Eiki Projector Lc Sxg400 User Manual

61
The WARNING indicators show the state of the function which protects the projector. Check the state of the 
WARNING indicators and the POWER indicator to take proper maintenance. 
Warning Indicators
The projector is shut down and the WARNING TEMP. 
indicator is blinking red.
When the temperature inside the projector reaches a 
certain level, the projector will be automatically shut 
down to protect the inside of the projector. The POWER 
indicator is blinking while the projector is being cooled 
down....

62
Unplug the AC power cord before cleaning.
Gently wipe the projection lens with a cleaning cloth that 
contains a small amount of non-abrasive camera lens cleaner, 
or use a lens cleaning paper or commercially available air 
blower to clean the lens. 
Avoid using an excessive amount of cleaner. Abrasive 
cleaners, solvents, or other harsh chemicals might scratch 
the surface of the lens.
When the projector is not in use, replace the lens cap.
Cleaning the Projector Cabinet
Unplug the AC power cord...

63
Troubleshooting
Before calling your dealer or service center for assistance, check the items below once again.
– Make sure you have properly connected the projector to peripheral equipment as described \
on pages 20–22. 
–  Make sure all equipment is connected to AC outlet and the power is turned on.
–  When the projector does not project an image from the connected computer\
, restart the computer.  
 Problem:  – Solutions
  No power  – Plug the power cord of the projector into the AC outlet. 
    –...

64
   – Projecting from the excessive slant angle to the screen may cause    
     keystone distortion and partial imperfect focus. See page 18.
  Picture is not bright enough .  – Check if "Contrast" or "Brightness" are adjusted properly See page 42. 
    – Check if "Image level" is selected properly See page 41. 
    – Check the LAMP REPLACE indicator. If it lights, the end of lamp life is 
     approaching. Replace the lamp with a new one promptly. See pages 
     59-60, 69....

65
Appendix
This symbol on the nameplate means the product 
is Listed by Under writers Laboratories Inc. It is 
designed and manufactured to meet rigid U.L. 
safety standards against risk of fire, casualty and 
electrical hazards.The CE Mark is a Directive 
conformity mark of the European 
Community (EC).
WARNING :
High voltages are used to operate this projector . Do not attempt to open the cabinet .
If problems still persist after following all operating instructions, contact the dealer where you...

66
Menu Tree
Dynamic
RealCinemaImage 1Image 2Image 3
Image
VolumeMuteQuitOn/OffSound0–63
Input
Input 3Auto
Go to System (3)
Go to System (3)
Video 
Go to System (1)
S-video
Standard
Quit
Input 1
Go to System (3)Video
Go to System (1)Input 2 RGB
Go to System (2)Component
Image 4
RGB (PC Analog)
RGB (Scart)
RGB (PC Digital)
RGB (AV HDCP)
Quit
Quit
SySTEM (3)SySTEM (1)
- - - -
Mode 1
Mode 2
XGA 1SECAM
NTSC
Auto
PAL
PAL-M
PAL-N
NTSC4.43
SySTEM (2)
1035i
720p
Auto
1080i
480p
575i
575p
480i
InputH-sync...

67
LanguageSetting12 languages provided
Blue/User/BlackAuto 1
Normal
BackgroundLamp control
Quit
Capture
Logo PIN code change
Logo PIN code lock
Quit
Auto 2High
QuitAuto PC adj.
Total dotsHorizontalVertical
Display area HDisplay area VReset
PC Adjust
Yes/No
Clamp
Current mode
Mode free/Store
Quit
Fine sync0–31
Mode 1
H-sync freq.V-sync freq.Quit
NormalTrueWideFull screen
Screen
Logo selectLogoOff/Default/User
Yes/No
On/Off
Eco 1Eco 2
✔Note:
	 •	The	Menu	display	varies	depending	on	the	input	 signal.
Mode...

68
Check the indicators for the projector condition.  
• • • lighting• • • off• • • blinking
Indicators and Projector Condition
WARNING TEMP . indicator
Appendix
Indicators
Projector ConditionPOWER
green LAMP
red WARNING
TEMP.red
The projector is off. (The AC power cord is unplugged.)
The projector is in stand-by mode. Press the ON/STAND-BY button to 
turn on the projector.
The projector is operating normally.
The projector is in the Power management mode.
The projector is preparing for stand-by or the...

69
* When the projection lamp reaches its end of life, the LAMP REPLACE indicator lights yellow. When this indicator lights 
yellow, replace the projection lamp with a new one promptly. Reset the lamp counter after replacing the lamp. See pages 
59–60.
––
––
WARNING
FILTER
orange
The filter is clogged. Stop using the projector immediately and clean 
or replace the filter (see below).
Projector ConditionPOWERgreen
Indicators
WARNING FILTER indicator
The Filter counter reached a set time. Clean or replace...

70
Compatible Computer Specifications
Basically this projector can accept the signal from all computers with th\
e V- and H-Frequency mentioned 
below and less than 165 MHz of Dot Clock. PC Adjustment is limited when selecting these modes.
Appendix
ON-SCREEN 
DISPLA yRESOLUTION H-Freq .
(kHz) V-Freq .
(Hz)
VGA 1 640x480 31.470 59.880 
VGA 2 720x400 31.470 70.090 
VGA 3 640x400 31.470 70.090 
VGA 4 640x480 37.860 74.380 
VGA 5 640x480 37.860 72.810 
VGA 6 640x480 37.500 75.000 
VGA 7 640x480 43.269 85.000...