Eiki Projector Lc Sxg400 User Manual

11
Rear Terminal
t	USB CONNECTOR (Series B)
  Use this connector when controlling a computer 
with the remote control of the projector. Connect 
the USB terminal of your computer to this 
connector with the supplied USB cable (p.20).
y	S-VIDEO INPUT JACK
  Connect the S-VIDEO output signal from video 
equipment to this jack (p.21).
i	AUDIO 2 JACK
  Connect the audio output (stereo) signal from a 
computer or video equipment connected to q to 
this jack (pp.20–22).
o	AUDIO 1 JACK
  Connect the audio...

12
!0	R/C JACK
  When using the wired remote control, connect the 
wired remote control to this jack with a remote 
control cable (supplied).
!2	MONITOR OUTPUT TERMINAL (ANALOG)
  This terminal outputs the video signal from 
computer to external video equipment (p.20).
✽	RESET button
  A  built-in  micro  processor  which  controls  this  unit 
may occasionally malfunction and need to be reset. 
This  can  be  done  by  pressing  the  RESET  button 
with  a  pen,  which  will  shut  down  and  restart...

13
q
w
e
t
u
i
o
w	LAMP REPLACE indicator
  Lights yellow when the projection lamp reaches its 
end of life (pp.59, 69).
q	WARNING TEMP  . indicator
  Blinks red when the internal temperature of the 
projector exceeds the operating range (pp.61, 68).
e	ON/STAND-B y button
  Turn the projector on or off (pp.24–25).
r	INPUT button
  Select an input source (pp.34–35).
!1	INFO  . button
  Display the input source information (p.28).
y	POINT ed7 8 (VOLUME +/–) buttons
  – Select an item or adjust the value in...

14
q STAND-B y button
  Turn the projector off (p.25).
t ON button
  Turn the projector on (p.24).
y INPUT 1 – 3 buttons
  Select an input source (INPUT 1 – INPUT 3) (pp.34–
35).
u	AUTO PC button
  Automatically adjusts the computer image to its 
optimum setting (pp.30, 38).
i FREEZE button
  Freeze the picture on the screen (p.30).
o	POINT ed 7 8 ( VOLUME + / – ) buttons
  – Select an item or adjust the value in the On-
Screen Menu (p.26).
  – Pan the image in Digital zoom + mode (p.47).
  – Adjust the...

15
Remote Control
!3 MENU button
  Open or close the On-Screen Menu (p.26).
!6	ZOOM ed buttons
  Zoom in and out the images (p.30).
!5	D .ZOOM button
  Select the Digital zoom +/- mode and resize the 
image (p.47).
@0	FOCUS button
  Adjust the focus (p.30).
!8	MUTE button
  Mute the sound (p.29).
!4	P-TIMER button
  Operate the P-timer function (p.31).@1	NO SHOW button
  Temporarily turn off the image on the screen (p.31).
@2	KEy STONE button
  Correct keystone distortion (p.31).
@6	SELECT button
  –...

16
Projection angle can be adjusted up to 5.0 degrees with the 
adjustable feet. 
Rotate the adjustable feet and tilt the projector to the proper 
height; to raise the projector, rotate the both feet clockwise.
To lower the projector or to retract the adjustable feet, rotate 
the both feet counterclockwise.
To correct keystone distortion, press the KEYSTONE button 
on the remote control or select Keystone from the menu 
(see pages 15, 31, 45).
Adjustable Feet
Adjustable Feet
To ensure safe operation,...

17
The eight different remote control codes (Code 1–Code 8) are assigned to this pro\
jector. Switching the remote 
control codes prevents interference from other remote controls when several projectors or video equipment 
next to each other are operated at the same time. Change the remote control code for the projector first before 
changing that for the remote control. See “Remote control” in the Setting Menu on page 52.
Press and hold the MENU and a number button (1–8) 
for more than five seconds to...

18
✔Note:
	 •	The	brightness	in	the	room	has	a	great	influence	on	picture	quality.	It	is	recommended	to	limit	 ambient	lighting	in	order	to	obtain	the	best	image.
	 •	All	measurements	are	approximate	and	may	vary	from	the	actual	sizes.
For projector positioning, see the figures below. The projector should be set perpendicularly to the plane of the 
screen. 
1 0.30m
6.84m
5.1 1m
3.38m
1 .26m
10 0” 32.8 (1
0.0m)
22.4 (6.84m)
16 .8 (5.1 1m)
1 4.4 (4.39m)
3.9 (1 .2m)
150” 20
0” 30
0”
230”
1 55”
1 1 6”
78”...

When replacing the lens or using an optional lens, install the lens by following the instructions below. Ask the 
sales dealer for detailed information of the optional lens specifications. 
19
When replacing the lens or using an optional lens, install the lens by following the instructions below. Ask the 
sales dealer for detailed information of the optional lens specifications. Fit the lens to the projector by aligning the red dot 
on the lens with the red dot of the projector. Remove the lens mount...

20
Connecting to a Computer (Digital and Analog RGB)
Cables used for connection 
• VGA Cable (HDB 15 pin)* • USB Cable
• DVI-Digital Cable  • Audio Cables (Mini Plug [stereo] x 2)
• BNC Cable 
(*One cable is supplied; other cables are not supplied with the project\
or.)
External Audio Equipment
DVI-Digital 
cable USB 
cable
Audio 
cable 
(stereo)
Audio cable 
(stereo)
USB port
Audio 
Output
USB
AUDIO OUT 
(stereo)Audio Input
Unplug the power cords of both the projector and external 
equipment from the AC...