Eiki Projector Lc Wgc500a User Manual

71
Troubleshooting
Before calling your dealer or service center for assistance, check the items below once again.
– Make sure you have properly connected the projector to peripheral equipment as described \
on pages 20–22. 
–  Make sure all equipment is connected to AC outlet and the power is turned on.
–  When the projector does not project an image from the connected computer\
, restart the computer.  
 Problem:  – Solutions
  No power  – Plug the power cord of the projector into the AC outlet. 
    –...

72
   – Projecting from the excessive slant angle to the screen may cause    
     keystone distortion and partial imperfect focus.
  Picture is not bright enough .  – Check if "Contrast" or "Brightness" are adjusted properly See page 42. 
    – Check if "Image level" is selected properly See page 41. 
    –   Check the LAMP 1/2 REPLACE indicators. If it lights, the end of lamp 
life is approaching. Replace the lamp with a new one promptly. See 
pages 66-68, 78.
    – Check the...

73
Appendix
This symbol on the nameplate means the product 
is Listed by Under writers Laboratories Inc. It is 
designed and manufactured to meet rigid U.L. 
safety standards against risk of fire, casualty and 
electrical hazards.The CE Mark is a Directive 
conformity mark of the European 
Community (EC).
WARNING :
High voltages are used to operate this projector . Do not attempt to open the cabinet .
If problems still persist after following all operating instructions, contact the dealer where you...

74
Menu Tree
Dynamic
RealCinema*Image 1Image 2Image 3
Image
Input
Go to System (3)
Go to System (3)
Video 
Go to System (1)
S-video
Standard
Quit
Input 1
Go to System (3)Video
Go to System (1)Input 2 RGB
Go to System (2)Component
Image 4
RGB (PC analog)
RGB (Scart)
HDMI
Quit
Quit
SySTEM (3)SySTEM (1)
- - - -
Mode 1
Mode 2
XGA 1SECAM
NTSC
Auto
PAL
PAL-M
PAL-N
NTSC4.43
SySTEM (2)
1035i
720p
Auto
1080i
480p
575i
575p
480i
Quit
0–630–63
Off/L1/L2/Film
Image AdjustContrastBrightnessColorTint...

75
InputH-sync freq.V-sync freq.
PIN code lock
Information
Key lock
Screen
Language
Power management
Security
Remote control 
Lamp mode
Lamp control
Lamp 1
Lamp 2
Filter counter
Shutter managementRemote control
(    ) Min
Projector
SERIAL NO.
Auto PC adj.
Total dotsHorizontalVertical
Display area HDisplay area VReset
PC Adjust
Yes/No
Clamp
Current mode
Mode free/Store
Quit
Fine sync0–31
Mode 1
H-sync freq.V-sync freq.Quit
NormalTrueFull 
Screen
✔Note:
	 •	The	Menu	display	varies	depending	on	the	input...

76
Appendix
LanguageSetting12 languages provided
Blue/User/Black
Auto 1/Auto 2/High
/Normal/Eco 1/Eco 2
Background
Lamp control
Quit
Capture
Logo PIN code change
Logo PIN code lock
Quit
QuitLogo selectLogo
Off/Default/User
Yes/No
On/Off
Off/Ready/Shutdown
Code 1–Code 8
Power management
Remote control
Timer (1–30 Min)Quit
Spotlight/PointerPointerQuit
All/Front&Top/Top&Back/
Front&Back//Front/Top/BackRC sensor
Off/Countdown off/On Display
On/OffOn startSlantOff/L1/L2/L3/L4
Lamp 1/Lamp 2Lamp mode
Lamp...

77
Indicators and Projector Condition
Check the indicators for the projector condition.  
The projector is operating normally .
• • • on
• • • off• • •  
blinking at the normal rate       
(approx. 1 second ON,         
1 second OFF)
• • •  blinking slow           
(approx. 2 seconds ON, 
2 seconds OFF)
• • • blinking fast              
(approx. 0.5 seconds ON,  
0.5 seconds OFF)
Indicators
Projector ConditionPOWER
green / red WARNING
TEMP.red WARNING
FILTER
orange SHUTTER
blue LAMP 1/2
REP. 
yellow
The...

78
The projector is detecting abnormal condition .
Indicators
Projector ConditionPOWER
green / red WARNING
TEMP.red WARNING
FILTER
orange SHUTTER
blue LAMP 1/2
REP.
yellow
The temperature inside the projector is elevated close to 
the abnormally high level.
The temperature inside the projector is abnormally high. 
The projector cannot be turned on. When the projector 
is cooled down enough and the temperature returns to 
normal, the POWER indicator lights red and the projector 
can be turned on. (The...

79
The projector is detecting abnormal condition .
Indicators
Projector ConditionPOWER
green / red WARNING
TEMP.red WARNING
FILTER
orange SHUTTER
blue LAMP 1/2
REP.
yellow
If the Filter counter reached a time set in the timer 
setting, a Filter replacement icon (Fig.2) appears on the 
screen and the WARNING FILTER indicator on the top 
panel lights up. Replace the filter as soon as possible. If 
the filter is out of scroll and the projector reaches a time 
set in the timer setting, Fig. 3 appears on the...

80
Compatible Computer Specifications
Basically this projector can accept the signal from all computers with th\
e V- and H-Frequency mentioned 
below and less than 140 MHz of Dot Clock.
 
Appendix
ON-SCREEN DISPLA yRESOLUTION H-Freq .
(kHz) V-Freq .
(Hz)
VGA 1 640x480 31.470 59.880 
VGA 2 720x400 31.470 70.090 
VGA 3 640x400 31.470 70.090 
VGA 4 640x480 37.860 74.380 
VGA 5 640x480 37.860 72.810 
VGA 6 640x480 37.500 75.000 
VGA 7 640x480 43.269 85.000 
MAC LC13 640x48034.970 66.600 
MAC 13 640x480...