Eiki Projector Lc Wb42na User Manual

11

Part	Names	and	Functions
Top	Control
⑩ LAMP 	REPLACE	indicator
  Lights yellow when the projection lamp reaches its 
end of life (pp.67, 75).
⑥ WARNING	indicator
  – Lights red when the projector detects an abnormal 
condition. 
  – Blinks red when the internal temperature of the 
projector exceeds the operating range (pp.64, 75).
⑨ ON/STAND–By	button
Turn the projector on or off (pp.21-23).
⑤ POWER	indicator
  – Lights red when the projector is in stand-by mode.
  – Lights green during operations....

12

Part	Names	and	Functions
㉘ NETWORK	button
      Select the Network input. See the owner's manual of “Network Set-up and 
Operation” and owner's manual of "Memory viewer function".
Note:To ensure safe operation, please observe the following precautions:
–  Do not bend, drop, or expose the remote control to 
moisture or heat.
–  For cleaning, use a soft dry cloth. Do not apply 
benzene, thinner, spray, or any chemical material.
Remote	Control
①
⑧
⑮
⑪
⑤②
⑨
⑩
⑭
⑰
⑥
⑦
⑫
⑬
⑯
④
②...

13

Part	Names	and	Functions
To ensure safe operation, please observe the following precautions :
 ● Use two (2) AAA or LR03 type alkaline batteries.
  ● Always replace batteries in sets.
  ● Do not use a new battery with a used battery.
  ● Avoid contact with water or liquid.
  ● Do not expose the remote control to moisture or heat.
  ● Do not drop the remote control.
  ● If the battery has leaked on the remote control, carefully wipe the case clean and install new batteries.
  ● Risk of an explosion...

14

Part	Names	and	Functions
Spotlight
Pointer	Function
Pointer
Laser	Pointer	Function
LASER button
PRESENTATION POINTER 
button
This remote control emits a laser beam from the laser light window. Press the LASER button to activate the 
laser pointer. The signal emission indicator lights red and the red laser beam is emitted. If the LASER button is 
pressed for more than one minute or if it is released, the laser light goes of f.
The laser emitted is a Class II laser. Do not look into the laser light...

15

Part	Names	and	Functions
Adjustable	Feet
Projection angle can be adjusted up to 8.9 degrees with the 
adjustable feet. 
Lift the front of the projector and pull the feet lock latches on 
both side of the projector.
Release the feet lock latches to lock the adjustable feet and 
rotate the adjustable feet to a proper height and tilt.
Keystone  distortion  can  be  adjusted  automatically  with  the 
Auto setup function or manually by using the remote control 
or the menu operation (see pages 26,...

16

Positioning	the	Projector
For  projector  positioning,  see  the  figures  below. The  projector  should  be  set  perpendicularly  to  the  plane  of  the 
screen.
Installation
Note:
  • The brightness in the room has a great influence on picture quality. It is recommended to limit ambient 
    lighting in order to obtain the best image.
 • All measurements are approximate and may vary from the actual sizes.
A
B
100
150
200189
127
95
63
300(wide)
40
300(tele)
39.7(12.1m)
25.2(7.7m)
16.7(5.1m)...

17

InstallationInstallation
Connecting	to	a	Computer
Cables	used	for	connection	
• VGA cables (Mini D-sub 15 pin) * 
• USB cable
• Audio cables
• HDMI-DVI cable
(*One cable is supplied; other cables are not supplied with the projector.)
Note:
  • Input sound to the COMPUTER1 COMPONENT/COMPUTER 
2  AUDIO IN terminal when using the COMPUTER IN 1/ 
COMPONENT IN and the COMPUTER IN 2/MONITOR OUT 
terminal as input.
  • When the AUDIO OUT is plugged-in, the projector's built-in 
speaker is not...

18

Installation
Connecting	to	Video	Equipment
Cables	used	for	connection		
• Video and Audio cable (RCA x 3) 
• S-video cable 
• Audio cable 
(Cables are not supplied with the projector. )
Unplug the power cords of 
both the projector and external 
equipment from the AC outlet 
before connecting cables.
Note:
    
When the AUDIO OUT is plugged-in, the projector's built-
in speaker is not available.
ONON
External Audio Equipment
Audio cable   (stereo)
VIDEOS-video
S-video cable  Video and Audio...

19

Installation
Connecting	to	Component	Video	Equipment
Note:
  • When the AUDIO OUT is plugged-in, the projector's 
built-in speaker is not available.
  • See page 80 for ordering optional cables.
Unplug the power cords of 
both the projector and external 
equipment from the AC outlet 
before connecting cables.
External Audio Equipment
COMPUTER 1 COMPONENT/AUDIO IN
Audio cable (stereo)
Audio cable (stereo)
Audio Input
Component Video Output(Y, Pb/Cb, Pr/Cr)
RGB Scart 21-pin Output
Audio Output...

20

InstallationConnecting	the	 AC	Power	Cord
This projector uses nominal input voltages of 100-120 V or 
200–240 V AC and it automatically selects the correct input 
voltage. It is designed to work with single-phase power 
systems having a grounded neutral conductor. To reduce 
the risk of electrical shock, do not plug into any other type of 
power system.
If you are not sure of the type of power being supplied, 
consult your authorized dealer or service station.
Connect the projector with all...