Eiki Projector Lc Wgc500a User Manual

51
Enter a Logo PIN code
After a correct Logo PIN code 
is entered, the following dialog 
box appears.
Change the Logo PIN code
Logo PIN code can be changed to your desired four-digit 
number. Press the Point 
d button to select “Logo PIN 
code change” and then press the SELECT button. The 
New Logo PIN code input dialog box appears. Set a new 
Logo PIN code.  
Be sure to note the new Logo PIN code and keep it on 
hand. If you lost the number, you could no longer change 
the Logo PIN code setting. For...

52
Picture in Picture
This function is used to project two videos simultaneously 
by placing a separate small sub screen within the main 
screen.
Use the Point ed buttons to move the red frame 
pointer to Picture in Picture and then press the 
SELECT button to display a dialog box. Use the Point 
7 8 buttons to adjust the setting mode.
✔Note:
•		The 	Picture 	in 	Picture 	function 	is 	not 	available	
depending	 on	the	 input	 signals	 and	the	selected	
input	 terminals.	 Refer	to	‘List	 of	Picture	 in...

53
Setting
This Projector is equipped with 2 Projection Lamps.  This 
function allows you to choose how to use the lamp as follows. 
 Lamp1 ............ Always use Lamp 1.
  Lamp2  ........... Always use Lamp 2.
  Lamp1/2 .........  Automatically switch the active lamp from one  
lamp to the other .
✔Note:
	 •	 	 When	Lamp	1	or	Lamp	2	mode	is	switched	to	Lamp	
1/2	mode,	the	active	lamp	changes	after	the	total	
lighting	time	of	a	currently	used	lamp	exceeds	10	
hours.	
	 •	 When	the	total	lighting	time	of...

54
Setting
Lamp control
This function allows you to change brightness of the screen.Auto 1 ......... The brightness according to the input signal 
(between Normal and Eco mode).
Auto 2 .........  The brightness according to the input signal 
(between High and Eco mode).
High ............  Brighter than the Normal mode.
Normal  .......  Normal brightness 
  Eco 1 ..........  
Lower brightness and Fan speed decrease. 
Lower brightness reduces the lamp power 
consumption and extends the lamp life.
 Eco 2...

55
Setting
Pointer
You can emphasize a part of the projected image with 
this function. Use the Point 
ed buttons to choose either 
Spotlight or Pointer and press the SELECT button. Then 
use the Point 
7 8 buttons to select a size of the Spotlight 
(Large, Middle, or Small) or a pattern of the Pointer (Arrow, 
Finger, or Dot). (See page 32 for operation.)
Pointer
Remote control
Remote control
The eight different remote control codes (Code 1–Code 8) 
are assigned to the projector; the factory-set,...

56
Setting
Display
This function decides whether to display On-Screen Displays.
 On ............................  Show all the On-Screen displays. Use 
this function when you want to project 
images after the lamp becomes bright 
enough. The factory default setting is 
in this option.
  Countdown Off ........  Show the input image instead of 
the countdown when turning on the 
projector. Use this function when you 
want to project the image as early as 
possible even when the lamp is not 
bright enough....

57
Setting
Press the SELECT button at 
Power management and this 
dialog box appears. Use the 
Point 
7 8 buttons to choose 
one of the three options. 
Press the Point 
d button to 
select the timer, and then use 
the Point 
7 8 buttons to set 
timer.
Power managementSelect one of the following options:
  Ready .................  When the lamp has been fully cooled 
down, the POWER indicator changes to fast 
blinking. In this condition, the projection 
lamp can be turned on if the input signal 
is...

58
Setting
Shutter
Shutter function is available to block out light to the 
screen, so that the screen can be used for the other 
presenters.Prohibits the shutter operation from the remote control 
and the projector's top control.
Remote control    ...   Selecting "On" prohibits the shutter 
operation from the remote control. 
Projector . . . . .  ...   Selecting "On" prohibits the shutter 
operation from the top control.
It is possible to prohibit the shutter operation from both of...

59
Key lock
Select Key lock. Use the Point 
ed buttons to choose one of 
the options and select [Yes] 
to activate it.
Security (Key lock and PIN code lock settings)
This function allows you to use the Key lock and PIN code 
lock function to set the security for the projector operation.
Key lock
This function locks the top control and remote control 
buttons to prevent operation by unauthorized persons.
 ..... Unlocked
 .....  Lock all the top control buttons
 .....  Lock the top control buttons except...

60
Setting
Change the PIN code lock setting
Use the Point 7 8 buttons to 
switch between the options.
Enter a PIN code
PIN code lock
This function prevents the projector from being operated 
by unauthorized persons and provides the following 
setting options for security.
  Off ...........  Unlocked.
  On1 ..........  Enter the PIN code every time turning on 
                    the projector.
  On2 ..........  Enter the PIN code to operate the projector 
once the power cord is disconnected; as 
long as...