Eiki Projector Lc Wnb3000n User Manual

							69
MENU
►NOTE
To capture an image is available only in PC mode.
The area that can be captured is 512 x 384 dots.
Advanced Menu
Logo Capture
How to use this function?
		Select Logo Capture item in the logo 
setting menu, and press ► button.
		You can see the red frame to select 
captured area.
		Use 4 direction buttons to adjust the 
position of the frame.
		Press “MENU” to start capturing and 
display a dialog.

Image

Logo Capture In Progress. 
						

							70
MENU
Presentation Menu
Step:
1.   Use the ▲ /▼buttons 
to select an item.
2.   Use the ◄ / ► buttons 
to select an item or 
adjust the value.
ItemSelectionDescription
AUTO CEILINGOFF / ON
Automatically invert the image when the projector is turned 
upside down, i.e. when the projector is mounted on the 
ceiling.
FRONTEXECUTENormal projection mode.
CEILINGEXECUTEMirror the image vertically, only for the projector mounted 
upside down.
REAREXECUTEMirror the image horizontally, only for projecting onto rear 
projection screen.
CEILING AND 
REAREXECUTEMirror the image horizontally and vertically. Projecting onto 
a rear projection screen while projector is upside down.
LAMP MODENORMAL / 
ECOSwitch lamp mode between Normal or ECO mode.
LAMPShow lamp use time.
RESET LAMP 
TIMEREXECUTEAfter changing a new lamp, execute this function to reset 
the lamp timer.
POWER 
MANAGEMENT
15/30/60/off/
MinutesSet power off time after detecting no signal. 
						

							71
MENU
►NOTE
 The replacement warning message is set to appear after about 3000 hours \
of 
lamp use in order to maintain the initial brightness. 
 The replacement warning message is set to appear after about 2000 hours \
of 
lamp use in order to maintain the initial brightness. 
  The replacement warning message is set to appear after about 2000 hours \
of 
lamp use in order to maintain the initial brightness. 
When replacement message appears, replace the lamp with a new one as soo\
n as possible, even if 
the lamp is still workable.
Presentation Menu
Reset Lamp Timer
The lamp timer is the time counted after the last resetting. The usage time of the lamp 
is shown in the PRESENTATION Menu. Pressing the RESET button or the ► button 
displays a dialog.
To reset the lamp time, select the RESET using the ► button. 
						

							72
MENU
Security Menu
Step:
1. Use the ▲ /▼buttons to 
select an item.
2. Use the ◄ / ► buttons 
to select an item or adjust 
the value.
ItemSelectionDescription
PIN LOCK 
PROTECTION
OFF
ON 1
ON 2
OFF: Turn off PIN lock protection.
ON 1:   
After plugging in AC power, you need to key in PIN 
code at the first time of use. If the AC power stays 
plugged, you do not need to key in PIN code next 
time when you use the projector.
ON 2:   
You need to key in PIN code every time when you 
turn on the projector.
 CAUTION:
Once the PIN code had been set, the projector cannot be 
used unless you enter the correct PIN code.
 
MODIFY PINEXECUTE
1. Press “ MENU ” on the projector or remote control.
2.   Use the ► button to select the MODIFY PIN item of the 
SECURITY category.
3.  Press the ► button to change PIN LOCK PROTECTION 
mode.
4. Please enter the original PIN code.
    (a)   If the PIN is correct, system will allow you to change 
a new PIN code.
    (b)   If the PIN is incorrect, a “ Code Error ” message will appear.
5. Please enter a new PIN code. And then enter again to confirm.
NOTE:
(1)  
To change the PIN lock protection state, you must 
enter the PIN code first.
(2) Please enter: 0000 for first-time use.
(3)    To avoid unnecessary trouble, if you activate the [PIN 
Lock Protection], it is highly recommended that you 
write down the PIN code and store it in a safe place. 
						

							73
MENU
Security Menu
Step:
1. Use the ▲ /▼buttons to 
select an item.
2. Use the ◄ / ► buttons to 
select an item or adjust the 
value.
ItemSelectionDescription
FILTER TIMERShow the filter use hour.
RESET FILTER
TIMEREXECUTEReset the filter timer after cleaning / changing filter.
FILTER COUNTER
500 hours
800 hours
1000 hours
Select (500 / 800 / 1000 hours) depending on the 
environment.(default : 500 hours). Please see page75.
MAC ADDR.
If purchasing LAN control module, "MAC ADDR." will be 
shown in "Security" Menu. 
MAC address stands for unique Media Access Control 
address of LAN control module and displays with six 
groups of two hexadecimal digits.
CLOSED CAPTION
OFF(Default)
C.C1
C.C2
C.C3
C.C4
T1
T2
T3
T4
The Closed Caption function intimates the sound effects, 
dialogue, and narration in the content of the television 
program or video source.
Caption (C.C1~C.C4) : Display closed caption Text 
(T1~T4) : Display text data, which is for additional 
information such as news reports or a TV program guide.
NOTE :   
This function is available only in video / S-Video 
source.
LAN MODULEOFF
ON
If purchasing LAN control module, "LAN MODULE" will 
be shown in "Security" Menu.
Select ON/OFF to turn on/off LAN control feature.
LAN SETTINGEXECUTEEnter LAN SETTING to set up projector network 
configuration. 
						

							74
MENU
Security Menu
Step:
1.   Use the ▲ /▼buttons to 
select an item.
2.   Use the ◄ / ► buttons to 
select an item or adjust the 
value.
ItemSelectionDescription
PROJECTOR 
NAME
Default is 
Projector
Projector network setting display which shows bits that can 
be recognized by ASCII.
DHCPOFF / ON
When setting ON, projector's IP address will be assigned by 
DHCP server automatically. When setting OFF, you can use 
remote control to do setting manually.
IP
Key in IP address manually. Press "ENTER" to do digit 
setting. When appears, press ▲ /▼ to adjust value. When 
finishing value adjustment, press MENU to exit.
MASK
Enter MASK address manually. Press "ENTER" to do digit 
setting. When appears, press ▲ /▼ to adjust value. When 
finishing value adjustment, press MENU to exit.
GATEWAY
Enter GATEWAY address manually. Press "ENTER" to do 
digit setting. When appears, press ▲ /▼ to adjust value. 
When finishing value adjustment, press MENU to exit. 
						

							75
MENU
►NOTE
 Please reset the Filter time only when you replace the filter.
Auto Filter Alert
Auto Filter Alert is in SECURITY category to show the air filter use time and alert user 
to change filter. Pressing ► cursor button will display a dialog. When the operating time 
reaches the set time, a warning message will appear on the screen to remind user of filter 
cleaning / replacing.
Filter Replace...
Filter has been used for more than 500 hours. 
						

							76
MENU
PIN Key In Operation
When the projector is turned on and the 
PIN LOCK PROTECTION is set to [ON], 
the image will show as on the right side.
1.  Press the MENU button on the projector 
or remote control. Enter PIN code by 
keypad or remote control.
2. How to enter a PIN code? 
You can use control panel or remote 
control.
CONTROL PANEL REMOTE CONTROLThe control panel and remote control buttons to enter a sequence of PIN code is like the photo below.
(1) Press ◄ button: Select the [ 1 ]
(2) Press ▲ button: Select the [ 2 ]
(3) Press ► button: Select the [ 3 ]
(4) Press ▼ button: Select the [ Enter ] move to next row.(4~6,7~9, ~OK)
(5)   Press  (backspace) item: In case you enter a wrong digit, select  to delete the wrong digit you entered.
(6)  Press  item: Once all four digits of the PIN are entered, select  to confirm.
►NOTE
(1) Please enter: 0000 for first-time use.
(2)  If the PIN is incorrect, a "Enter new code" message will be shown. Pleas\
e try again. If the PIN 
code input is incorrect for three times, a warning message will show up \
and the  projector will 
shut itself down in 30 seconds.
(3)  If you have no idea about the PIN, please contact your dealer for help. 
						

							77
Network Control Software Application
Before Using Network Control Software1. The projector should be powered on and the LAN wire is well connected to\
 projector.
2. The LAN module ON/OFF item in SECURITY menu of OSD should be setting ON.
3. Make sure the computer and projector can connect to network. Network \
Control software needs to 
arrange in TCP/IP network communication and the network cable.
►NOTE: 
         IE8 browser & 1024x768 viewing resolution is recommended.
Procedure to utilize this function
It can help user to monitor and manage the projector(s) status in the \
local area network.
	 
Register the projector(s) which needs to be controlled. " Auto search " can help you to seek the projector(s) source easily. After registering in the work group, you can start to control the projec\
tor.
		Group the projector(s) into different sections. You can monitor the status easily by the sort of group name function in t\
he network.
		Monitor the status for each projector. a.You can manage and change the monitoring content by System Parameter Sett\
ing. b. The Lamp timer, filter working time or system warning feedback etc. can be known by checking the status for projector(s).
		Control the booked projector(s). The status can be refreshed and acquired by monitoring functions; you ca\
n also operate the function easily by Network Control.
►NOTE
To  monitor  and  control  the  projector(including  stand-by  mode),  the  following conditions need to be ready:
(1) Projector should already be powered on.(2) Projector is connected to network.(3)   LED  light  of  the  projector  network  port  shows  normal.  (Green  light  on,  Orange twinkle)
*  Stand-by mode indictor: Green LED (Power) on the projector’s control panel flashes.
LAN 
						

							78
Network Control Software Application
Browser Control
Auto IP address setting (while DHCP setting is "ON"):
(1) Enable DHCP from the projector on-screen-display menu, under "SECURITY  LAN SETTING".
(2) Please wait for the PC server to release IP address to the projector.
(3)  Enter  "Given  IP  address  (For  example  http://192.168.1.176/)"  into  the  address  bar  of  the  web  browser  and 
press “Enter” key or click “Go” button.
Item Setting description:
ITEM SETTINGDESCRIPTIONHome (Status)Show current projector status and network configuration settings.Control PanelSelect projector’s detailed setting from this page.NetworkSet up network configuration and password from this page.Alert SettingShow and setup Alert configurations.
ScheduleShow and set up Schedule, including Weekly Schedule and Specific Day.TimeSet up the date/time on the projector.CrestronCrestron configuration.LogoutLogout information.
If the Administrative & User password is enabled, select your User Name and ent\
er password to login.