Eiki Projector Lc Wb42na User Manual

41

Video	Input
Choose Computer	1	by pressing the INPUT button on the top control or press the COMPUTER button on the 
remote control; choose HDMI by pressing the INPUT button on the top control or press the HDMI button on the 
remote control. 
Before using these buttons, correct input source should be selected through Menu operation as described 
below.
1
Input	Menu
2Use the Point ▲▼ buttons to select  Computer	1 and 
then press the Point ► button; use the Point ▲▼ 
buttons to select HDMI, and then...

42

Video	InputVideo	System	Selection
1AV	System	Menu	(Video	or	S-video)
AV	System	Menu	(Component)
2
If the projector cannot reproduce proper video image, 
select a specific broadcast signal format from among PAL, 
SECAM,	NTSC
,  NTSC	4 .43, PAL-M and 	PAL-N.
PAL/SECAM/NTSC/NTSC4 .43/PAL-M/PAL-N
The projector automatically detects an incoming video 
signal, and adjusts itself to optimize its performance.
If the projector cannot reproduce proper video image, select 
a specific component video signal...

43

Image	Select	Menu
Select the desired image mode among Dynamic, Standard, 
Cinema, Blackboard	(Green), Colorboard, Image	1, 
Image	2
,  Image	3 and  Image	4 by pressing the IMAGE 
button on the remote control.
Standard
Picture mode adjusted with fine tone.
Cinema
Blackboard	(Green)
Image	1–4
IMAGE	button
Dynamic
Cinema
Image	Mode	Selection	
Blackboard	(Green)
Dynamic
Standard
Remote	Control
IMAGE	button
Direct	Operation
For viewing pictures in a bright room.
Normal picture mode preset on the...

44

Video	InputImage	 Adjustment
1
2
Press the Point ◄ button to decrease the contrast; press the 
Point ► button to increase the contrast (from 0 to 63).
Press the Point ◄ button to decrease the brightness; press  
the Point ► button to increase the brightness (from 0 to 63).
Contrast
Brightness
Press the Point ◄ button to lighten red tone; press the Point 
► button to deepen red tone (from 0 to 63).
White	balance	(Red)
Press the Point ◄ button to lighten green tone; press the 
Point ► button to deepen...

45

Video	Input
Use  the  Point ◄►  buttons  to  adjust  the  gamma  value  to 
obtain a better balance of contrast (from 0 to 15).
Gamma
Press the Point ◄ button to decrease the sharpness of the 
image; press the Point ► button to increase the sharpness 
of the image (from 0 to 15).
Sharpness
An interlaced video signal can be displayed in progressive 
mode. Select one of the following options.
 Off .........  Disabled.
 L1  ..........  For an active picture.
 L2  ..........  For a still picture.
 Film...

46

Video	Input
This projector has the picture screen resize function, which enables you to customize the image size.
Normal
Screen	Size	Adjustment
Screen	Menu1
2
Provide the image to fit the screen size while maintaining
the aspect ratio of input signal.
Custom
Adjust the screen scale and position manually with this 
function.
Press the Point ► button at Custom and the Custom is
displayed on the screen, you can use the Point ▲▼ buttons
to choose the item you want to adjust.
 Scale	H/V  .............

47

HDMI setupTerminal                                                        Computer 2Pointer                                                          DotStandby mode                                               Eco

Language
The language used in the On-Screen Menu is available in 
English,	German,	French,	Italian,	Spanish,	Portuguese, 
Dutch,	Swedish,	Finnish,	Polish, Hungarian,	Romanian, 
Russian,	Chinese,	Korean,  japanese	and Thai.
Setting	Menu
Setting
Setting
HDMI setupTerminal...

48

Setting
Note:
 • Auto	Keystone corrects vertical distortion only, not 
correct horizontal distortion.
  • The  Auto	Keystone
 function cannot work when the 
Ceiling feature is set On in the Setting menu (p.53).
  • Perfect correction of the image distortion cannot 
be ensured with the Auto setup function. If the 
distortion is not corrected properly by pressing the 
AUTO SETUP/CANCEL button, adjust manually 
by pressing the KEYSTONE button on the remote 
control or selecting Keystone in the Setting...

49

Keystone
This function is used to store or reset the keystone 
correction when the AC power cord is unplugged.
 Store .......  Keep the keystone correction even when the 
AC power cord is unplugged.
 Reset  .......  Release the keystone correction when the AC 
power cord is unplugged.
To correct keystone distortion, press the SELECT button. 
Keystone appears on the screen. Use the Point ▲▼ 
buttons to correct keystone distortion (p.26).
Background
Select the background screen for when no input...

50

Setting
Logo	(Logo	and	Logo	PIN	code	lock	settings)
HDMI setupTerminal                                                        Computer 2Pointer                                                          DotStandby mode                                               Eco
Logo	select
This function allows you to customize the screen logo with 
Logo	select
, capture, Logo	PIN	code	lock and  Logo	PIN	
code	change
 functions.
Note:
    When 
On is selected in the Logo PIN code lock function, 
Logo	select
,...