
setting menu, and press ► button.
		You can see the red frame to select 
captured area.
		Use 4 direction buttons to adjust the 
position of the frame.
		Press “MENU” to start capturing and 
display a dialog.

Image

Logo Capture In Progress. 

70
MENU
Presentation Menu
Step:
1.   Use the ▲ /▼buttons 
to select an item.
2.   Use the ◄ / ► buttons 
to select an item or 
adjust the value.
ItemSelectionDescription
AUTO CEILINGOFF / ON
Automatically invert the image when the projector is turned 
upside down, i.e. when the projector is mounted on the 
ceiling.
FRONTEXECUTENormal projection mode.
CEILINGEXECUTEMirror the image vertically, only for the projector mounted 
upside down.
REAREXECUTEMirror the image horizontally, only for projecting onto...

71
MENU
►NOTE
 The replacement warning message is set to appear after about 3000 hours \
of 
lamp use in order to maintain the initial brightness. 
 The replacement warning message is set to appear after about 2000 hours \
of 
lamp use in order to maintain the initial brightness. 
  The replacement warning message is set to appear after about 2000 hours \
of 
lamp use in order to maintain the initial brightness. 
When replacement message appears, replace the lamp with a new one as soo\
n as possible,...

72
MENU
Security Menu
Step:
1. Use the ▲ /▼buttons to 
select an item.
2. Use the ◄ / ► buttons 
to select an item or adjust 
the value.
ItemSelectionDescription
PIN LOCK 
PROTECTION
OFF
ON 1
ON 2
OFF: Turn off PIN lock protection.
ON 1:   
After plugging in AC power, you need to key in PIN 
code at the first time of use. If the AC power stays 
plugged, you do not need to key in PIN code next 
time when you use the projector.
ON 2:   
You need to key in PIN code every time when you 
turn on the...

73
MENU
Security Menu
Step:
1. Use the ▲ /▼buttons to 
select an item.
2. Use the ◄ / ► buttons to 
select an item or adjust the 
value.
ItemSelectionDescription
FILTER TIMERShow the filter use hour.
RESET FILTER
TIMEREXECUTEReset the filter timer after cleaning / changing filter.
FILTER COUNTER
500 hours
800 hours
1000 hours
Select (500 / 800 / 1000 hours) depending on the 
environment.(default : 500 hours). Please see page75.
MAC ADDR.
If purchasing LAN control module, "MAC ADDR." will be...

74
MENU
Security Menu
Step:
1.   Use the ▲ /▼buttons to 
select an item.
2.   Use the ◄ / ► buttons to 
select an item or adjust the 
value.
ItemSelectionDescription
PROJECTOR 
NAME
Default is 
Projector
Projector network setting display which shows bits that can 
be recognized by ASCII.
DHCPOFF / ON
When setting ON, projector's IP address will be assigned by 
DHCP server automatically. When setting OFF, you can use 
remote control to do setting manually.
IP
Key in IP address manually. Press...

75
MENU
►NOTE
 Please reset the Filter time only when you replace the filter.
Auto Filter Alert
Auto Filter Alert is in SECURITY category to show the air filter use time and alert user 
to change filter. Pressing ► cursor button will display a dialog. When the operating time 
reaches the set time, a warning message will appear on the screen to remind user of filter 
cleaning / replacing.
Filter Replace...
Filter has been used for more than 500 hours. 

76
MENU
PIN Key In Operation
When the projector is turned on and the 
PIN LOCK PROTECTION is set to [ON], 
the image will show as on the right side.
1.  Press the MENU button on the projector 
or remote control. Enter PIN code by 
keypad or remote control.
2. How to enter a PIN code? 
You can use control panel or remote 
control.
CONTROL PANEL REMOTE CONTROLThe control panel and remote control buttons to enter a sequence of PIN code is like the photo below.
(1) Press ◄ button: Select the [ 1 ]
(2) Press...

77
Network Control Software Application
Before Using Network Control Software1. The projector should be powered on and the LAN wire is well connected to\
 projector.
2. The LAN module ON/OFF item in SECURITY menu of OSD should be setting ON.
3. Make sure the computer and projector can connect to network. Network \
Control software needs to 
arrange in TCP/IP network communication and the network cable.
►NOTE: 
         IE8 browser & 1024x768 viewing resolution is recommended.
Procedure to utilize this...

78
Network Control Software Application
Browser Control
Auto IP address setting (while DHCP setting is "ON"):
(1) Enable DHCP from the projector on-screen-display menu, under "SECURITY  LAN SETTING".
(2) Please wait for the PC server to release IP address to the projector.
(3)  Enter  "Given  IP  address  (For  example  http://192.168.1.176/)"  into  the  address  bar  of  the  web  browser  and 
press “Enter” key or click “Go” button.
Item Setting description:
ITEM...