Eiki Projector Lc Sxg400 User Manual

							61
The WARNING indicators show the state of the function which protects the projector. Check the state of the 
WARNING indicators and the POWER indicator to take proper maintenance. 
Warning Indicators
The projector is shut down and the WARNING TEMP. 
indicator is blinking red.
When the temperature inside the projector reaches a 
certain level, the projector will be automatically shut 
down to protect the inside of the projector. The POWER 
indicator is blinking while the projector is being cooled 
down. When the projector has cooled down enough (to its 
normal operating temperature), it can be turned on again by 
pressing the ON/STAND-BY button.
✔Note:
	 •	The	 WARNING	 TEMP.	indicator	continues	to	blink	
even	after	the	temperature	inside	the	projector	
returns	to	normal.	 When	the	projector	is	turned	on	
again,	the	 WARNING	 TEMP.	indicator	stops	blinking.	
Then check the matters below:
–  Did you provide appropriate space for the projector to be 
ventilated? Check the installing condition to see if the air 
vents of the projector are not blocked.
–   Has the projector been installed near an Air-Conditioning/ 
Heating Duct or Vent? Move the installation of the 
projector away from the duct or vent.
–   Is the filter clean? Clean the filter periodically or replace it 
with a new one.
The projector is shut down and all five indicators are 
blinking.
When the projector detects an abnormal condition, it will 
be automatically shut down to protect the inside of the 
projector and all five indicators on the top panel blink. In 
this case, unplug the AC power cord and plug it, and then 
turn on the projector once again to verify operation. If the 
projector cannot be turned on and these indicators are still 
blinking, unplug the AC power cord and contact the service 
station.
CAUTION
DO NOT LEAVE THE PROJECTOR WITH THE 
AC POWER CORD CONNECTED UNDER AN 
ABNORMAL CONDITION. IT MAY RESULT IN FIRE 
OR ELECTRIC SHOCK.
WARNING TEMP  .
blinking red
Top Control
All five indicators 
are blinking
Top Control
Maintenance and Filter Cleaning 
						

							62
Unplug the AC power cord before cleaning.
Gently wipe the projection lens with a cleaning cloth that 
contains a small amount of non-abrasive camera lens cleaner, 
or use a lens cleaning paper or commercially available air 
blower to clean the lens. 
Avoid using an excessive amount of cleaner. Abrasive 
cleaners, solvents, or other harsh chemicals might scratch 
the surface of the lens.
When the projector is not in use, replace the lens cap.
Cleaning the Projector Cabinet
Unplug the AC power cord before cleaning.
Gently wipe the projector body with a soft dry cleaning 
cloth. When the cabinet is heavily soiled, use a small 
amount of mild detergent and finish with a soft dry cleaning 
cloth. Avoid using an excessive amount of cleaner. Abrasive 
cleaners, solvents, or other harsh chemicals might scratch 
the surface of the cabinet.
When the projector is not in use, put the projector in 
an appropriate carrying case to protect it from dust and 
scratches.
Cleaning the Projection Lens
Maintenance and Filter Cleaning 
						

							63
Troubleshooting
Before calling your dealer or service center for assistance, check the items below once again.
– Make sure you have properly connected the projector to peripheral equipment as described \
on pages 20–22. 
–  Make sure all equipment is connected to AC outlet and the power is turned on.
–  When the projector does not project an image from the connected computer\
, restart the computer.  
 Problem:  – Solutions
  No power  – Plug the power cord of the projector into the AC outlet. 
    – See if the POWER indicator is lit. 
    – Wait 90   seconds after the projector is turned off when turning the    
     projector back on. The projector can be turned on after the POWER    
     indicator stops blinking. See on page 25. 
    – Check the WARNING TEMP. indicator. If the WARNING TEMP.      
     indicator is blinking, the projector cannot be turned on. See page 61.   
    – Check the projection lamp. See page 59. 
    – Unlock the Key lock function for the projector. See page 54.
  PIN code dialog box appears   – PIN code lock is being set. Enter a PIN code; the "1234" or numbers    
  at start-up .   you have set. See pages 24, 55–56.
  The initial display is not shown .  – Make sure "Off" or "Countdown Off" are not chosen at Display function.  
     See page 52.
  The initial display is not same with  – Make sure "User" or "Off" are not chosen at Logo function. See page 50. 
  the default one .
  An icon other than Input mode or  – That is the Lamp replacement icon or the Filter warning icon.      
  Lamp mode icon appears .   See pages 57, 59.
  No image  – Check the connection between your computer or video equipment and  
     the projector. See pages 20–22. 
    – See if the input signal is correctly output from your computer. Some    
     laptop computers may need to change the setting for monitor output    
     when connecting to the projector See your computer’s instruction    
     manual for the setting.  
    – It takes about 30 seconds to display an image after turning on the    
     projector. 
    – See if the selected system is corresponding with your computer or    
     video equipment. See pages 36, 37. 
    – Select correct input source once again through menu operation. See    
     page 35. 
    – Make sure the temperature is not out of the specified Operating    
     Temperature (
41 ˚F–95 ˚F [5 ˚C–35 ˚C]). 
    – When "No Show" is operating, the image can not be displayed. Press    
     the NO SHOW button or any other button on the remote control.
  Image is out of focus .  – Adjust focus of the projector. See pages 28, 30. 
    – Provide proper distance between the projector and projection screen   
     See page 18. 
    – Check the projection lens to see if it needs cleaning. See page 62. 
    – Moving the projector from a cool to warm place may result in moisture  
     condensation on the projection lens. In such cases, leave the projector  
     off and wait until condensation evaporates. 
Appendix 
						

							64
   – Projecting from the excessive slant angle to the screen may cause    
     keystone distortion and partial imperfect focus. See page 18.
  Picture is not bright enough .  – Check if "Contrast" or "Brightness" are adjusted properly See page 42. 
    – Check if "Image level" is selected properly See page 41. 
    – Check the LAMP REPLACE indicator. If it lights, the end of lamp life is 
     approaching. Replace the lamp with a new one promptly. See pages 
     59-60, 69. 
    – Check the Lamp control function See page 49.
  The color is strange .  – Check the Input signal, color system, video system, or computer    
     system mode. 
    – Adjust the Image level properly. See page 41.
  Image is Left/Right reversed .  – Check the Ceiling/Rear function. See page 45. 
  Image is Top/Bottom reversed .  – Check the Ceiling function. See page 45.
  The image is distorted or runs off  . – Check the "PC Adjustment" menu or "Screen" menu and adjust them.   
     See page 37-40, 45-47.
  The edge of image is distorted .  – With maximum lens shift, image distortion may be observed.
  No sound  – Check the audio cable connection from audio input source. 
    – Adjust the audio source. 
    – Press the Volume + button. See page 29. 
    – Press the Mute button. See page 29. 
    – When the AUDIO OUT is plugged in, the projector's built-in speaker is   
     not available. 
    – Is the image projected? You will hear the sound only when the image is  
     projected.
  Auto PC adjustment function    – Check the Input signal. Auto PC Adjustment function can not work.    
  does not work .   when 480p, 575p, 720p, 480i, 575i, 1035i, or 1080i is selected.  
     See page 38. 
    – The Auto adj. icon turns gray and cannot be operated with the digital    
     signals. See page 38.
  Some displays are not seen   – Check the Display function. See page 52.         
  during the operation .
  The setting does not remain after    – Make sure you selected "Store" after adjusting settings. Some settings  
  turning off power  .   cannot be stored if not registered with "Store."
  Power management function does   – Power management function cannot work while "Freeze" or "No Show"  
  not work .   function is running.
  Image disappears automatically   – Check the power management function in the Setting. The power    
     management is set to “On” at the factory.
Appendix 
						

							65
Appendix
This symbol on the nameplate means the product 
is Listed by Under writers Laboratories Inc. It is 
designed and manufactured to meet rigid U.L. 
safety standards against risk of fire, casualty and 
electrical hazards.The CE Mark is a Directive 
conformity mark of the European 
Community (EC).
WARNING :
High voltages are used to operate this projector . Do not attempt to open the cabinet .
If problems still persist after following all operating instructions, contact the dealer where you purchased the 
projector or the service center. Specify the model number and explain about the problem. We will advise you 
how to obtain service.
 
Capture function does not work .  – Check the connection and the Input signal to see if there is signal.
  The Remote Control does  – Check the batteries. 
  not work .  – Make sure no obstruction is between the projector and remote control. 
    – Make sure you are not too far from the projector when using the    
     remote control. Maximum operating range is 16.4’ (5 m). 
    – Make sure that the remote control code conforms to the projector’s    
     code. See page 52. 
    – Unlock the Key lock function for the remote control. See page 54. 
    – Wireless remote control does not work when the remote control cable  
     is connected to the projector.
  Wireless Mouse function does  – Check the connection between the projector and your computer. 
  not work .    – Check the mouse setting on your computer. 
    – Turn on the projector before you turn on the computer. 
    – Make sure the computer input is selected. 
    – Make sure that the mouse driver is installed in your computer. To use the   
     moue as a wireless mouse, the mouse driver needs to be installed in    
     the computer.
  Indicator blinks or lights .  – Check the status of the projector with referring to "indicators and    
     Projector Condition." See pages 68-69.
  The exclamation mark appears   – Your operation is invalid. Operate correctly. 
  on the screen .
  The top control does not work .  – Unlock Key lock for the projector in the Key lock function.
  Unable to unlock the Logo PIN   – Contact the dealer where you purchased the projector or the service    
  code lock, Security key lock    center. 
  or Security PIN code lock . 
						

							66
Menu Tree
Dynamic
RealCinemaImage 1Image 2Image 3
Image
VolumeMuteQuitOn/OffSound0–63
Input
Input 3Auto
Go to System (3)
Go to System (3)
Video 
Go to System (1)
S-video
Standard
Quit
Input 1
Go to System (3)Video
Go to System (1)Input 2 RGB
Go to System (2)Component
Image 4
RGB (PC Analog)
RGB (Scart)
RGB (PC Digital)
RGB (AV HDCP)
Quit
Quit
SySTEM (3)SySTEM (1)
- - - -
Mode 1
Mode 2
XGA 1SECAM
NTSC
Auto
PAL
PAL-M
PAL-N
NTSC4.43
SySTEM (2)
1035i
720p
Auto
1080i
480p
575i
575p
480i
InputH-sync freq.V-sync freq.
PIN code lock
Information
Key lock
ScreenLanguageLamp statusPower managementSecurity
Remote control code
Quit
0–630–63
Off/L1/L2/Film
Image AdjustContrastBrightnessColorTint
RedGreenBlueSharpness
ResetStore
Gamma
Progressive
0–630–630–630–15 0–15
Image 1Yes / No
Quit
Off/L1/L2Noise reduction
0–630–63
Image 2Image 3Image 4
Color temp.High/Mid/Low/XLow
✔Note:
	 •	The	Menu	display	varies	depending	on	the	input	 signal.
Appendix
✽vFor Computer input only.
For Video input only.
✽v
vv
vv 
						

							67
LanguageSetting12 languages provided
Blue/User/BlackAuto 1
Normal
BackgroundLamp control
Quit
Capture
Logo PIN code change
Logo PIN code lock
Quit
Auto 2High
QuitAuto PC adj.
Total dotsHorizontalVertical
Display area HDisplay area VReset
PC Adjust
Yes/No
Clamp
Current mode
Mode free/Store
Quit
Fine sync0–31
Mode 1
H-sync freq.V-sync freq.Quit
NormalTrueWideFull screen
Screen
Logo selectLogoOff/Default/User
Yes/No
On/Off
Eco 1Eco 2
✔Note:
	 •	The	Menu	display	varies	depending	on	the	input	 signal.
Mode 3Mode 4Mode 5
Quit
Mode 2
Mode 8Mode 9Mode 10
Mode 6Mode 7
Digital zoom –
CustomDigital zoom +
Rear
Keystone
CeilingResetStore
On/OffOn/Off
Off/Ready/Shutdown
Code 1–Code 8
Power management
Remote control
Timer (1–30 Min)Quit
Spotlight/PointerPointerQuit
Both/Front/BackRC sensorOn/Countdown off/Off Display
On/OffOn start
Highland
SlantFan controlOff/L1/L2
On/Off
Projector (all)
PIN code change
PIN code lock
Quit
Key lockSecurityOff
Projector (part)
Off/On 1/On 2
Remote control (all)Remote control (part)
8 test patterns providedTest patternQuitWarning logHour(s)Lamp counter
QuitYes/No
Hour(s)Filter counter
QuitYes/NoOff/100H/200H/300H
Reset
Reset
Yes/NoFactory defaultQuit
Appendix
✽vFor Computer input only.
For Video input only.
✽
✽
✽✽ 
						

							68
Check the indicators for the projector condition.  
• • • lighting• • • off• • • blinking
Indicators and Projector Condition
WARNING TEMP . indicator
Appendix
Indicators
Projector ConditionPOWER
green LAMP
red WARNING
TEMP.red
The projector is off. (The AC power cord is unplugged.)
The projector is in stand-by mode. Press the ON/STAND-BY button to 
turn on the projector.
The projector is operating normally.
The projector is in the Power management mode.
The projector is preparing for stand-by or the projection lamp is 
being cooled down. The projector cannot be turned on until cooling is 
completed and the POWER indicator stops blinking.
The WARNING TEMP. indicator blinks slow when the temperature 
inside the projector is elevated close to the abnormally high level.
The temperature inside the projector is abnormally high. The 
projector cannot be turned on. When the projector is cooled down 
enough and the temperature returns to normal, the POWER indicator 
stops blinking and the projector can be turned on. (The WARNING 
TEMP. indicator keeps blinking.) Check and clean the filter.
The projector has been cooled down enough and the temperature 
returns to normal. When turning on the projector, the WARNING 
TEMP. indicator stops blinking. Check and clean the filter.
POWER, LAMP, WARNING 
TEMP., WARNING FILTER, 
and LAMP REPLACE 
indicators are blinking all 
together.The projector detects an abnormal condition and cannot be turned 
on. Unplug the AC power cord and plug it again to turn on the 
projector. If the projector is turned off again, unplug the AC power 
cord and contact the dealer or the service center. Do not leave the 
projector on. It may cause an electric shock or a fire hazard. 
						

							69
* When the projection lamp reaches its end of life, the LAMP REPLACE indicator lights yellow. When this indicator lights 
yellow, replace the projection lamp with a new one promptly. Reset the lamp counter after replacing the lamp. See pages 
59–60.
––
––
WARNING
FILTER
orange
The filter is clogged. Stop using the projector immediately and clean 
or replace the filter (see below).
Projector ConditionPOWERgreen
Indicators
WARNING FILTER indicator
The Filter counter reached a set time. Clean or replace the filter as 
soon as possible.
The lamp cannot light up. (The projector is preparing for stand-by or 
the projection lamp is being cooled down. The projector cannot be 
turned on until cooling is completed.)
The lamp cannot light up. (The lamp has been cooled down enough 
and the projector is in stand-by mode and ready to be turned on with 
the ON/STAND-BY button.)
Projector ConditionPOWERgreen
Indicators
LAMP 
REPLACE
yellow
LAMPred
LAMP REPLACE indicator
The lamp has been used overtime. Replace the lamp immediately 
and then reset the lamp counter. The indicator will be turned off after 
resetting the counter.
If filter clogging is detected during operations, the 
Filter warning icon (red) appears on the screen and the 
WARNING FILTER indicator blinks orange, urging you 
to clean or replace the filter. Stop using the projector 
immediately and clean or replace the filter. The 
WARNING FILTER indicator and Filter warning icon will 
not be turned off until the filter is cleaned or replaced by 
a new one. 
Filter warning icon (red) appears on the screen 
when the projector detects filter clogging.
✔Note:
	 •	The	Filter	warning	icon	(red)	will	not	 appear	during	 “Freeze”	(p.30),	or	 “No	
show”	(p.31).
Filter warning red icon
Filter warning yellow icon
LAMPred
Appendix 
						

							70
Compatible Computer Specifications
Basically this projector can accept the signal from all computers with th\
e V- and H-Frequency mentioned 
below and less than 165 MHz of Dot Clock. PC Adjustment is limited when selecting these modes.
Appendix
ON-SCREEN 
DISPLA yRESOLUTION H-Freq .
(kHz) V-Freq .
(Hz)
VGA 1 640x480 31.470 59.880 
VGA 2 720x400 31.470 70.090 
VGA 3 640x400 31.470 70.090 
VGA 4 640x480 37.860 74.380 
VGA 5 640x480 37.860 72.810 
VGA 6 640x480 37.500 75.000 
VGA 7 640x480 43.269 85.000 
MAC LC13 640x48034.970 66.600 
MAC 13 640x480 35.000 66.670 
480p 640x480 31.470 59.880 
575p 768x575 31.250 50.000 
575i 768x576 15.625
50.000
(Interlace)
480i 640x480 15.734 60.000
(Interlace)
SVGA 1 800x600 35.156 56.250 
SVGA 2 800x600 37.880 60.320 
SVGA 3 800x600 46.875 75.000 
SVGA 4 800x600 53.674 85.060 
SVGA 5 800x600 48.080 72.190 
SVGA 6 800x600 37.900 61.030 
SVGA 7 800x600 34.500 55.380 
SVGA 8 800x600 38.000 60.510 
SVGA 9 800x600 38.600 60.310 
SVGA 10 800x600 32.700 51.090 
SVGA 11 800x600 38.000 60.510 
MAC 16 832x624 49.720 74.550 
XGA 1 1024x768 48.360 60.000 
XGA 2 1024x768 68.677 84.997 
XGA 3 1024x768 60.023 75.030 
XGA 4 1024x768 56.476 70.070 
XGA 5 1024x768 60.310 74.920 
XGA 6 1024x768 48.500 60.020 
XGA 7 1024x768 44.000 54.580 
XGA 8 1024x768 63.480 79.350 
XGA 9 1024x768 36.000
870170
(Interlace)
XGA 10 1024x768 62.040 77.070 
XGA 11 1024x768 61.000 75.700 
XGA 12 1024x768 35.522
86.96
(Interlace)
XGA 13 1024x768 46.900 58.200 
XGA 14 1024x768 47.000 58.300 
XGA 15 1024x768 58.030 72.000 
MAC 19 1024x768 60.240 75.080 
SXGA 1 1152x864 64.200 70.400 
SXGA 2 1280x1024 62.500 58.600 
ON-SCREEN 
DISPLA yRESOLUTION H-Freq .
(kHz) V-Freq .
(Hz)
SXGA 3 1280x1024 63.900 60.000 
SXGA 4 1280x1024 63.340 59.980 
SXGA 5 1280x1024 63.740 60.010 
SXGA 6 1280x1024 71.690 67.190 
SXGA 7 1280x1024 81.130 76.107 
SXGA 8 1280x1024 63.980 60.020 
SXGA 9 1280x1024 79.976 75.025 
SXGA 10 1280x960 60.000 60.000 
SXGA 11 1152x900 61.200 65.200 
SXGA 12 1152x900 71.400 75.600 
SXGA 13 1280x1024 50.000
86.000
(Interlace)
SXGA 14 1280x1024 50.00094.00
(Interlace)
SXGA 15 1280x1024 63.370 60.010 
SXGA 16 1280x1024 76.970 72.000 
SXGA 17 1152x900 61.850 66.000 
SXGA 18 1280x1024 46.43
86.70
(Interlace)
SXGA 19 1280x1024 63.790 60.180 
SXGA 20 1280x1024 91.146 85.024 
SXGA+ 1 1400x1050 63.970 60.190 
SXGA+ 2 1400x1050 65.350 60.120 
SXGA+ 3 1400x1050 65.120 59.900 
SXGA+ 4 1400x1050 64.03060.010
SXGA+ 5 1400x1050 62.50058.600
MAC 21 1152x870 68.680 75.060 
MAC 1280x960 75.000 75.080 
MAC 1280x1024 80.000 75.080 
WXGA 1 1366x768 48.360 60.000 
WXGA 2 1360x768 47.700 60.000 
WXGA 3 1376x768 48.360 60.000 
WXGA 4 1360x768 56.160 72.000 
WXGA 6 1280x768 47.776 59.870 
WXGA 7 1280x768 60.289 74.893 
WXGA 8 1280x768 68.633 84.837 
UXGA 1 1600x1200 75.000 60.000 
UXGA 2 1600x1200 81.250 65.000 
UXGA 3 1600x1200 87.500 70.000 
UXGA 4 1600x1200 93.750 75.000 
UXGA 5 1600x1200 106.250 85.000 
720p 1280x720 45.000 60.000 
720p 1280x720 37.50050.000 
1035i 1920x1035 33.750
60.000
(Interlace)
1080i 1920x1080 33.75060.000
(Interlace)
1080i 1920x1080 28.12550.000
(Interlace)